煤粉炉掺烧干化污泥的污染物排放研究

结合某电厂420 t/h四角煤粉炉掺烧污泥项目的实验室分析测试,了解煤粉掺烧不同含水率不同比例的干化污泥条件下烟气中污染物和灰渣中重金属的排放特性.结果表明,在实验研究配比和燃烧的条件下,大部分重金属元素Pb、Cu、Cr和Ni残留在灰渣中,Zn、Cd部分残留在灰渣中, As、Hg和Se等易挥发元素释放到烟气中,在灰渣中的含量很小.掺烧污泥后,灰渣中的重金属含量较单烧单煤都有了一定幅度的升高,Zn的含量是单煤的2倍,其余重金属是单煤的1.1~1.2倍.3种不同的掺混比例之间的污染气体排放浓度基本相似.烟气中主要污染物及重金属浓度可以满足现行国家标准.与单烧单煤相比,CO、HCl以及其他有机气体排放浓度基本相同;NH3的排放浓度较单煤有所升高;SO2、NOx和CO2排放浓度略有降低;飞灰浓度有所升高.烟气中的重金属,Hg含量升高了30%,Pb含量约为单煤的4.3~4.8倍.以上研究结果可为环保达标和飞灰利用提供基础数据.     

锰污染土壤根际微生物分离及耐Mn2+特性

为了研究锰污染土壤的生物修复,在湘潭锰矿不同植物根际土壤中分离得到7株真菌和8株细菌,依次命名为F1-7和B1-8。经耐锰性能测定,获得高耐锰性真菌3株,F3-5、细菌3株,B1、B2和B7。其中,F3耐锰浓度最高可达600mmol/L,细菌B7最高耐锰浓度为80 mmol/L。当Mn2+浓度小于300 mmol/L时,对3种真菌的生长均具有一定的促进作用,高于此浓度时,产生较大程度的抑制作用。在低Mn2+浓度(20~40 mmol/L)条件下,Mn2+对3种细菌的生长均表现出一定的促进作用,尤其是对B2作用明显。当Mn2+浓度逐渐增加到80 mmol/L时,抑制作用明显。在Mn2+浓度为300mmol/L时,F3对锰的吸附率约为60%,达到峰值。而在Mn2+浓度为60 mmol/L时,细菌B2对锰的吸附率约为70%,达最大值。     

气浮技术在膜生物反应器剩余污泥浓缩过程中的应用

污泥浓缩作为污泥处理的关键环节之一,开发高效的污泥浓缩工艺对于降低污泥含水率、提高脱水设备的运行效率、降低脱水能耗具有十分重要的意义。针对MBR污泥浓度高、污泥粒径小、污泥沉降性能较差等特点,故采用传统的重力浓缩和机械浓缩技术很难有效实现污泥浓缩。因此,尝试采用气浮浓缩技术降低污泥含水率的可行性。从气浮浓缩的中试结果来看,较适宜运行参数为:固体负荷为15 kg/(m2·h),水力负荷为1.5 m3/(m2·h),回流比为1,PAM投配率2‰(w/w干固体),溶气压力为0.4 MPa,气固比为0.03。经过中试设备进行气浮浓缩后,污泥含水率降低至96%左右。此外,还研究了采用气液多相泵系统对剩余污泥的浓缩效率,结果显示,该设备的使用相对于传统溶气气浮工艺,其优点表现在占地小、工程造价低以及运行成本低等方面。     

改性丝瓜络纤维对水体日落黄的吸附特性

采用化学改性的方法将丝瓜络制备为阴离子吸附剂,并将其用于水体日落黄(SY)染料的吸附,分别考察了吸附剂的用量、日落黄染料的初始浓度(C0)、pH值、温度(K)、时间(T)5个因素对吸附效果的影响。通过模拟吸附等温曲线、吸附动力学以及热力学方程并通过比表面积(BET)和红外光谱(FTIR)分析改性丝瓜络吸附染料前后和丝瓜络改性前后的变化情况以此探究其吸附机理。结果表明,pH对吸附效果影响不明显;最大吸附量随温度升高而增大,在298 K温度时最大吸附量达到137 mg/g,是未改性丝瓜络的9.78倍。Langmuir方程拟合吸附过程描述最好,吸附类别为化学吸附。吸附过程符合伪二级动力学,是一个自发和吸热的过程。改性丝瓜络可以有效去除水体中的日落黄染料。     

3种组合工艺处理农村生活污水

进行了厌氧折流板反应器-垂直潜流人工湿地(ABR-VSFCW)、复合厌氧反应器-水平潜流人工湿地(HAR-HSFCW)、膨胀颗粒污泥床-人工快速渗滤系统(EGSB-CRI)3种组合工艺处理农村生活污水的研究。结果表明,在温度为10~29℃,进水COD为325.3~386.5 mg/L的条件下,3种组合工艺对COD均有较高的处理效果,当厌氧段HRT大于16 h时,3种组合工艺出水COD浓度均达到了我国《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级B标准;EGSB-CRI、HAR-HSFCW对TP的去除效果较好,出水TP浓度均达到了我国《城镇污水处理厂污染物排放标准》(GB 18918-2002) 一级B标准, 且显著优于ABR-VSFCW,ABR-VSFCW出水TP浓度达到了二级标准; ABR-VSFCW、HAR-HSFCW、EGSB-CRI出水NH4+-N浓度分别为25.24~42.20、29.59~41.60和9.80~15.35 mg/L,其出水NH4+-N浓度达到了我国《城镇污水处理厂污染物排放标准》(GB 18918-2002)二级标准;3种组合工艺对TN的去除效果无明显差异,去除率仅为23.9%~46.4%。因此,EGSB-CRI对农村生活污水的处理效果最好,HAR-HSFCW次之,ABR-VSFCW较差。     

Fe(Ⅱ)EDTA络合吸收-铁粉还原再生脱除NO性能

利用Fe(Ⅱ)EDTA络合吸收-铁粉间歇还原再生脱除NO并回收氨资源的方法,实验研究了铁粉还原再生Fe(Ⅱ)(NO)EDTA的过程及其影响因素。结果表明,以0.015 mol/L的Fe(Ⅱ)EDTA做吸收剂,在起始pH 5.5、温度323K条件下吸收400×10-6~500×10-6的NO,脱除率95%以上;铁粉还原再生Fe(Ⅱ)(NO)EDTA过程可用缩芯模型阐释;铁粉添加量与搅拌强度直接决定了铁粉质点数量,是影响反应的重要因素;实验中Fe(Ⅱ)(NO)EDTA络合液150 mL,氧气含量为5%时,搅拌速度900 r/min、粒径为0.12 mm的铁粉浓度5.3 g/L、温度353 K、pH=6为最适宜再生条件。     

厦门市空气污染的空间分布及其与影响因素空间相关性分析

基于空间信息技术、克里格插值与空间相关矩阵,研究厦门市SO2、NO2、PM10和PM2.5污染浓度空间分布特征。通过提取人口密度、道路面积比重、建设用地比重、地表温度及植被指数等空气污染影响因素的空间分布数据,划分研究区为生态区、居住区与工业区,定量评价了污染物浓度与影响因素的空间相关性,并识别出各污染物的主要影响因素。结果表明:污染浓度分布总体上呈现出工业区-居住区-生态区递减的空间特征,其主要受工业排放和机动车排放的影响;SO2与除地表温度外的其他影响因数均有较强空间相关性,PM10和PM2.主要与道路面积比重、建设用地比重具有较强相关性,NO2则与道路面积比重的相关性最强,污染浓度与影响因数空间相关性呈现出工业区-居住区-生态区递增趋势;与按照行政区的划分相比,工业区、居住区、生态区的划分显得更为合理。     

表面印迹聚合物吸附复杂基质中的土霉素

为了研究表面分子印迹聚合物对基质复杂的环境样品中的土霉素的吸附分离效果,以应用最为广泛的土霉素(OTC)为研究对象,利用甲基丙烯酸和甲基丙烯酸甲酯为双功能单体、在二氧化硅基质上制备了表面分子印迹聚合物,并对其吸附鸡粪中的四环素类抗生素进行了研究。以聚合物的吸附容量和印迹因子为考核指标,对两种单体的投加比例和二氧化硅的用量进行了优化,确定其合成最佳条件:二氧化硅用量为15 mmol、单体总量一定时各物质的摩尔比为OTC:MAA:MMA:EGDMA=0.08:2.0:2.0:8.0。在此条件下合成的表面印迹聚合物对鸡粪基质中的OTC的最大吸附量可达到9.67 mg/g,印迹因子4.69,可见该表面印迹聚合物对复杂环境样品中的OTC也有良好的吸附性能和识别性能。     

A comparison of statistical methods for deriving freshwater quality criteria for the protection of aquatic organisms

Species sensitivity distributions (SSDs) are increasingly used in both ecological risk assessment and derivation of water quality criteria. However, there has been debate about the choice of an appropriate approach for derivation of water quality criteria based on SSDs because the various methods can generate different values. The objective of this study was to compare the differences among various methods. Data sets of acute toxicities of 12 substances to aquatic organisms, representing a range of classes with different modes of action, were studied. Nine typical statistical approaches, including parametric and nonparametric methods, were used to construct SSDs for 12 chemicals. Water quality criteria, expressed as hazardous concentration for 5 % of species (HC₅), were derived by use of several approaches. All approaches produced comparable results, and the data generated by the different approaches were significantly correlated. Variability among estimates of HC₅ of all inclusive species decreased with increasing sample size, and variability was similar among the statistical methods applied. Of the statistical methods selected, the bootstrap method represented the best-fitting model for all chemicals, while log-triangle and Weibull were the best models among the parametric methods evaluated. The bootstrap method was the primary choice to derive water quality criteria when data points are sufficient (more than 20). If the available data are few, all other methods should be constructed, and that which best describes the distribution of the data was selected.     

Adsorption of multi-heavy metals Zn and Cu onto surficial sediments: modeling and adsorption capacity analysis

Improved multiple regression adsorption models (IMRAMs) was developed to estimate the adsorption capacity of the components [Fe oxides (Fe), Mn oxides (Mn), organic materials (OMs), residuals] in surficial sediments for multi-heavy metal Zn and Cu. IMRAM is an improved version over MRAM, which introduces a computer program in the model developing process. As MRAM, Zn(Cu) IMRAM, and Cu(Zn) IMRAM again confirmed that there is significant interaction effects that control the adsorption of compounded Zn and Cu, which was neglected by additional adsorption model. The verification experiment shows that the relative deviation of the IMRAMs is less than 13 %. It is revealed by the IMRAMs that Mn, which has the greatest adsorption capability for compounded Zn and Cu (54.889 and 161.180 mg/l, respectively), follows by interference adsorption capacity of Fe/Mn (?1.072 and ?24.591 mg/l respectively). Zn and Cu influence each other through different mechanisms. When Zn is the adsorbate, compounded Cu mainly affects the adsorption capacities of Fe/Mn and Fe/Mn/OMs; while when Cu is the adsorbate, compounded Zn mainly exerts its effect on Mn, Fe/Mn, and Mn/OMs. It also shows that the compounded Zn or Cu weakened the interference adsorption of Fe/Mn, and meanwhile, strengthened the interference adsorption of Mn/OMs.