金属加工过程中应力状态的分析方法

分析简单地拉伸、压缩和扭转的情况时,应力状态能容易地被确定.但是,实际上在金属加工过程中材料是承受复杂的应力状态,在模具——工件接触面上增加有摩擦力.而且,这些应力和摩擦力一般地沿着接触面变化.准确的计算或预测载荷、力、应力和温度,不但对设计适宜的设备是重要的,而且对研究工艺期间材料的变化过程也是重要的.本文将讨论材料变形过程中所运用的主要分析方法及其优缺点.     

好氧颗粒污泥对有机物吸附类型的研究

为探索好氧颗粒污泥对有机物的去除机制,进行好氧颗粒污泥对有机物的吸附性能及吸附类型研究,在实验室条件下,采用动态吸附方式,利用SBAR反应器分析好氧颗粒污泥对有机物的去除情况。结果表明,好氧颗粒污泥存在初期吸附作用,最佳吸附时间为30~45 min,COD去处率60%;通过对失活前后好氧颗粒污泥对有机物吸附性能测定以及红外光谱分析,探究好氧颗粒污泥对有机物的吸附类型,表明好氧颗粒污泥对有机物的吸附是一个包含生物吸附和化学吸附的复杂过程。     

A study on the interactions among several plant secondary compounds and aphids

The research, focused on the specific interactions among seven plant secondary compounds and aphids, was carried out and the preliminary results showed: (1) "T-typed tube method" was regarded as the best method compared with others designed to observe the interactions. (2) Cabbage aphid was able to be attracted by laurolene while it was not susceptible to α-pinene, β-pinene and diamylene. (3) Gossypol, a major secondary substance in cotton, was able to be implicated as feeding attractant to cotton aphid. (4) Rutin might be implicated repellent to cotton aphid.     

土壤全氮的快速测定

本方法是过硫酸盐氧化消化样品的基础上测定土壤中全氮的光度法.采用碱性过硫酸钾溶液(0.37mol/L K_2S_2O_3,0.375N NaOH)消化土壤样品,然后用百里酚光度法进行测定,具有准确、灵敏、快速、简便等优点,适用于常规和大量样品的分析.     

Occurrence and congeners specific of poiychlorinated biphenyls in agricultural soils from Southern Jiangsu, China

A total of 198 agricultural soil samples were collected from Zhangjiagang and Changshu in Southern Jiangsu for analysis of 13 polychlorinated biphenyls (PCBs) in order to assess the levels of pollution, sources, area distribution, and potential risk for the environment. All methods were rigorously tested and an adequate quality control was ensured. Only one site had no PCBs residues, and the highest total PCBs concentration in the surface soils was 32.83 ng/g. The average concentration in all the soil samples was 4.13 ng/g, signaling low-level pollution. Tetra-, penta-, and hexa-chlorinated biphenyls were dominant species in soil samples, accounting for more than 75% ofΣPCBs in the soil samples. PCB118 was the most abundant congener in all the samples. The PCB118 was about 20% ofΣPCBs. The soil organic matter content showed only a weak correlation with the levels of all PCB congeners, in which a better correlation was noted for the more volatile lighter PCB congeners than for the heavier homologues. To a certain extent, the sources and land use seemed to influence the levels of PCBs.     

ASM1中废水和污泥组分浓度的测定方法研究

对呼吸计量法应用于校准ASM1作了简明的阐述。在呼吸速率与模型组分关系的基础上,介绍了ASM1中废水与污泥各组分浓度的测定方法,并指出模型组分细化的意义。     

楔横轧轴肩的成形曲面的设计

此文分析在二辊楔横轧中轧制各类轴肩的过程。在假想工件轴端固定的图上确定楔侧面截面轮廓形状,再通过叠加轴向刚性移动量确定各截面实际位置,比较直观简便地设计出轧制轴肩的辊面上的成形曲面。最后归纳了设计步骤。     

数值模拟的可视化及其实现技术

此文介绍了一个用于数值模拟过程的二维图形界面,它由两大部分组成:“MANU”实现计算结果的手工操作显示及编辑,“AUTO”用于数值计算过程的自动跟踪.文中详细介绍了系统的设计方法、结构、工作原理和主要功能.     

梯齿形桥梁伸缩缝U形弯曲件的成形技术

此文介绍一种新型桥梁伸缩缝关键零件U形弯曲件的成形技术.通过对该零件的变形分析和采用合理的工艺措施,使得这一成形难度较大的弯曲件一次压制获得成功.