A management system for end-of-life tyres: a Portuguese case study

The European Union introduced several policy instruments based in the extended producer responsibility (EPR) in order to improve the environmental performance of products and services through their life cycles. In this context, the Portuguese government decided to apply the EPR concept to tyres, and producers were obliged to constitute an end-of-life management system to promote the collection, recycling and reuse of end-of-life (EOL) tyres. This required producers, distributors, recyclers and retreaders to be identified and characterized, and local processing infrastructures to be analyzed. The information was used to design an economically optimised EOL tyre management system while promoting the activity of all EOL operators in order for the imposed collecting and recovery targets to be fulfilled. This paper discusses the interaction between the different governmental, private and academic institutions for the creation of the integrated management system for EOL tyres, the approach taken, the technical, political and legal aspects underneath them, as well as the environmental consequences induced by the creation of the management system. The results obtained during the first years of operation are reported and show an increase in the collection and recycling of EOL tyres and the consolidation of the collection and processing infrastructures.     

Treatment and use of air pollution control residues from MSW incineration: an overview

This work reviews strategies for the management of municipal solid waste incineration (MSWI) residues, particularly solid particles collected from flue gases. These tiny particles may be retained by different equipment, with or without additives (lime, activated carbon, etc.), and depending on the different possible combinations, their properties may vary. In industrial plants, the most commonly used equipment for heat recovery and the cleaning of gas emissions are: heat recovery devices (boiler, superheater and economiser); dry, semidry or wet scrubbers; electrostatic precipitators; bag filters; fabric filters, and cyclones. In accordance with the stringent regulations in force in developed countries, these residues are considered hazardous, and therefore must be treated before being disposed of in landfills. Nowadays, research is being conducted into specific applications for these residues in order to prevent landfill practices. There are basically two possible ways of handling these residues: landfill after adequate treatment or recycling as a secondary material. The different types of treatment may be grouped into three categories: separation processes, solidification/stabilization, and thermal methods. These residues generally have limited applications, mainly due to the fact that they tend to contain large quantities of soluble salts (NaCl, KCl, calcium compounds), significant amounts of toxic heavy metals (Pb, Zn, Cr, Cu, Ni, Cd) in forms that may easily leach out, and trace quantities of very toxic organic compounds (dioxin, furans). The most promising materials for recycling this residue are ceramics and glass-ceramic materials. The main purpose of the present paper is to review the published literature in this field. A range of studies have been summarized in a series of tables focusing upon management strategies used in various countries, waste composition, treatment processes and possible applications.     

Application of multi-criteria decision-making on strategic municipal solid waste management in Dalmatia, Croatia

The efficiency of providing a waste management system in the coastal part of Croatia consisting of four Dalmatian counties has been modelled. Two multi-criteria decision-making (MCDM) methods, PROMETHEE and GAIA, were applied to assist with the systematic analysis and evaluation of the alternatives. The analysis covered two levels; first, the potential number of waste management centres resulting from possible inter-county cooperation; and second, the relative merits of siting of waste management centres in the coastal or hinterland zone was evaluated. The problem was analysed according to several criteria; and ecological, economic, social and functional criteria sets were identified as relevant to the decision-making process. The PROMETHEE and GAIA methods were shown to be efficient tools for analysing the problem considered. Such an approach provided new insights to waste management planning at the strategic level, and gave a reason for rethinking some of the existing strategic waste management documents in Croatia.     

Degradation of Polylactic Acid (PLA) Plastic in Costa Rican Soil and Iowa State University Compost Rows

In this study the degradation of polylactic acid (PLA) plastic films in Costa Rican soil and in a leaf composting environment was investigated. Three types of PLA films were used: Ch-I, (PLA monolayer plastic films from Chronopol, Golden, CO), GII (PLA trilayer plastic films from Cargill Dow Polymers LLC, Minnetonka, MN), and Ca-I (PLA monolayer plastic films from Cargill Dow Polymers LLC). The average soil temperature and moisture content in Costa Rica were 27°C and 80%, respectively. The average degradation rate of PLA plastic films in the soil of the banana field was 7675 M _w/week. Two compost rows were set up at the Iowa State University (ISU) (Ames) compost site. Temperature and relative humidity of the compost rows were kept at 55 ± 5°C and 50 ± 10% RH, respectively. The degradation rates of GII and Ca-I in the compost rows were 113,290 and 71,283 M _w/week, respectively. Therefore, it was estimated that in Costa Rican soil and in compost rows, PLA would be visibly degraded in 6 months and in 3 weeks, respectively.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Co-combustion of dried sewage sludge and coal in a pulverized coal boiler

More than 1.1 million tons of municipal and industrial sewage sludge is produced annually in Poland. Most of this sewage sludge is landfilled or used for recultivation and fertilization of soil. After accession of Poland to the EU, large investments are planned for wastewater treatment, so it is expected that the amount of sewage sludge produced in Poland will grow in the near future. It is well known that the combustion of sewage sludge is becoming a more and more popular utilization method of such waste. Unfortunately, the current situation in Poland makes it impossible to incinerate the sewage sludge because of a lack of incinerators. One possible solution for Poland is the co-firing of dried sewage sludge in existing coal-fired utility boilers. This article presents results of initial Polish industrial trials of dried municipal sewage sludge and hard coal co-combustion in an OP-230 pulverized coal boiler. Such a solution was shown to be technically viable and not to require changes to the existing technological system. Cocombustion of sewage sludge with coal in power plants seems to be the best solution for sludge utilization in the near future in Poland.     

Study of Pollution of the Plitvice Lakes by Water and Sediment Analyses

The process of eutrophication in form of intense plant growth has been observed in some lakes and water streams at the Plitvice Lakes National Park in central Croatia. Here we investigate whether this phenomenon is a consequence of anthropogenic pollution or due to naturally produced organic matter in the lakes. We applied chemical analysis of water at two springs and four lakes (nutrients, dissolved organic carbon (DOC), trace elements) and measurements of surface lake sediments (mineral and organic fraction analyses, trace elements) in four different lakes/five sites. The chemical composition of water does not indicate recent anthropogenic pollution of water because the concentrations of most trace elements are below detection limits. The concentrations of DOC and nutrients are slightly higher in the area of increased eutrophication-plant growth. Also the content of organic matter in the sediment is at the highest level in areas with highest C/N ratio indicating that the organic fraction of this sediment is mainly of terrestrial origin. There is no significant difference among the trace element concentration in the upper segment of all cores, deposited approximately during last 50 years when higher anthropogenic influence is expected due to development and touristic activity, and the lower part of the cores, corresponding to the period approximately 100–200 years before present. The content of trace elements and organic matter in sediments decreases from the uppermost lake downstream. According to our results there is no indication of recent anthropogenic pollution in water and sediment. Higher concentrations of DOC in water as well as phosphorus and some other elements in the lake sediment can be a consequence of input of natural organic matter to the lake water.     

Sulfur Metabolism in Polluted Sphagnum Peat Bogs: A Combined 34S–35S–210Pb Study

The size and isotopic behavior of sulfur pools in²¹⁰Pb-dated peat cores were investigated to obtain aninsight into retention mechanisms of pollutant S in twomountain-top peatlands of the Northern Czech Republic, CentralEurope. The bogs were situated 40 km apart in an area whichbetween the years 1985 and 1995 received as much as 130 kg Sha^-1 yr^-1 from the atmosphere. Vertical peataccretion was faster at Pod Jelení horou (JH) than atVelký moál (VM). Organic carbon-bonded S was themost abundant sulfur pool, constituting 77 and 65 wt. % at JHand VM, respectively. At JH both the S concentration maximumand the highest annual S deposition rate were displaceddownward by more than 20 years (from 1987 to the 1960s)indicating that the buried S is vertically mobile. At VM the Sconcentration was the highest in the topmost 2-cm section eventhough atmospheric S deposition peaked in 1987. Differentmechanisms of S isotope redistribution prevailed in thetopmost peat layers at JH, where a negative ³⁴Sshift occurred, and at VM, where a positive ³⁴Sshift occurred. Bacterial sulfate reduction was responsiblefor the negative ³⁴S shift at JH. One possibleexplanation of the positive ³⁴S shift at VM isrelease of ³²S-enriched products of mineralization duringpeat diagenesis. There was a strong positive correlationbetween the abundance of total and pyrite S along the profiles.The presence of pyrite S at VM (526 ± 60 ppm) suggestedthat even at VM bacterial sulfate reduction occurred. Ananaerobic incubation of JH peat indicated sulfate reductionrate of 600 nmol g^-1 day^-1. The turnover times forinorganic S pools were shorter than for the organic S pools.Cumulative S contents in the Czech peat bogs were found to besignificantly lower than in similar sites in the NortheasternU.S., even though the atmospheric S inputs were more thanthree times higher at the Czech sites. Possible causes of suchdiscrepancy are discussed.     

Percolation and batch leaching tests to assess release of inorganic pollutants from municipal solid waste incinerator residues

In this study, percolation and batch leaching tests were considered in order to characterize the behaviour of air pollution control (APC) residues produced in a municipal solid waste incinerator (MSWI) as a function of the liquid to solid ratio (L/S). This waste is hazardous, and taking into account their physical and chemical properties, leaching of contaminants into the environment is the main concern. In our work the leaching behaviour of toxic heavy metals (Pb, Zn, Cr, Ni and Cu) and inorganics associated with soluble salts (Na, K, Ca and Cl) was addressed. Although pH of the leaching solution is the most important variable, L/S may also play an important role in leaching processes. In our work, results from column and batch tests were compared in terms of concentration (mg/L) and releasing (mg/kg). The APC residues revealed to be hazardous according to both tests, and both Pb and Cl⁻ far exceeded the regulatory thresholds. The material exhibits high solubility, and when the liquid to solid ratio was high, more than 50% can be solubilised. The patterns of release may be in some cases availability or solubility controlled, and the former was easier to identify. When the results from column and batch experiments were compared by representing the cumulative released amounts (in mg/kg) as a function of L/S, both curves match for Zn, Ni, Cu, K, Na, Cl and Ca, but for Cr and Pb a significant difference was observed. In fact, the column experiments revealed that under percolation conditions it should be expected slow releasing of Pb along time. From this study, it can be concluded that the released amounts obtained in batch experiments for a certain L/S should be considered as the worst case for medium term. Some simple models proposed on the literature and based on local equilibrium assumption showed good fitting to experimental data for soluble species (non-reactive solutes).     

Methodology for quantification of waste generated in Spanish railway construction works

In the last years, the European Union (EU) has been focused on the reduction of construction and demolition (C&D) waste. Specifically, in 2006, Spain generated roughly 47million tons of C&D waste, of which only 13.6% was recycled. This situation has lead to the drawing up of many regulations on C&D waste during the past years forcing EU countries to include new measures for waste prevention and recycling. Among these measures, the mandatory obligation to quantify the C&D waste expected to be originated during a construction project is mandated. However, limited data is available on civil engineering projects. Therefore, the aim of this research study is to improve C&D waste management in railway projects, by developing a model for C&D waste quantification. For this purpose, we develop two equations which estimate in advance the amount, both in weight and volume, of the C&D waste likely to be generated in railway construction projects, including the category of C&D waste generated for the entire project.