Rotary Kiln Incineration III. An Indepth Study—Kiln Exit/Afterburner/Stack Train and Kiln Exit Pattern Factor Measurements During Liquid CCl4 Processing

Temperature and stable species concentration data are presented from various locations within a full-scale rotary kiln incinerator firing natural gas/carbon tetrachloride/air. The data are being collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop a more sophisticated understanding of and a predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. Non-uniformities in stable species and temperature exist for this particular kiln, at the kiln exit, under certain operating conditions. Flow perturbations from within the kiln were found to persist into the afterburner, but not into the stack. High destruction and removal efficiencies (DRE’s) were achieved under the operating conditions of these tests through adequate secondary combustion processing.     

Rotary Kiln Incineration IV. An Indepth Study— Kiln Exit,Transition and Afterburner Sampling During Liquid CCl4 Processing

Detailed temperature and stable species concentration data are presented from the kiln exit, transition section and afterburner of a full-scale incinerator facility firing natural gas/carbon tetrachloride/air. The data are collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop an understanding and predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. The data demonstrate that nonuniformities in stable species and temperature exist, under certain operating conditions, at the kiln exit in the vertical direction only. Measurements from the transition section indicate that non-uniformities may exist within this region under certain operating conditions. Flow perturbations from within the kiln can persist into the afterburner, although the degree of nonuniformity is substantially reduced compared to either the kiln or transition sections. High destruction and removal efficiencies were achieved under all operating conditions of these tests through a combination of kiln and secondary combustion processing.     

The use of anthracene as a model compound in a comparative study of hydrous pyrolysis methods for industrial waste remediation

Polycyclic aromatic hydrocarbons are very stable compounds and tend to bioaccumulate in the environment due to their high degree of conjugation and aromaticity. Hydrous pyrolysis is explored as a technique for the treatment of industrial water containing PAH, using anthracene as a model compound. The reactivity of anthracene under a range of temperatures and durations are studied in this paper. Aliquots of 1.0-10.0 mg of anthracene in a range of 1.0-5.0 mL of H₂O are subjected to hydrous pyrolysis under varied conditions of temperature, reagents and duration. The conditions include oxidising systems comprising distilled water, hydrogen peroxide and Nafion-SiO₂ solid catalyst in water; and reducing systems of formic acid and formic acid/Nafion-SiO₂/Pd-C catalysts to assess a range of redox reaction conditions. Oxygen in air played a role in some of the reaction conditions. Pyrolysed products were identified and quantified by the use of Gas Chromatography-Mass Spectrometry (GC-MS). The major products were anthrone, anthraquinone, xanthone from oxidation; and multiple hydro-anthracene derivatives from reductive hydogenation. The nature of reaction conditions influenced the extent of anthracene degradation. The products formed are more reactive (less stable) as compared to anthracene the starting material and will therefore be less persistent in the environment.     

Volatile nanoparticle formation and growth within a diluting diesel car exhaust

A major source of particle number emissions is road traffic. However, scientific knowledge concerning secondary particle formation and growth of ultrafine particles within vehicle exhaust plumes is still very limited. Volatile nanoparticle formation and subsequent growth conditions were analyzed here to gain a better understanding of "real-world" dilution conditions. Coupled computational fluid dynamics and aerosol microphysics models together with measured size distributions within the exhaust plume of a diesel car were used. The impact of soot particles on nucleation, acting as a condensational sink, and the possible role of low-volatile organic components in growth were assessed. A prescribed reduction of soot particle emissions by 2 orders of magnitude (to capture the effect of a diesel particle filter) resulted in concentrations of nucleation-mode particles within the exhaust plume that were approximately 1 order of magnitude larger. Simulations for simplified sulfuric acid-water vapor gas-oil containing nucleation-mode particles show that the largest particle growth is located in a recirculation zone in the wake of the car. Growth of particles within the vehicle exhaust plume up to detectable size depends crucially on the relationship between the mass rate of gaseous precursor emissions and rapid dilution. Chassis dynamometer measurements indicate that emissions of possible hydrocarbon precursors are significantly enhanced under high engine load conditions and high engine speed. On the basis of results obtained for a diesel passenger car, the contributions from light diesel vehicles to the observed abundance of measured nucleation-mode particles near busy roads might be attributable to the impact of two different time scales: (1) a short one within the plume, marked by sufficient precursor emissions and rapid dilution; and (2) a second and comparatively long time scale resulting from the mix of different precursor sources and the impact of atmospheric chemistry.     

Analysis of perfluorooctanoate (PFOA) and other perfluorinated compounds (PFCs) in the River Po watershed in N-Italy

C7-C11 perfluorinated carboxylates (PFACs) and perfluorooctansulfonate (PFOS) were analysed in selected stretches of the River Po and its major tributaries. Analyses were performed by solid-phase extraction (SPE) with Oasis HLB cartridges and methanol elution followed by LC-MS-MS detection using 13C-labelled internal standards. High concentration levels ( approximately 1.3 microg l(-1)) of perfluorooctanoate (PFOA) were detected in the Tánaro River close to the city Alessandria. After this tributary, levels between 60 and 337 ng l(-1) were measured in the Po River on several occasions. The PFOA concentration close to the river mouth in Ferrara was between 60 and 174 ng l(-1). Using the river discharge flow data in m3 s(-1) at this point (average approximately 920 m3 s(-1) for the year 2006), a mass load of approximately 0.3 kg PFOA per hour or approximately 2.6 tons per year discharged in the Adriatic Sea has been calculated. PFOS concentration levels in the Po River at Ferrara were approximately 10 ng l(-1).     

Chemisch-analytische Untersuchung von Arsenkampfstoffen und ihren Metaboliten

Arsenic containing chemical warfare agents (cwa) are persistent in the environment and continue to contaminte soil and ground water. In this paper the chemical rections of the cwa diphenylarsine chloride (CLARK I), phenylarsine dichloride (PFIFFIKUS), ethylarsine dichloride (DICK) and of chlorovinyl arsenic compounds (LEWISITE) are shown. The posibilities of the detection and determination of this cwa and their metabolites are presented.     

坦桑尼亚的可持续城市规划

本文概述坦桑尼亚可持续城市规划 .它考察城市活动的环境影响以及为推动对环境来说可持续城市发展而达成妥协和形成一致、合作和伙伴关系的方式 .环境规划与管理 (EPM)过程已在达累斯萨拉姆成功启动并在该国 9个城市得到同样应用 .     

Land Evaluation for Maize Based on Fuzzy Set and Interpolation

The objective of this article is to apply fuzzy set and interpolation techniques for land suitability evaluation for maize in Northern Ghana. Land suitability indices were computed at point observations using the Semantic Import (SI) model, whereas spatial interpolation was carried out by block kriging. Interpolated land suitability shows a high correlation (R2 = 0.87) with observed maize yield at the village level. This indicates that land suitability is closely related to maize yield in the study area. Membership functions were further used to assess the degree of limitation of land characteristics to maize. Sixty percent of the data has membership functions ranging from 0.23 for ECEC to 1.00 for drainage. ECEC, organic C, and clay are the major constraints to maize yield. The use of the fuzzy technique is helpful for land suitability evaluation, especially in applications in which subtle differences in soil quality are of a major interest. Furthermore, the use of kriging that exploits spatial variability of data is useful in producing continuous land suitability maps and in estimating uncertainties associated with predicted land suitability indices.