Honorary Memberships

Honorary Memberships are conferred by the Air Pollution Control Association on persons of widely recognized eminence in some part of the field of air pollution control or who have rendered especially meritorious service to the Association. Honorary Memberships were awarded this year to Dr. Leonard Greenburg and Mr. Milton Reizenstein, both past presidents of APCA.     

Improvement of Ambient Sulfur Dioxide Concentrations by Conversion from Low to High Stacks

A study of the “before” and “after” ground-level S0₂ concentrations near the Muskingum River Plant of the American Electric Power System shows that the conversion from low to high stacks has accomplished marked reductions in ambient concentrations. These reductions are in reasonable agreement with theoretical calculations and are most apparent within 5 km of the source. EPA Standards are now being met in this area despite the presence of the 1440 MW power plant burning 5% sulfur fuel with no treatment of the stack gas.     

The Use of Nahcolite Ore and Bag Filters For Sulfur Dioxide Emission Control

This paper describes some technical and economic aspects of the nahcolite ore injection process for the simultaneous removal of fly ash and sulfur oxides from stack gases. The process is capable of removing greater than 99% of the particulate matter and greater than 70% of the sulfur oxides present in such gases. In the process, nahcolite ore, a naturally occurring material containing 70 to 90% sodium bicarbonate, is ground to 90% passing through —200 mesh screens. Approximately 20% of the ground ore is used to precoat the filter bags in a baghouse filter while the remainder of the material is fed into the flue gas Just ahead of the baghouse. The flue gas is drawn through the baghouse by induced draft fans and sent up the stack. Most of the SO₂ and practically all of the fly ash in the flue gas can be removed as the gas passes through the filter bags. The spent nahcolite ore and fly ash are collected and conveyed to waste disposal as landfill, or alternatively processed for insolubilization by coprecipitation prior to landfilling. The technical feasibility of the process has been demonstrated in both bench scale and pilot scale engineering studies. Economic analyses performed for the cases of plants located in the midwest and southwest indicate lower capital costs for the nahcolite injection process when compared to wet scrubbing. On an annual cost basis, the nahcolite ore Injection process is comparable in cost to wet scrubbing for the case of the southwestern power plant, and somewhat more expensive for the case of the midwestern plant.     

Emission Control in Coking Operations By Use of Stage Charging

At the Clairton Coke Works of the United States Steel Corporation (the world’s largest coke plant), with coal charges of about 30,000 net tons per day, a system designated as “stage charging” has been developed for charging coal into the coke oven chamber without emissions to the atmosphere. The principles of the system are based on controlled sequential flow of the coal from the charging hoppers, during which the oven chamber is maintained under a very slight negative pressure condition by use of steam aspiration in the offtakes for on-the-main charging. The techniques are basic but require knowledge of the coal characteristics, adequate and properly maintained aspirating systems, including clean offtake piping, control of coal volume in the individual hoppers, and last, and probably most important, adherence by the operating crew to specific charging and leveling practices.     

Cooling Towers and the Environment

Measurements of natural draft cooling tower plume behavior, as well as meteorological variables, were obtained from aircraft flights near major power plants of the American Electric Power System. Persistence of the visible plume to great distances depends essentially on ambient humidity. Atmospheric stability at plume elevation was also important. Cooling tower-induced fog at ground-level was never observed in any of the tests, and aerodynamic downwash of the visible plume was absent also. The cooling towers did cause modification of natural clouds and they occasionally shadowed some local areas from the sun. Merging of the stack and cooling tower plumes was a common occurrence.     

Characterization of Particulates from Power Plants

The emphasis on participate control from industrial processes has been shifted recently towards fine particulates, having diameters less than 3 microns. There exists an urgent need for more scientific information of fine particle characterization.^1,2 Coal and oil fired power plants are among the largest anthropogenic point sources of particulate matter.³ Limited knowledge is available on particle size distribution and trace metal composition in power plant emissions.^4-7 The morphological properties of particle emissions have been largely neglected. In this report we present some information on particle characteristics for an oil-fired and coal-fired power plant.     

Interpretation of Meteorological Pollutant Roses in Areas Subject to Nocturnal Drainage Winds

The composition of aerosol particle products formed from the photochemical reaction of terpenes with NO_x and the chemical reaction of terpenes with ozone was determined using direct insertion probe/high resolution mass spectrometry. Samples of the aerosol particles generated from these gas phase reactions were collected on stainless steel disks using a specially-designed impactor. The samples were analyzed using computer-controlled high resolution mass spectrometry. The photochemical reaction of limonene with NO_x produced more than 30 reaction products in the aerosol phase. The major products identified included aldehydes, alcohols, acids, peroxides, and nitrate esters of alcohols, acids, and peroxides. In addition, there was evidence of dimeric and possibly trimeric reaction products. The composition of aerosol particle products formed from the dark reaction of ozone with limonene was determined and found similar to those products generated in the photochemical reaction, excluding the nitrated species. Aerosol concentrations were monitored using nephelometry which indicated a conversion of terpene to aerosol of 50% or greater for both the limonene and terpinolene reaction systems. The results show that direct insertion probe high resolution mass spectrometric technique has the capability for determining the composition of very polar and high molecular weight materials in aerosol particles. The composition of terpene aerosol particle products and the mass spectral data obtained from their analysis can be used in further studies to determine the importance of terpene aerosol particle formation in ambient air.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

Transmissometer Measurement of Participate Emissions from a Jet Engine Test Facility

The body of information presented in this paper is directed toward those individuals involved with handling hazardous materials, whether in actual use of such chemicals, or in monitoring atmospheric emissions. Although specifically relating experience in the design and testing of phosgene emission control equipment, it attempts to establish general guidelines for effectively dealing with emissions of hazardous materials. An approach for handling chemical pollutants having no established air quality emission standards is developed. The paper presents a technique for establishing process emissions at acceptably low levels to insure the health and safety of the general population as well as that of the process workers themselves. Methods, suitable for measuring phosgene at these low levels, have been investigated, and problems associated with such an investigation are discussed. While complete theoretical scrubber design criteria are beyond the scope of this paper, many of the "real world" problems which affected scrubber performance are presented. Finally, the practical aspects of process emissions control are illustrated by actual results from the system test.