Monitoring of the three organophosphate esters TBP,TCEP and TBEP in river water and ground water (Oder,Germany)

The behaviour of the three organophosphate esters tributyl phosphate (TBP), tris(2-chloroethyl)phosphate (TCEP) and tris(2-butoxyethyl)phosphate (TBEP) during infiltration of river water to ground water has been investigated. The monitoring site is the Oder River and the adjacent Oderbruch aquifer. From March 2000 to July 2001, 76 ground water samples from monitoring wells located close to the Oder River and nine river water samples were collected. Additionally, influent and effluent samples from local waste water treatment plants, one sample of rain water and samples of roof runoff were collected. All samples were analysed by solid-phase-extraction followed by gas chromatography/mass spectrometry. TBP, TCEP and TBEP were detected at mean values of 622 ng l(-1), 352 ng l(-1), and 2955 ng l(-1), respectively in municipal waste water effluents. This points to a major input of these compounds into the Oder River by municipal waste water discharge. The concentrations of TBP and TBEP decreased downstream the Oder River possibly due to aerobic degradation. TBP, TCEP and TBEP were detected in ground water influenced predominantly by bank-filtered water. This demonstrates a transport of organic compounds by river water infiltration to ground water. TBP, TCEP and TBEP were also detected in rain water precipitation, roof runoff and ground water predominantly influenced by rain water infiltration. This hints to an input of these compounds to ground water by dry and wet deposition after atmospheric transport. Organophosphate esters were also detected in parts of the aquifer at 21 m depth. This demonstrates low anaerobic degradation rates of TBP, TCEP and TBEP.     

Assessing land use impacts on flood processes in complex terrain by using GIS and modeling approach

A distributed hydrologic modeling and GIS approach is applied for the assessment of land use impact in the Steinsel sub-basin, Alzette, Grand-Duchy of Luxembourg. The assessment focuses on the runoff contributions from different land use classes and the potential impact of land use changes on runoff generation. The results show that the direct runoff from urban areas is dominant for a flood event compared with runoff from other land use areas in this catchment, and tends to increase for small floods and for the dry season floods, whereas the interflow from forested, pasture and agricultural field areas contributes to the recession flow. Significant variations in flood volume, peak discharge, time to the peak, etc., are found from the model simulation based on the three hypothetical land use change scenarios.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).     

Improvement of the BCR three step sequential extraction procedure prior to the certification of new sediment and soil reference materials

The Standards, Measurements and Testing Programme (formerly BCR) of the European Commission proposed a three-step sequential extraction procedure for sediment analysis, following extensive expert consultations and two interlaboratory studies. This scheme was recently used to certify the extractable trace element contents of a sediment reference material (CRM 601). Although this procedure offers a means to ensure the comparability of data in this field, some difficulties concerning the interlaboratory reproducibility still remain, and a new project is currently being conducted to determine the causes of poor reproducibility in the extraction scheme. The final objective of the project is the certification of new sediment and soil reference materials for their extractable contents of Cd, Cr, Cu, Ni, Pb and Zn. This paper presents the results of a small-scale interlaboratory study, which aimed to test a revised version of the extraction schemes by comparing the original and the modified protocols using the CRM 601 sample. This work offers an improvement to the BCR sequential extraction procedure through intercomparison exercises. This improved procedure will allow the obtaining of CRMs to validate analytical data in the analysis of soils and sediments, and it will also facilitate comparability of data in the European Union.     

Sampling Benthic Macroinvertebrates in a Large Flood-Plain River: Considerations of Study Design, Sample Size, and Cost

Estimation of benthic macroinvertebrate populations over large spatial scales is difficult due to the high variability in abundance and the cost of sample processing and taxonomic analysis. To determine a cost-effective, statistically powerful sample design, we conducted an exploratory study of the spatial variation of benthic macroinvertebrates in a 37 km reach of the Upper Mississippi River. We sampled benthos at 36 sites within each of two strata, contiguous backwater and channel border. Three standard ponar (525 cm²) grab samples were obtained at each site ('Original Design'). Analysis of variance and sampling cost of strata-wide estimates for abundance of Oligochaeta, Chironomidae, and total invertebrates showed that only one ponar sample per site ('Reduced Design') yielded essentially the same abundance estimates as the Original Design, while reducing the overall cost by 63%. A posteriori statistical power analysis ( = 0.05, = 0.20) on the Reduced Design estimated that at least 18 sites per stratum were needed to detect differences in mean abundance between contiguous backwater and channel border areas for Oligochaeta, Chironomidae, and total invertebrates. Statistical power was nearly identical for the three taxonomic groups. The abundances of several taxa of concern (e.g., Hexagenia mayflies and Musculium fingernail clams) were too spatially variable to estimate power with our method. Resampling simulations indicated that to achieve adequate sampling precision for Oligochaeta, at least 36 sample sites per stratum would be required, whereas a sampling precision of 0.2 would not be attained with any sample size for Hexagenia in channel border areas, or Chironomidae and Musculium in both strata given the variance structure of the original samples. Community-wide diversity indices (Brillouin and 1-Simpsons) increased as sample area per site increased. The backwater area had higher diversity than the channel border area. The number of sampling sites required to sample benthic macroinvertebrates during our sampling period depended on the study objective and ranged from 18 to more than 40 sites per stratum. No single sampling regime would efficiently and adequately sample all components of the macroinvertebrate community.     

Background Levels of Metals in Soils, McMurdo Station, Antarctica

McMurdo Station is the largest research station in Antarctica, with a population that ranges each year from 250 to 1200 people. Because of its size and 40-year history of use, a number of locations around the station have become contaminated with wastes. Soils and sediments in these areas have been shown to contain elevated levels of petroleum-related products, PCBs, other organics, and metals. While some remedial investigations have been conducted, background levels of metals in soils have not been determined. This paper reports on background levels of metals in a natural basalt-derived soil (gray soil) and scoria (soft porous rock used as fill, red soil) near McMurdo Station using two fundamentally different analytical procedures, concentrated acid extraction/analysis and total metals. These data facilitate determining the extent and levels of metal contamination near McMurdo Station and provide reference levels of metals for comparison with existing and future remediation data. There were statistically significant differences between metals concentrations in both gray and red soils, and no correlations between the level of extracted versus total metal. Generally, only a small fraction of a metal was extractable.     

Soil properties and crop productivity as influenced by flyash incorporation in soil

Field experiments were carried out during 1996–97at Gulawathi, Muthiani and Salarpur Villages, IARI Farm, NewDelhi and NCPP Campus, Dadri to evaluate changes in soilcharacteristics and growth of wheat (Triticum aestivum L.),mustard (Brassica juncea L.), lentil (Lence esculentaMoench.), rice (Oryza sativa L.) and maize (Zea mays L.) byvarying amounts of flyash addition (up to 50t ha^-1) in soils atsowing/transplanting time of crops. Flyash addition in areasadjoining NCPP Thermal Power Plant, Dadri, Ghaziabad, U.P.ranged from 5–12 t ha^-1 yr^-1 in 1995–96. Shoot and root growthand yield of test crops at different locations after flyashincorporation resulted in beneficial effects of flyashaddition in most cases. The silt dominant texture of flyashimproved loamy sand to sandy loam textures of the surfacesoils at the farmers' fields. The increased growth in yield ofcrops with flyash incorporation was possibly due tomodifications in soil moisture retention and transmissioncharacteristics, bulk density, physico-chemical characterssuch as pH and EC and organic carbon content. The response offlyash addition in the soil on soil health and cropproductivity needs to be evaluated on long-term sustainableaspects.     

Flue gas treatability studies: a tool for techno-economic control of industrial air pollution

Air pollution problems in developing countries have gained larger fraction in the last decade especially due to non functioning and non implementation of effective air pollutioncontrol devices in industries. In industrial wastewater management, adequate treatability studies are conducted to arrive at a techno-economic treatment option. However no suchstudies were done for reducing air pollution or emission fromindustries until now in India. Little information was availableabout such studies in other countries. This article provides information about a novel technique known asflue gas treatability studies and to undertake such studies, a pilot scale system is installed in Air Pollution Control Divisionof M/s National Environmental Engineering research Institute, NEERI, Nagpur-20, India. This study is a tool for techno-economicselection of air pollution control systems specially for small/medium scale industrial emissions.     

A Metamodeling Approach for Integrated Assessment of Air Quality Policies

A method is proposed to build integrated models (also called Metamodels) aimed at quantifying the economic efficiency of air quality policies. This Metamodeling approach is based on the coupling of two complementary models, that operate at different scales in space and time, and which represent the economic and the physical and chemical processes, respectively. The joint consideration of the physico-chemical and techno-economic structure of the pollution control problems permits a comprehensive evaluation of air pollution abatement strategies. The motivating pollution control problems include urban-regional air quality management through efficient energy and traffic control policies. A pilot study, exploiting data collected in the Geneva canton (Switzerland), is used to demonstrate the potential of the approach.     

The Influence of pH on Mobility of Heavy Metals from Municipal Solid Waste Incinerator Fly Ash

Incineration has become one of the principal methods for municipal solid waste disposal particularly in all large cities throughout the world. Currently, the municipal solid waste incinerator fly ashes (MSWIF) are disposed of by landfill. The metal speciation of cadmium (Cd), chromium (Cr), copper (Cu), lead (Pb), and zinc (Zn) in MSWIF after been extracted with water at different pH values were examined using a sequential extraction procedure. The extraction sequence was as follows: (1) Exchangeable (NaOAc, pH 8.2), (2) Bound to Carbonates (NaOAc, pH 5.0), (3) Bound to metal oxides (HONH3Cl), (4) Bound to organic matters (HNO3, H2O2), and (5) Residual (HNO3, HCl, H2O2, HF, 1:3:1:3). The heavy metal contents in the extraction solutions were determined by inductively coupled plasma atomic emission spectrometry. The heavy metal concentrations in the different fractions obtained by sequential extraction show distinct distribution trends. The extractable fraction ranges from 25.5 to 88% of the total element content. With the pH of the extractant fall below the neutral and acidic ranges, the concentrations of heavy metals rise substantially due to the released of metals bound to carbonate fraction.