基于SSM方法的黑龙江省入境旅游产业结构分析

以相关入境旅游统计数据为基础,运用转移—份额分析法,对2002—2007年黑龙江省入境旅游产业结构进行了分析。结果表明,黑龙江省入境旅游产业发展速度高于全国水平,产业结构较好,但总体竞争力不强。在此基础上,针对产业中的优势部门、增长部门和劣势部门提出了相应的对策和建议。     

饱和膨润土复合颗粒吸附剂吸附的重金属离子的固定及其再生

采用Na_2S化学再生法对吸附Fe~(2+)、Mn~(2+)、Cu~(2+)和Zn~(2+)饱和的膨润土-钢渣复合颗粒吸附剂分别进行重金属离子的固定及其再生实验研究,探究该吸附剂吸附的重金属离子的固定问题及其再生的可能性和多次再生后的吸附效果,同时根据SEM图进一步揭示固定、再生机理。结果表明:在对Fe~(2+)的固定、再生实验中,可形成Fe S沉淀而实现固定,但再生后再吸附时,膨润土复合颗粒中蒙脱石结构改变使得颗粒坍塌变成粉末状,因此,吸附Fe~(2+)饱和的膨润土复合颗粒吸附剂不适合用Na_2S再生;而对Mn~(2+)、Cu~(2+)和Zn~(2+)的固定、再生实验中,均可形成S化物沉淀而实现固定,颗粒结构未改变,经过3次再生后,吸附剂对Mn~(2+)、Cu~(2+)和Zn~(2+)的去除率还可达到94.22%、83.2%和76.30%,远比未经再生的吸附剂吸附效果好,同时,由SEM表征分析进一步揭示:Na_2S再生溶液既可使重金属离子形成MS沉淀固定,又可使复合颗粒吸附剂获得再生,实现了同步固定、再生的目的,且吸附剂经多次再生后吸附效果保持良好。     

生物絮凝剂产生菌群发酵特性及动力学

从土壤中分离、筛选得到2株具有协同发酵的微生物絮凝剂产生菌。通过单因素实验考察了碳源、氮源、不同C/N等多种发酵条件对复合菌株产絮的影响,并对复合菌株的生长动力学进行了研究。当碳源为蔗糖、氮源为草酸铵、C/N为30∶1,pH=7.0、在30℃,160 r/min的摇床速度下培养24 h,其发酵液对4 g/L的高岭土的悬浊液的絮凝率达到99.3%。根据Logistic方程,得到复合型生物絮凝剂产生菌群的生长动力学模型与实验数据能较好地拟合,基本反映了复合菌群生长的动力学特征。     

Bioaccumulation and depuration of anthracene in Penaeus monodon (Fibricius) through food ingestion

Understanding on the bioaccumulation and depuration of PAHs (polycyclic aromatic hydrocarbons) in Penaeus monodon is important in seafood safety because it is one of the most popular seafood consumed worldwide. In this study, we used anthracene as the precursor compound for PAHs accumulation and depuration in the shrimp. Commercial feed pellets spiked with anthracene were fed to P. monodon. At 20 mg kg⁻¹ anthracene, P. monodon accumulated 0.1% of the anthracene from the feed. P. monodon deputed the PAH two times faster than its accumulation. The shrimp reduced its feed consumption when anthracene content in the feed exceeded 20 mg kg⁻¹. At 100 mg kg⁻¹ anthracene, P. monodon started to have necrosis tissues on the posterior end of their thorax. The bioaccumulation factor (BAF), uptake rate constant (k₁) and depuration rate constant (k₂) of anthracene in P. monodon were 1.15 × 10⁻³, 6.80 × 10⁻⁴ d⁻¹ and 6.28 × 10⁻¹ d⁻¹, respectively. The depuration rate constant is about thousand times higher than the uptake rate constant and this indicated that this crustacean is efficient in depurating hydrocarbons from their tissue.     

PBDD/F impurities in some commercial deca-BDE

The study presented the concentrations and distributions of polybrominated dibenzo-p-dioxins and polybrominated dibenzofurans (PBDD/Fs) as impurities in some commercial decabromodiphenyl ether (DBDE) mixtures that were produced by several manufacturers. The total concentrations of 12 2,3,7,8-substituted tetra- to octa-BDD/F congeners were found to be in the range of 3.4-13.6 (mean 7.8) μg/g, averagely accounting for 99% of total PBDD/Fs. OBDF was the prevailing congener, followed by 1,2,3,4,6,7,8-HpBDF. In addition, OBDD and 1,2,3,4,7,8-HxBDF were also obviously detectable. The total concentrations of PBDD/Fs varied both between the manufacturers and between the lots. On the basis of the global demand for the commercial DBDE in 2001, the annual potential emissions of PBDD/Fs were calculated coarsely to be 0.43 (range: 0.21-0.78) tons. The major dioxin congeners, OBDF and 1,2,3,4,6,7,8-HpBDF, presenting in DBDE, were estimated to be formed from BDE-209, BDE-206, and/or BDE-207 via an intra-molecular elimination of Br₂/HBr.     

The changes of nitric oxide production during the growth of Microcystis aerugrinosa

This study characterized the changes of nitric oxide (NO) production during the growth of Microcystis aerugrinosa, a cyanobacterium which usually cause cyanobacterial blooms. Results showed a drastic NO release accompanying with cell density and Chl-a content sharp rises when M. aerugrinosa grew from fifth day to sixth day. Moreover, high N:P ratio accelerated the cyanobacterial growth and NO burst. Sodium nitroprusside, an exogenous NO donor, promoted M. aerugrinosa growth with the optimal concentration of 0.1 mg/L. Experiments by supplementing with sodium nitrite and l-arginine demonstrated NO production in M. aerugrinosa cells was mainly through nitrate reductase (NR) pathway while minorly through NO synthase pathway. All these data suggested M. aerugrinosa produced increasing NO during its growth mainly by NR pathway, during which NO positively regulated the growth of M. aerugrinosa.     

Performance of hybrid vertical up- and downflow subsurface flow constructed wetlands in treating synthetic high-strength wastewater

The performance and temporal variation of hybrid vertical-subsurface flow constructed wetlands (VFCWs) in response to two-stage combinations of vertical upflow (VUF) and vertical downflow (VDF) were analyzed in this research. The results of high carbon (C) treatment and high nitrogen (N) treatment were similar. The Lythrum salicaria treatment showed higher removal efficiency than CWs planted with Acorus calamus. Under high C- and N-loading treatments, the optimum two-stage combination was VDF-VUF VFCWs planted with A. calamus. Furthermore, the highest nutrient removal efficiencies were achieved in late summer (July and August) and early autumn (September). The chemical oxygen demand and total nitrogen removal efficiencies were significantly affected (P?<?0.05) by season, system, and wetland plant.     

用味精生产废水培养好氧颗粒污泥

以厌氧颗粒污泥为接种污泥,采用味精生产废水进行培养,在SBR中以逐渐降低污泥沉淀时间的方法成功培养出好氧颗粒污泥。实验结果表明：污泥接种65 d后,出现细小的好氧颗粒污泥,呈黄褐色,95 d后颗粒污泥趋于成熟,粒径达0.6 mm左右,且周围存在大量原生动物;运行95 d后MLSS提高至8.00 g/L,SVI降至30.00 mL/g左右;成熟后的好氧颗粒污泥对味精生产废水中的COD和NH₃-N具有良好的去除效果,出水COD和ρ（NH₃-N）分别为80 mg/L和2 mg/L左右。     

膨润土复合新型吸附剂处理含Mn~(2+)废水

针对废水中Mn2+难去除问题,利用经高温焙烧制备的膨润土-粉煤灰复合新型吸附剂对废水中的Mn2+进行吸附处理实验研究。研究了新型吸附剂在不同的吸附时间、pH、初始Mn2+浓度条件下对Mn2+的吸附去除效果影响、Fe2+、Mn2+共存时竞争吸附特性以及吸附Mn2+的吸附性能和反应动力学。实验结果表明,新型吸附剂处理Mn2+浓度为35 mg/L的废水,在温度25℃、转速100 r/min、投加量20 g/L、吸附时间120 min、pH≥7时反应条件最佳,Mn2+的去除率均可达到90%以上;Fe2+、Mn2+共存时,存在竞争吸附,Fe2+会被优先选择吸附去除,Fe2+的存在会影响Mn2+的去除效果;膨润土复合新型吸附剂对Mn2+的吸附行为符合Langmuir等温吸附模型和准二级动力学模型。新型吸附剂对废水中的Mn2+有很好的去除效果,而且能有效解决膨润土不易固液分离问题,可作为含Mn2+废水高效、廉价、环保的水处理吸附剂。     

Fine particulate speciation profile and emission factor of municipal solid waste incinerator established by dilution sampling method

In this study, fine particulate matter (PM_2.5) emitted from a municipal solid waste incinerator (MSWI) was collected using dilution sampling method. Chemical compositions of the collected PM_2.5 samples, including carbon content, metal elements, and water-soluble ions, were analyzed. Traditional in-stack hot sampling was simultaneously conducted to compare the influences of dilution on PM_2.5 emissions and the characteristics of the bonded chemical species. The results, established by a dilution sampling method, show that PM_2.5 and total particulate matter (TPM) emission factors were 61.6 ± 4.52 and 66.1 ± 5.27 g ton-waste^?1, respectively. The average ratio of PM_2.5/TPM is 0.93, indicating that more than 90% of PM emission from the MSWI was fine particulate. The major chemical species in PM_2.5 included organic carbon (OC), Cl^?, NH₄⁺, elemental carbon (EC) and Si, which account for 69.7% of PM_2.5 mass. OC was from the unburned carbon in the exhaust, which adsorbed onto the particulate during the cooling process. High Cl^? emission is primarily attributable to wastes containing plastic bags made of polyvinyl chloride, salt in kitchen refuse and waste biomass, and so on. Minor species that account for 0.01–1% of PM_2.5 mass included SO₄^2-, K⁺, Na, K, NO₃^?, Al, Ca²⁺, Zn, Ca, Cu, Fe, Pb, and Mg. The mean ratio of dilution method/in-stack hot method was 0.454. The contents of water-soluble ions (Cl^?, SO₄^2-, NO₃^?) were significantly enriched in PM_2.5 via gas-to-particle conversion in the dilution process. Results indicate that in-stack hot sampling would underestimate levels of these species in PM_2.5.

Implications: PM_2.5 samples from a municipal solid waste incinerator (MSWI) were collected simultaneously by a dilution sampling technique and a traditional in-stack method. PM_2.5 emission factors and chemical speciation profiles were established. Dilution sampling provides more reliable data than in-stack hot sampling. The results can be applied to estimate the PM_2.5 emission inventories of MSWI, and the source profile can be used for contribution estimate of chemical mass balance modeling.