Alternating skimming flow over a stepped spillway

The study of stepped spillways in laboratory scales has been essentially focused on two separated sub-regimes within skimming flow. In this paper we investigate the appearance of an unclassified alternating skimming flow regime in a 0.5 m wide stepped spillway which does not fit on these earlier definitions, and which does not occur in a 0.3 m wide spillway. Our aim is to explain the genesis of this unclassified flow which is visualised in the physical stepped spillway, by using 3D numerical modelling. Flow depths and velocities are measured using an ultrasonic sensor and Bubble Image Velocimetry in the wider flume (0.5 m). The numerical model is validated with the experimental data from the 0.5 m wide spillway. After validation, the channel width of the same numerical model is reduced to 0.3 m wide spillway in order to characterise (compare) the case without (with) alternating skimming flow. Both cases are solved using Reynolds-Averaged Navier–Stokes equations together with the Volume-of-Fluid technique and SST k-\(\omega\) turbulence model. The experimental results reveal that the alternating skimming flow regime is characterised by an evident seesaw pattern of flow properties over consecutive steps. In turn, the numerical modelling clarified that this seesaw pattern is due to the presence of a complex system of cross waves along the spillway. These cross waves are also responsible for a mass and momentum exchange in the transversal direction and for the formation of the alternating skimming flow in the spillway.     

Behavior of Cellulose Reinforced Cross-Linked Starch Composite Films Made with Tartaric Acid Modified Starch Microparticles

Tartaric acid modified starch microparticles (TA-SM) previously obtained using the dry preparation technique were introduced as filler within glycerol plasticized-corn starch (GCS), the composites being prepared by casting process. The effects of cellulose addition within the TA-SM-GCS matrix on the structure, surface properties and water sorption, as well as mechanical and thermal properties of starch-based composite films were investigated. The water resistance and thermal stability were slightly improved through addition of high content of cellulose due to the inter-component H-bonding between components. The evaluation of mechanical properties evidenced a significant increase of the tensile strength of the composites with increasing the content level of cellulose.     

Integrated approach of environmental impact and risk assessment of Rosia Montana Mining Area, Romania

The environmental impact assessment of mining sites represents nowadays a large interest topic in Romania. Historical pollution in the Rosia Montana mining area of Romania caused extensive damage to environmental media. This paper has two goals: to investigate the environmental pollution induced by mining activities in the Rosia Montana area and to quantify the environmental impacts and associated risks by means of an integrated approach. Thus, a new method was developed and applied for quantifying the impact of mining activities, taking account of the quality of environmental media in the mining area, and used as case study in the present paper. The associated risks are a function of the environmental impacts and the probability of their occurrence. The results show that the environmental impacts and quantified risks, based on quality indicators to characterize the environmental quality, are of a higher order, and thus measures for pollution remediation and control need to be considered in the investigated area. The conclusion drawn is that an integrated approach for the assessment of environmental impact and associated risks is a valuable and more objective method, and is an important tool that can be applied in the decision-making process for national authorities in the prioritization of emergency action.     

Adsorption of Remazol Red 198 onto magnetic N-lauryl chitosan particles: equilibrium, kinetics, reuse and factorial design

Purpose

The discharge of colored effluents from industries is an important environmental issue and it is indispensable to remove the dyes before the water gets back to the rivers. The magnetic adsorbents present the advantage of being easily separated from the aqueous system after adsorption by positioning an external magnetic field.

Methods

Magnetic N-lauryl chitosan (L-Cht/??-Fe₂O₃) particles were prepared and characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, transmission electron microscopy, and vibrating sample magnetometry. Remazol Red 198 (RR198) was used as a reactive dye model for adsorption on L-Cht/??-Fe₂O₃. The adsorption isotherms were performed at 25°C, 35°C, 45°C, and 55°C and the process was optimized using a 2³ factorial design (analyzed factors: pH, ionic strength, and temperature). The desorption and regeneration studies were performed in a three times cycle.

Results

The characterization of the material indicated that the magnetic particles were introduced into the polymeric matrix. The pseudo-second order was the best model for explaining the kinetics and the Langmuir?CFreundlich was the best-fitted isotherm model. At room temperature, the maximum adsorption capacity was 267?mg?g^?1. The material can be reused, but with a decrease in the amount of adsorbed dye.

Conclusions

L-Cht/??-Fe₂O₃ is a promising material to remove RR198 and probably other similar reactive dyes from aqueous effluents.     

Protective effects of thymoquinone and diallyl sulphide against malathion-induced toxicity in rats

Environmental Science and Pollution Research - Malathion is a potent organophosphate insecticide that inhibits acetylcholinesterase (AChE) enzyme. Our experimental objective was to investigate the...     

Investigation of heavy metal content of Turkish tobacco leaves, cigarette butt, ash, and smoke

A procedure for the determination of cadmium, copper, manganese, and zinc in Turkish tobaccos, which were of different origins, years, and grades, and in the butt, ash, and smoke, which were obtained by smoking the cigarettes that were prepared manually from the said tobaccos in a smoking apparatus, was devised as proposed. The collected samples were digested by wet ashing technique by using HNO₃-HClO₄ and were analyzed by flame atomic absorption spectrometry with satisfactory recoveries (94 % to 98 %). The regression coefficients were above 0.99, and the detection limits were in the range of 0.03–0.12 mg/L^?1. The performance and accuracy of the method was tested by analyzing “Certified Reference Material GBW 08501-Peach Leaves.” The determined values were in agreement with the standard values for the heavy metals analyzed. Thus, it was concluded that the developed method could offer a wide range of application for establishing a relationship between the makeup and composition of tobacco plant, products, ash, smoke, and smoking.     

Alkali-silica reactions of mortars produced by using waste glass as fine aggregate and admixtures such as fly ash and Li2CO3

Use of waste glass or glass cullet (GC) as concrete aggregate is becoming more widespread each day because of the increase in resource efficiency. Recycling of wastes is very important for sustainable development. When glass is used as aggregate in concrete or mortar, expansions and internal stresses occur due to an alkali-silica reaction (ASR). Furthermore, rapid loss in durability is generally observed due to extreme crack formation and an increase in permeability. It is necessary to use some kind of chemical or mineral admixture to reduce crack formation. In this study, mortar bars are produced by using three different colors of glass in four different quantities as fine aggregate by weight, and the effects of these glass aggregates on ASR are investigated, corresponding to ASTM C 1260. Additionally, in order to reduce the expansions of mortars, 10% and 20% fly ash (FA) as mineral admixture and 1% and 2% Li(2)CO(3) as chemical admixture are incorporated by weight in the cement and their effects on expansion are examined. It is observed that among white (WG), green (GG) and brown glass (BG) aggregates, WG aggregate causes the greatest expansion. In addition, expansion increases with an increase in amount of glass. According to the test results, it is seen that over 20% FA and 2% Li(2)CO(3) replacements are required to produce mortars which have expansion values below the 0.2% critical value when exposed to ASR. However, usages of these admixtures reduce expansions occurring because of ASR.     

聚苯乙烯磺酰肼基二硫代甲酸盐树脂功能化程度的分光光度测定

用改进的方法合成了对甲苯磺酰肼基二硫代甲酸钾。以它作模型化合物,在酸性条件下加热解,放出二硫化碳,被二乙胺及醋酸铜的混合液吸收,生成黄色荒氨酸铜,在４３０ｎｍ波长比色,从而建立了定量测定磺酰肼基二硫代甲酸基团的方法。     

Environment as Politics: Framing the Cerattepe Protest in Twitter

Environmental protests across the globe are often studied with a particular focus on their environmental aspects, but these protests are also embedded in a local political setting shaped by governmental policies. Recent environmental protests in Turkey, which appear to be based on ecological grievances, have developed as a response to political decisions that gave priority to economic development and national interests over environmental concerns. This study examines the political character of the environmental protest in Cerattepe, and focuses on the framing practices of its players in order to see if their motivations transcended environmental concerns. The research combines framing with network analysis, and studies the propagation of frames through Twitter. It has been found that the political economic aspects became predominant in the protest network, while the frames fostered dense connections between activist groups.     

Meiobenthic nematode Oncholaimus campylocercoides as a model in laboratory studies: selection,culture, and fluorescence microscopy after exposure to phenanthrene and chrysene

Environmental Science and Pollution Research - Numerous studies have focused on the response of meiofauna after exposure to polycyclic aromatic hydrocarbons (PAHs), but none has been devoted to...