A new device for measuring fluctuations in plant stem diameter: Implications for monitoring plant responses

An electrical device capable of continuously measuring micronsized changes in stem diameter of woody and herbaceous plants is described. Fumigation of sunflowers with automotive exhaust was used to test the ability of the device to detect short-term plant responses.     

Integration of modeling,monitoring and laboratory observation to determine reasons for air quality violations

An attempt was made to explain ambient air quality violations in the vicinity of industrial plants. Micrometeorology, diffusion calculaations, ambient readings, and plant engineering data are all taken into consideration to ascertain whether the plant is or is not the principal offender.Scrutiny of hi-vol filters using scanning electron microscopy for particle size analysis and particle chemical make-up as an assessment technique is also described.Case histories using the above analytical techniques are discussed.Presented at the 16th National Conference on Energy and the Environment, May 23, 1979     

Further studies using X-ray fluorescence to sample lead contaminated carpeted surfaces

The sampling of carpeted surfaces to test for lead contamination primarily focuses upon vacuum techniques. Vacuum sampling techniques, however, require time-consuming, expensive laboratory analysis of the dusts obtained and are unable to determine total lead load on the carpet. X-ray fluorescence (XRF) analysis is an on-site, inexpensive, non-destructive, quick technique for predicting metals levels in a variety of media, such as water, soil, filter paper and painted surfaces. A 1992 study of the feasibility of XRF to analyze for lead and soil loadings on carpeted surfaces indicated that XRF can detect lead at a low enough level to warrant further study. This paper expands this earlier study and developes lead and soil loading calibration curves for three different carpet types based upon XRF lead L-beta peak areas and XRF iron and barium K-alpha peak and background areas. Results indicate that variation in the data can be reduced through modifications of the XRF analysis technique, thus reducing the statistically determined detection level, and that carpet type does affect the calibration. Detection levels of approximately 70 mg/m² for lead and 5 g/m² for soil were obtained. Overall, good agreement was found between results of this study and the earlier one. XRF shows excellent potential for quantitative analysis of lead on carpeted surfaces.     

Ammonia uptake by plants

The paper considers the methodology and results of experimental determination of dry deposition and ammonia uptake by isolated plant leaves. Analytical expressions are proposed which allow a transition from rates obtained in an isolated chamber to dry ammonia deposition by standing crops leaves.     

Field scale variability of cadmium and zinc in soil and barley

CaCl₂-extractable soil Cd and Zn contents have been suggested as a measure of bioavailability. To investigate the ability of this measure to reflect spatial patterns of Cd and Zn concentrations in barley (Hordeum vulgare L.) in an arable field, plant and soil samples were taken from a 0.5 ha area sandy soil contaminated with Cd and Zn. Cd and Zn contents in barley and yield were spatially variable. Yield was low, which may have been caused by Zn toxicity or atrazine turnover. For Cd, CaCl₂-extractable soil contents explained only 17% of the variation in Cd contents in grain, and for Zn no significant correlation was observed. Nevertheless, surface plots of CaCl₂-extractable soil contents and contents of barley grain illustrated their corresponding spatial patterns. Despite the poor linear correlation between CaCl₂-extractable soil-Cd and grain-Cd, a stochastic model for long term behaviour of Cd in field soils predicted observed variability in Cd contents of barley grain well from spatial variability of soil pH and organic matter content. The probabilistic model predicted behaviour of Cd in terms of probability, and was more appropriate than the deterministic approach.     

Organochlorine contaminant concentrations in caddisfly adults (Trichoptera) collected from great lakes connecting channels

Pennsylvania-style light traps were used to capture adult Trichoptera from the St. Marys, St. Clair, Detroit and Niagara rivers, Canada. Adequate biomass was acquired in single, 2-h collections to permit triplicate gas chromatographic analyses of 1–4 g samples for 36 organochlorine contaminants. Contaminant levels varied unpredictably but relatively little among samples taken at monthly intervals over the summer. Samples collected simultaneously from the two sides of the Detroit R. reflected local sediment contaminant patterns, suggesting limited dispersal by adults. Genus-specific differences in contaminant concentrations within the Hydropsychidae and Leptoceridae probably reflect differences in larval habitats and manner of feeding. Contaminant concentrations and relative composition paralleled published reports of contaminants in sediments from collection locations. St. Marys R. caddisflies contained contaminant levels indistinguishable from samples collected at reference sites. St. Clair R. samples contained high levels of compounds associated with petrochemical industries located in the river's upstream reaches. High levels of polychlorinated biphenyls (PCBs) and most other contaminants in Detroit R. samples reflected industrial loadings near Detroit, Michigan. Niagara R. samples contained elevated concentrations of PCBs and pesticides. Cluster analysis grouped samples into five clusters each with unique contaminant composition. These also corresponded to geographic origin: St. Marys, St. Clair, Detroit and upper and lower Niagara rivers. The relative ease of collection and consistent results obtained render adult Trichoptera potentially valuable candidates for surveys of aquatic contamination over a broad range of geographical and ecological conditions.     

Patchy distributions: Optimising sample size

A method for estimating sample size which does not require an a priori definition of desired precision, or the assumption that the population is normally distributed with constant variance, has recently been proposed. This paper discusses this method and presents five modifications which make the method easier to use and reduce the probability of estimating a larger sample size than is actually required. The method is extended and used to estimate the mean abundance of patchily distributed benthic organisms. The technique can be used to guide the design of any environmental sampling programme, be it physical, chemical or biological, where comparisons between times and/or locations are required. Trade-offs between numbers of replicates and numbers of levels/sites are discussed.     

Partitioning of mercury onto suspended sediments in estuaries

Radiochemical partitioning experiments using 203Hg have been undertaken with mixtures of river, seawater and sediment samples taken from three geochemically contrasting UK estuaries: the Plym, Beaulieu and Mersey. Species of dissolved Hg were determined using reversed-phase C18 chelating columns and particulate species were determined by sequential leaching with 1 M NH4OAc and 1 M HCl. Mercury had a high particle reactivity with partition coefficients, KDs, ranging from 10(4) to 5 x 10(5) ml g(-1), depending on salinity, the chemical composition of the end-member waters, and on the physico-chemical characteristics of the sediment. Dissolved organic matter present in the waters (humic substances and/or anthropogenic compounds) was found to be the main factor governing the forms of dissolved Hg and their reactivity. From the spiked 203Hg, up to 95% of the dissolved metal was retained on the C18 columns for the Mersey waters, whereas this fraction was < 60% in the Plym and Beaulieu waters. Quasi-irreversible adsorption of Hg onto particles from each estuary was observed over a time-scale of a few hours and < 20% of total particulate Hg was released by the sequential leach. In this paper, physico-chemical processes are proposed to explain the estuarine behaviour of Hg and the results are discussed in terms of Hg availability in estuarine systems.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).