Assessment of control strategies for reducing volatile organic compound emissions from the polyvinyl chloride wallpaper production industry in Taiwan

This study attempts to assess the effectiveness of control strategies for reducing volatile organic compound (VOC) emission from the polyvinyl chloride (PVC) wallpaper production industry. In Taiwan, methyl ethyl ketone, TOL, and cyclohexanone have comprised the major content of solvents, accounting for approximately 113,000 t/yr to avoid excessive viscosity of plasticizer dioctyl phthalate (DOP) and to increase facility in working. Emissions of these VOCs from solvents have caused serious odor and worse air quality problems. In this study, 80 stacks in five factories were tested to evaluate emission characteristics at each VOC source. After examining the VOC concentrations in the flue gases and contents, the VOC emission rate before treatment and from fugitive sources was 93,000 and 800 t/yr, respectively. In this study, the semiwet electrostatic precipitator is recommended for use as cost-effective control equipment.     

Wet air oxidation of a reactive dye solution using CoAlPO(4)-5 and CeO(2) catalysts

Wet air oxidation of a prepared reactive dye solution was performed to assess the efficacy of CoAlPO(4)-5 and CeO(2) as catalysts in the reaction. Via adsorption and oxidation of dye, CoAlPO(4)-5 effectively decreased American Dye Manufacturers Institute and chemical oxygen demand (COD) values in the dye solution. At a reaction temperature of 135 degrees C and an applied pressure of 1.0 MPa, color and COD removal were as high as 95% and 90%, respectively, after 2 h. Active sites on the outer surface of CoAlPO(4)-5 are responsible for adsorption and decomposition of dye while active sites in the pores dominate further destruction and oxidation of intermediate products. Since the outer surface only represents a minor part of the total surface, the color removal does not increase appreciably with loading of CoAlPO(4)-5. The CeO(2) catalyst, calcined from cerium chloride under high thermal impact (type A CeO(2)) was very effective in removing color and COD from the solution. This catalyst demonstrated near 100% color removal at temperatures above 135 degrees C and the COD removal could be above 95% at 165 degrees C. With both CoAlPO(4)-5 and CeO(2) catalysts, COD rose and then fell back during the reaction, a feature typical of a consecutive reaction. In contrast to prepared CeO(2), a commercial CeO(2) did not exhibit any catalytic ability for the removal of color and COD. The durability of both CoAlPO(4)-5 and prepared CeO(2) is considered to be fair.     

Does safety climate moderate the influence of staffing adequacy and work conditions on nurse injuries?

PROBLEM: Hospital nurses have one of the highest work-related injury rates in the United States. Yet, approaches to improving employee safety have generally focused on attempts to modify individual behavior through enforced compliance with safety rules and mandatory participation in safety training. We examined a theoretical model that investigated the impact on nurse injuries (back injuries and needlesticks) of critical structural variables (staffing adequacy, work engagement, and work conditions) and further tested whether safety climate moderated these effects. METHOD: A longitudinal, non-experimental, organizational study, conducted in 281 medical-surgical units in 143 general acute care hospitals in the United States. RESULTS: Work engagement and work conditions were positively related to safety climate, but not directly to nurse back injuries or needlesticks. Safety climate moderated the relationship between work engagement and needlesticks, while safety climate moderated the effect of work conditions on both needlesticks and back injuries, although in unexpected ways. DISCUSSION AND IMPACT ON INDUSTRY: Our findings suggest that positive work engagement and work conditions contribute to enhanced safety climate and can reduce nurse injuries.     

静电基本参数的测试原理

静电测试是整个静电防护工程中不可或缺的组成部分,也是静电防护设计和管理的依据.本文主要介绍了静电基本参数中的静电电位、静电电容和静电电量的测试原理,并结合具体测试数据对测试的方法和仪器进行了分析.     

Fenton法降解垃圾渗滤液中的溶解性有机质

垃圾渗滤液是一种高浓度难降解废水,含有大量有毒物质和溶解性有机质（dissolved organic matter, DOM）,可生化性差。Fenton试剂（Fe2++H2O2）能产生活性极强的羟基自由基（·OH）,能快速氧化渗滤液中DOM和微量有机物质。本研究采用Fenton法处理垃圾渗滤液,结果表明,在优化的处理条件下,渗滤液COD和TOC去除率分别为65%和42%,其中混凝作用去除的COD和TOC分别为20%和21%。进一步通过紫外可见光谱扫描、SUVA254、E3/E4等指标评价,发现Fenton法可以有效降低渗滤液中的DOM含量,大分子有机物的含量明显减少,而分子量小的有机物含量相对增加,反应体系中溶解性有机物分子量随着反应的进行而降低,腐殖化程度降低。利用GC-MS定性出渗滤液原液中47种有机物,该类有机物在Fenton反应后上清液中未再检出,但5种物质（邻苯二甲酸二（2-乙基己）酯、植酮、角鲨烯、麥角甾烷醇和二氢胆固醇）在沉淀的铁泥中检出。研究发现不同pH值、H2O2和Fe2+浓度条件下,残留的COD与DOM、TOC和UV254存在显著的相关关系（R2> 0.9）。本研究结果为改进垃圾渗滤液处理工艺和探索DOM在Fenton过程中的降解行为提供科学依据。     

生物质型煤成型技术开发实验研究

通过原有成型方式的工业成型观察和模压成型实验，提出并验证了完全利用生物质纤维的交联作用实现成型的新机制。其于中高压下物料的不可再压缩性和单向挤压也会导致更高的成型压力的新认识，设计和研制成按新机制成型的型轮。经此改进的工业成型试验达到了比模压成型更好的效果：不用预实送料，且成型性能；成型压力降至120MPa以下，成型许可水分成倍提高，适合的生物质配比范围15％－60％；仅利用送料螺旋的预实功能，即可实现纯生物质型块的成型。     

The organic precursors affecting the formation of disinfection by-products with chlorine dioxide

The object of this research was to study the formation of disinfection by-products by using chlorine dioxide (ClO2) as a disinfectant reacting with different properties of organic substance in natural aquatic environment. The adsorbent resin (XAD-4, XAD-7) was used to divide the organic matters in raw water into three groups. The influence of the function groups on structure, reaction tendency, and formation of disinfection by-products generated by the reaction of these organic substances with chlorine dioxide was explored. The experimental results show that the three different organic groups formed using adsorbent resin were hydrophobic substance, hydrophilic acid, and non-acid hydrophilics in proportions of 43%, 41%, and 16%, respectively. Within the raw water in our study, the hydrophilic substance had a higher distribution proportion than that described in general articles and journals, which indicates that this water was contaminated with pollution from human beings. The exploration of the reactivity of the three different organic substances with chlorine dioxide shows that the unit consumption of disinfection agent per unit organic matters (represented by ClO2/DOC) is in the following sequence hydrophobic substance > hydrophilic substance > non-acid hydrophilics. It indicated that larger molecular organic precursors had larger consumption of disinfectant. We also discovered that after the reaction of the three different organic substances with chlorine dioxide, the largest amount of disinfection by-products were generated by the non-acid hydrophilics.     

Characteristics of organic precursors and their relationship with disinfection by-products

The molecular weight distribution and chemical composition of precursors and their relationship with disinfection by-products (DBPs) were investigated. Most of the organic matter responsible for the major DBP precursors in the Pan-Hsin water are small compounds with a molecular weight less than 1 kDa. The hydrophobic acids display the greatest ability to produce DBP. Therefore, effective removal of small molecules or hydrophobic acidic organics prior to disinfection process will significantly reduce the DBP concentration in the finished water. Although the coagulation process is effective in removing large organic precursors and the removal efficiencies of CHCl3 formation potential and organic carbon increase proportionally to the molecular weight of the precursors, the conventional treatment methods have limited efficiency in eliminating small precursors, which have high DBP formation potential.     

玉米浸泡液制备苏云金杆菌生物杀虫剂的影响因素研究

以玉米淀粉生产过程中的浸泡液为培养基,摇瓶发酵培养苏云金杆菌生物杀虫剂,通过一系列单因子试验,考察了不同培养条件(种子液的种龄、接种量、浸泡液的含固率、初始pH值、摇床转速、发酵温度及发酵时间)对苏云金杆菌在玉米浸泡液中的生长(菌数增长与芽孢形成)以及发酵液的生物毒效的影响.研究表明,在最佳摇瓶培养条件(种子液种龄10 h,接种量2%,浸泡液含固量3%,初始pH值7.0～7.5,摇床转速200 r/min,发酵温度30℃)下发酵48 h,活菌数和活芽孢数分别可达到7.9×108 CFU/mL和5.5×108 CFU/mL,毒力效价为698.0 IU/μL.本试验可为生物农药的工业化生产提供实用参数.     

Interactive analysis of waste recycling and energy recovery program in a small-scale incinerator

Conflicting goals affecting solid waste management are explored in this paper to find the best implementation of resource recovery with a small-scale waste-to-energy process. Recycling paper and plastic material often leaves a shortage of thermal energy to support incineration that forces operators to supplement the process with auxiliary fuels. Although there are considerable profits to be made from material recovery, the increase of fuel usage causes conflict given that it is cost prohibitive. A series of trials performed on a small-scale 1.5-t/day incineration plant with a cyclone heat recovery system found that material recycling can impede performance. Experimental results are expressed as empirical regression formulas with regard to combustion temperature, energy transfer, and heat recovery. Process optimization is possible if the waste moisture content remains <30%. To test the robustness of the optimization analysis, a series of sensitivity analyses clarify the extent of material recycling needed with regard to plastic, paper, and metal. The experiments also test whether the moisture in the waste would decrease when recycling paper because of its exceptional capacity to absorb moisture. Results show that recycling paper is strongly recommended when the moisture content is >20%, whereas plastic recycling is not necessary at that moisture condition. Notably, plastic recovery reduces the heat needed to vaporize the water content of the solid waste, thus it is recommended only when the moisture content is <10%. For above-normal incineration temperatures, plastic recycling is encouraged, because it removes excess energy. Metal is confirmed as an overall priority in material recycling regardless of the moisture content of the incoming waste.