Ground discarded tires remove naphthalene, toluene, and mercury from water

Ground discarded tires adsorb naphthalene, toluene, and mercury ions (Hg2+) from aqueous solutions. Their sorption properties and kinetics were determined by batch equilibration techniques at 20 degrees C. The isotherms were linear for naphthalene and toluene and their sorption coefficients were about 1340 and 255 (ml/g), respectively. Sorption of the organic compounds by the ground rubber particles was relatively fast (within 30 min). However, the mercury isotherms were non-linear, and its sorption was slow as compared to the sorption of the organics. The rubber particles had a strong affinity for Hg2+. These results show that ground discarded tires are effective in removing organic compounds and Hg2+ from wastewater and other contaminated environments. In addition it would be a useful, environmentally friendly use of discarded tires (one tire per year per capita is discarded in the United States).     

Microbial degradation of phthalic acid esters under anaerobic digestion of sludge

The microbial degradation by anaerobic sludge of three phthalates, priority pollutants, listed by both China National Environmental Monitoring Center and the U.S.EPA, namely, dimethyl (DMP), di-n-butyl (DBP) and di-n-octyl (DOP) phthalates was investigated. The experimental results indicated that the biodegradation rate and the biodegradability of three phthalates under anaerobic conditions appeared to be related to the length of the alkyl-side chains. More than 90% of DMP and DBP with the short alkyl-side chain phthalates can be degraded, whereas the DOP degradation appeared to be relatively slow under the same experimental conditions. The quantity of methane produced was measured and the results showed that both the ester groups and the phthalate ring were mineralized at a significant rate. The kinetics study demonstrated that the biodegradation of three phthalates conformed to the first-order model with respect to their concentrations.     

Heavy metals in urban soils of East St. Louis, IL. Part II: Leaching characteristics and modeling

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

Comparison of particulate mass, chemical species for urban, suburban and rural areas in central Taiwan, Taichung

Aerosol samples for PM2.5, PM(2.5-10) and TSP were collected from June to September 1998 and from February to March 1999 in central Taiwan. Ion chromatography was used to analyze the acidic anions: sulfate, nitrate and chloride in the Universal samples. The ratios of fine particle concentrations to coarse particle concentrations displayed that the fine particle concentrations are almost greater than that of coarse particle concentrations in Taichung area. The average concentrations of PM2.5, PM(2.5-10) and TSP in urban sites are higher than in suburban and rural sites at both daytime and night-time. Chloride dominated in the coarse mode in daytime and in fine mode in night-time. Nitrate can be found in both the coarse and fine modes. Sulfate dominated in fine mode in both daytime and night-time.     

The photocatalytic disinfection of urban waste waters

In this paper we present the results of the photocatalytic disinfection of urban waste water. Two microbial groups, total coliforms and Streptococcus faecalis, have been used as indexes to test disinfection efficiencies. Different experimental parameters have been checked, such as the effect of TiO2, solar or UV-lamp light and pH. Disinfection of water samples has been achieved employing both UV-lamp and solar light in agreement with data shown by other authors. The higher disinfection rates obtained employing an UV-lamp may be explained by the stronger incident light intensity. Nevertheless no consistent differences have been found between TiO2-photocatalysis and direct solar or UV-lamp light irradiation at natural sample pH (7.8). At pH 5 the presence of TiO2 increases the relative inactivation rate compared with the absence of the catalyst. After the photocatalytic bacterial inactivation, the later bacterial reappearance was checked for total coliforms at natural pH and pH 5, with and without TiO2. Two h after the photocatalytic treatment, CFU increment was almost nill. But 24 and 48 h later an important bacterial CFU increment was observed. This CFU increment is slower after irradiation with TiO2 at pH 5 in non-air-purged samples.     

Photooxidation mechanism of nitrogen-containing compounds at TiO2/H2O interfaces: an experimental and theoretical examination of hydrazine derivatives

The photocatalytic oxidation of oxalyldihydrazide, N,N'-bis(hydrazocarbonyl)hydrazide, N,N'-bis(ethoxycarbonyl)hydrazide, malonyldihydrazide, N-malonyl-bis[(N'-ethoxycarbonyl)hydrazide] was examined in aqueous TiO2 dispersions under UV illumination. The photomineralization of nitrogen and carbon atoms in the substrates into N2 gas, NH4+ (and/or NO3-) ions, and CO2 gas was determined by HPLC and GC analysis. The formation of carboxylic acid intermediates also occurred in the photooxidation process. The photocatalytic mechanism is discussed on the basis of the experimental results, and with molecular orbital (MO) simulation of frontier electron density and point charge. Substrate carbonyl groups readily adsorb on the TiO2 surface, and the bonds between carbonyl group carbon atoms and adjacent hydrazo group nitrogen atoms are cleaved predominantly in the initial photooxidation process. The hydrazo groups were photoconverted mainly into N2 gas (in mineralization yields above 70%) and partially to NH4 ions (below 10%). The formation of NO3- ions was scarcely recognized.     

The occurrence of trihalomethanes in the drinking water in Greece

This paper summarizes and completes an investigation into the occurrence of trihalomethanes (THMs) in public water supplies in Greece. The investigation was conducted in three cities of Greece, Athens, Mytilene and Chalkida, from 1993 to 1998. Samples were collected from three treatment plants of Athens (Galatsi Treatment Plant--GTP, Menidi Treatment Plant--MTP, Kiourka Treatment Plant--KTP) and from the distribution systems of Athens, Mytilene and Chalkida. The sources for these systems are lakes, boreholes and wells. The concentrations of THMs ranged from 5 to 106 microg/l, from 4 to 27 microg/l and from 5 to 96 microg/l, in the distribution systems of Athens, Mytilene, Chalkida, respectively. The wide ranges of concentrations in three cities should be attributed to the organics concentration of raw water. In all the cases the THMs concentrations were higher during the summer and fall than in spring and winter. In GTP and in the distribution system receives water by GTP, from April 1993 to January 1995, Mytilene and Chalkida, brominated THMs dominated and existed at the highest concentration levels, whereas chloroform was the least prevalent compound, while in all the other cases the opposite was observed. In all samples the concentrations were lower than the maximum level of 100 microg/l for total trihalomethanes (TTHMs) set by European Community (EC).     

Monitoring, modelling and environmental exposure assessment of industrial chemicals in the aquatic environment

Monitoring and laboratory data play integral roles alongside fate and exposure models in comprehensive risk assessments. The principle in the European Union Technical Guidance Documents for risk assessment is that measured data may take precedence over model results but only after they are judged to be of adequate reliability and to be representative of the particular environmental compartments to which they are applied. In practice, laboratory and field data are used to provide parameters for the models, while monitoring data are used to validate the models' predictions. Thus, comprehensive risk assessments require the integration of laboratory and monitoring data with the model predictions. However, this interplay is often overlooked. Discrepancies between the results of models and monitoring should be investigated in terms of the representativeness of both. Certainly, in the context of the EU risk assessment of existing chemicals, the specific requirements for monitoring data have not been adequately addressed. The resources required for environmental monitoring, both in terms of manpower and equipment, can be very significant. The design of monitoring programmes to optimise the use of resources and the use of models as a cost-effective alternative are increasing in importance. Generic considerations and criteria for the design of new monitoring programmes to generate representative quality data for the aquatic compartment are outlined and the criteria for the use of existing data are discussed. In particular, there is a need to improve the accessibility to data sets, to standardise the data sets, to promote communication and harmonisation of programmes and to incorporate the flexibility to change monitoring protocols to amend the chemicals under investigation in line with changing needs and priorities.     

Mutagenic nitrated benzo[a]pyrene derivatives in the reaction product of benzo[a]pyrene in NO2-air in the presence of O3 or under photoirradiation

In order to clarify the contribution of nitrated products to the direct-mutagenic activity of products of the reactions of benzo[a]pyrene in NO2-air under various conditions, heterogeneous reactions of BaP deposited on filter in the air containing 10 ppm of NO2 have been conducted in dark or under photoirradiation. The reaction products have been analyzed by gas chromatography and mutagenicity of the products fractionated by preparative HPLC was assayed for Salmonella typhimurium strains TA98 and YG1024 in the absence of S9 mix. 3,6-dinitrobenzo[a]pyrene and 1,3-dinitrobenzo[a]pyrene, which are strong direct-acting mutagens, largely contributed to the total direct-acting mutagenicity of the dark reaction products in NO2-air. On the other hand, both the dark reaction in the presence of O3 and the photoreaction in NO2-air resulted in the formation of much smaller amounts of nitrobenzo[a]pyrenes than that observed in the dark reaction in the absence of O3. These results show that the contribution of other direct-acting mutagens to the total direct-acting mutagenicity of the products in these reactions should be considered. Benzo[a]pyrene lactones were identified in a highly mutagenic fraction of the products of the dark reaction in the presence of O3 and photoreaction and a nitrobenzo[a]pyrene lactone was also identified in a highly mutagenic fraction of the dark reaction products in the presence of O3. Nitrated oxygenated benzo[a]pyrene derivatives such as nitrobenzo[a]pyrene lactone were considered to largely contribute to direct-acting mutagenicity of the products of the dark reaction in the presence of O3 and photoreaction.     

A life-cycle comparison of alternative automobile fuels

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C2H5OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C2H5OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results. We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable, and reduce the demand for imported fuels. Fuels from food sources, such as biodiesel from soybeans and C2H5OH from corn, can be attractive only if the co-products are in high demand and if the fuel production does not diminish the food supply. C2H5OH from herbaceous or woody biomass could replace the gasoline burned in the light-duty fleet while supplying electricity as a co-product. While it costs more than gasoline, bioethanol would be attractive if the price of gasoline doubled, if significant reductions in GHG emissions were required, or if fuel economy regulations for gasoline vehicles were tightened.