Water washing effects on metals emission reduction during municipal solid waste incinerator (MSWI) fly ash melting process

This study investigated that water washing effects on the metals emission reduction in melting of municipal solid waste incinerator (MSWI) fly ash. Experimental conditions were conducted at liquid-to-solid (L/S) ratio 10, 20, and 100 for water-washing process and its subsequent melting treatment at 1450 °C for 2 h. The simple water-washing process as a pre-treatment for MSWI fly ash can remove most of the chlorides, leachable salts, and amphoteric heavy metals from the MSWI fly ash, resulting in the washed ash having lowered chlorine content. MSWI fly ashes washed by L/S ratio 10 and above that were melted at 1450 °C produced slag containing relatively high vitrificaton ratio of Cu and Pb. Besides, the vitrification ratios of Na, K, Ca, and Mg in washed MSWI fly ash were also higher than that of MSWI fly ash. The results indicated that washed MSWI fly ash can reduce the emission of metallic chlorides during its subsequent melting treatment.     

Characteristics of bricks made from waste steel slag

The characteristics of bricks made from steel slag were investigated in this research. Slag addition was shown to reduce the required firing temperature. When the firing temperature was greater than 1050 degrees C and the slag addition less than 10%, the bricks met ROC national standard CNS 3319 third-class brick for builders. The percentage of slag increased as the quartz and kaolin decreased in the sintered samples while the magnesium aluminum silicate and calcium silicate increased. There were no new crystal phases observed in these samples.     

Particulate matter emissions from on-road vehicles in a freeway tunnel study

Particulate matter, including coarse particles (PM_2.5–10, aerodynamic diameter of particle between 2.5 and 10 μm) and fine particles (PM_2.5, aerodynamic diameter of particle lower than 2.5 μm) and their compositions, including elemental carbon, organic carbon, and 11 water-soluble ionic species, and elements, were measured in a tunnel study. A comparison of the six-hour average of light-duty vehicle (LDV) flow of the two sampling periods showed that the peak hours over the weekend were higher than those on weekdays. However, the flow of heavy-duty vehicles (HDVs) on the weekdays was significant higher than that during the weekend in this study. EC and OC content were 49% for PM_2.5–10 and 47% for PM_2.5 in the tunnel center. EC content was higher than OC content in PM_2.5–10, but EC was about 2.3 times OC for PM_2.5. Sulfate, nitrate, ammonium were the main species for PM_2.5–10 and PM_2.5. The element contents of Na, Al, Ca, Fe and K were over 0.8 μg m^?3 in PM_2.5–10 and PM_2.5. In addition, the concentrations of S, Ba, Pb, and Zn were higher than 0.1 μg m^?3 for PM_2.5–10 and PM_2.5. The emission factors of PM_2.5–10 and PM_2.5 were 18 ± 6.5 and 39 ± 11 mg km^?1-vehicle, respectively. The emission factors of EC/OC were 3.6/2.7 mg km^?1-vehicle for PM_2.5–10 and 15/4.7 mg km^?1-vehicle for PM_2.5 Furthermore, the emission factors of water-soluble ions were 0.028(Mg²⁺)–0.81(SO₄^2?) and 0.027(NO₂^?)–0.97(SO₄^2?) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively. Elemental emission factors were 0.003(V)–1.6(Fe) and 0.001(Cd)–1.05(Na) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively.     

Adsorption characteristics of benzene on biosolid adsorbent and commercial activated carbons

This study selected biosolids from a petrochemical waste-water treatment plant as the raw material. The sludge was immersed in 0.5-5 M of zinc chloride (ZnCl2) solutions and pyrolyzed at different temperatures and times. Results indicated that the 1-M ZnCl2-immersed biosolids pyrolyzed at 500 degrees C for 30 min could be reused and were optimal biosolid adsorbents for benzene adsorption. Pore volume distribution analysis indicated that the mesopore contributed more than the macropore and micropore in the biosolid adsorbent. The benzene adsorption capacity of the biosolid adsorbent was 65 and 55% of the G206 (granular-activated carbon) and BPL (coal-based activated carbon; Calgon, Carbon Corp.) activated carbons, respectively. Data from the adsorption and desorption cycles indicated that the benzene adsorption capacity of the biosolid adsorbent was insignificantly reduced compared with the first-run capacity of the adsorbent; therefore, the biosolid adsorbent could be reused as a commercial adsorbent, although its production cost is high.     

Kinetics of benzene adsorption onto activated carbon

An activated carbon bed adsorption process is influenced by the adsorbents' characteristics, volatile organic compound (VOC) characteristics, and process conditions. In the literatures, the adsorption processes of the adsorbents and VOCs were usually considered to be in equilibrium. In this study, the VOC adsorption processes by activated carbon were considered to be a kinetic process, i.e. they are not in equilibrium. Then, isothermal adsorption curves and a small column experiment were simulated.     

Characteristics of organic precursors and their relationship with disinfection by-products

The molecular weight distribution and chemical composition of precursors and their relationship with disinfection by-products (DBPs) were investigated. Most of the organic matter responsible for the major DBP precursors in the Pan-Hsin water are small compounds with a molecular weight less than 1 kDa. The hydrophobic acids display the greatest ability to produce DBP. Therefore, effective removal of small molecules or hydrophobic acidic organics prior to disinfection process will significantly reduce the DBP concentration in the finished water. Although the coagulation process is effective in removing large organic precursors and the removal efficiencies of CHCl3 formation potential and organic carbon increase proportionally to the molecular weight of the precursors, the conventional treatment methods have limited efficiency in eliminating small precursors, which have high DBP formation potential.     

Decomposition of 2-mercaptothiazoline in aqueous solution by ozonation

This study investigates the ozonation of 2-mercaptothiazoline (2-MT). The 2-MT is one of the important organic additives for the electroplating solution of the printed wiring board industry and has been widely used as a corrosion inhibitor in many industrial processes. It is of concern for the aquatic pollution control especially in the wastewaters. Semibatch ozonation experiments in the completely stirred tank reactor are performed under various concentrations of input ozone. The concentrations of 2-MT, sulfate, and ammonium are analyzed at specified time intervals to elucidate the decomposition of 2-MT during the ozonation. In addition, the time variation of the dissolved ozone concentration (C(ALb)) is continuously monitored in the course of experiments. Total organic carbon (TOC) is chosen and measured as a mineralization index of the ozonation of 2-MT. The results indicate that the decomposition of 2-MT is efficient, while the mineralization of TOC is limited via the ozonation only. Simultaneously, the yield of sulfate with the maximum value of about 47% is characterized by the increases of TOC removal and ozone consumption. These results can provide some useful information for assessing the feasibility of the treatment of 2-MT in the aqueous solution by the ozonation.     

Characterizing In Situ Methane‐Enhanced Biostimulation Potential for 1,4‐Dioxane Biodegradation in Groundwater

This study characterizes the 1,4‐dioxane biodegradation potential for an in situ methane‐enhanced biostimulation field pilot study conducted at Air Force Plant 44, located south of the Tucson International Airport in Arizona. In this study, the use of methane as the primary substrate in aerobic cometabolic biodegradation of 1,4‐dioxane is evaluated using environmental molecular diagnostic tools. The findings are compared to an adjacent pilot study, wherein methane was generated via enhanced reductive dechlorination and where methane monooxygenase and methane‐oxidizing bacteria were also found to be abundant. This article also presents the use of ¹³C and ²H isotopic ratio enrichment, a more recent tool, to support the understanding of 1,4‐dioxane biodegradation in situ. This study is the first of its kind, although alkane gas‐enhanced biodegradation of 1,4‐dioxane has been evaluated extensively in microcosm studies and propane‐enhanced biodegradation of 1,4‐dioxane has been previously studied in the field. ©2016 Wiley Periodicals, Inc.     

A critical exploration of blood and environmental chromium concentration among oral cancer patients in an oral cancer prevalent area of Taiwan

The growing incidence of oral cancer (OC) in Taiwan has become a crucial public health concern. In particular, Changhua, a county in central Taiwan, carries persistently high OC incidence rate, with an alarmingly high male/female ratio of OC incidence. Previous epidemiological studies had found that the incidence is spatially correlated with the level of soil content to certain heavy metals in the central Taiwan area. Soil and the human body both intake environmental heavy metals, which can be absorbed through various ways. The soil metal concentration is an index of possible environmental exposure to heavy metal, and the blood metal concentration somewhat reflects the level of the exposure on the human body. Metallic carcinogen is likely to generate free radicals and play a role in many cancers, and many studies had reported that environmental exposure to heavy metals is an important risk factor for developing cancer. Studies on animals showed that chronic intake of chromium (Cr) could induce OC. This study aims to explore the association between the Cr concentration in the farm soil and in the blood of OC patients. We recruited 79 OC patients from Changhua County, with their lifestyle being adjusted in regression analysis. The results showed that the Cr concentration in the blood of OC patients is significantly higher than the background value, and is positively associated with the Cr concentration in the soil surrounding their residence (p-value < 0.023). Because Changhua County is only with moderate prevalence of the known OC habitual risk factors, an environmental factor related to heavy metal Cr exposure is suspected. Future investigations may verify the causal relation between Cr and OC.     

Monolignol biosynthesis and genetic engineering of lignin in trees, a review

This paper summarizes our previous and current research on genetic engineering of lignin biosynthesis for the purposes of improving wood pulping and bleaching efficiency. For these purposes, our targets were to produce transgenic trees with low content of lignin that is also chemically reactive (high lignin S/G ratio). Using aspen as a model species, we have characterized the biochemical functions of various genes and the kinetic properties of these gene products involved in monolignol biosynthetic pathway. The results of these characterizations proved strong evidence for a principle phenolic flux leading to the formation of monolignols. Biochemical evidence further demonstrated that, in this principle flux, 4CL could be the enzyme limiting total lignin accumulation, whereas CAld5H might control the lignin S/G ratio. These propositions were fully supported by the in vivo functions of these enzymes. Transgenic trees with inhibited 4CL enzyme activity exhibited 5–45% reduction in lignin contents. The chemical structure of the resulting lignin remained essentially unchanged. More importantly, the lignin reduction was compensated for by a concomitant increase in cellulose content. When antisense 4CL and sense coniferaldehyde 5-hydroxylase (CAld5H) genes were simultaneously transferred into aspen via Agrobacterium, transgenic trees expressing each one and both of the transgenes were produced. Lignin reductions up to 55% were achieved in antisense 4CL plants and up to 3-fold S/G increases were observed in sense CAld5H plants. These effects were independent but additive, with plants expressing both transgenes having less lignin and higher S/G ratio. Consistent with our previous results, lignin reduction has always resulted in an increase in cellulose content. These transgenics could be potentially valuable for pulp production. But more importantly, these benchmark transgenics are rich sources of information for functional genomics and metabolic engineering, allowing the generation of the ultimate raw materials for wood pulp production.