炼铝作业氟化物接触剂量与发病关系的分析

目的 了解炼铝作业氟的危害状况,为工业性氟病的防治提供依据.方法 对氟作业环境作职业卫生学调查.采用剂量患病率寿命表法对866名电解铝作业工人工业性氟病的发病情况进行流行病学调查,并作相关回归分析.结果 该厂接氟工人工业性氟病的总患病率为1.73%,且患病率随累积接氟量的增加而升高,呈高度正相关(r＝0.997,P＜0.01).并据所求得回归方程(y＝10.34InD-18.21)推算出接氟工人控制患病率时的允许连续工作年限和今后的发病趋势.结论 该厂电解铝车间氟危害较重,应加强卫生防护措施,并建议将车间氟最高容许浓度从目前1 mg/m3降为0.5 mg/m3为宜.     

长江干支流输沙量减少趋势及其影响因素浅析

通过对长江干支流各主要水文控制站的多年径流量、输沙量、含沙量、中值粒径等水沙基本特征值的统计分析，表明在过去的近50年时间内，长江干支流的年径流量中心趋势不存在具有显著统计意义的变化，而输沙量、含沙量、中值粒径值均有明显的下降态势。以水库建设和水土保持为主的人类活动是长江干支流泥沙输移量减少趋势的重要影响因素，在20世纪90年代以前长江输沙量的减少主要是水库建设的影响，之后随着“长治”工程的展开则兼具了水库建设和水土保持的影响，未来水土保持工作对长江保水减沙的长期效益将更为显著。     

低施磷水平下不同施肥对太湖地区黄泥土磷迁移性的影响

对太湖地区水稻土上长达13年的长期不同施肥处理的某试验田进行了土壤全磷、树脂磷和水溶性磷的测定分析.不同处理的年施磷量为0～53kg/(hm²·a),土壤全磷为0.3～0.5g·k^-1.根据土壤磷素的质量平衡,计算表明该水稻土存在的磷素流失量为2～8kg/(hm²·a),单施化肥下的流失量最大,为配施有机肥处理的2～4倍;水溶性磷的比率在0.2%～0.4%间,且不同施肥实践对其的影响不明显.但单施化肥有使亚表层树脂磷和水溶性磷含量提高的倾向.长期施用化肥配施大量鲜猪粪使树脂磷含量提高20～40 mg·kg^-1,但与长期施用化肥配施秸秆的处理一样没有发生在有机质增加下的磷活化而提高磷流失.这些说明本地区长期单施化肥的水稻土中可能存在强烈的磷流失,且水稻土磷流失并不以水溶解发生.为了防止水稻土磷的强烈水流失而加剧农业非点源污染,要避免长期单施化肥,而应坚持和推广配施适量有机肥.     

衍生化气相色谱法测定黄磷诱发氧化水中苯酚降解产物

利用衍生化气相色谱法对黄磷诱发氧化苯酚降解产物进行了研究，在磷酸存在下，以甲醇作酯类衍行生试剂，分别和ＳＥ－５２和ＨＰ－１７石英毛细管双柱结合ＧＣ－ＭＳ进行分离定性定量，黄磷诱发氧化苯酚降解产物以羧酸为主，在反应温度５０℃时，表现为一级反应特征，速率常数（Ｋ）：０．０７７ｍｉｎ＾－１，半衰期（ｔ１／２）：９．０ｍｉｎ。     

Recharge signal identification based on groundwater level observations

This study applied a method of the rotated empirical orthogonal functions to directly decompose the space-time groundwater level variations and determine the potential recharge zones by investigating the correlation between the identified groundwater signals and the observed local rainfall records. The approach is used to analyze the spatiotemporal process of piezometric heads estimated by Bayesian maximum entropy method from monthly observations of 45 wells in 1999-2007 located in the Pingtung Plain of Taiwan. From the results, the primary potential recharge area is located at the proximal fan areas where the recharge process accounts for 88% of the spatiotemporal variations of piezometric heads in the study area. The decomposition of groundwater levels associated with rainfall can provide information on the recharge process since rainfall is an important contributor to groundwater recharge in semi-arid regions. Correlation analysis shows that the identified recharge closely associates with the temporal variation of the local precipitation with a delay of 1-2 months in the study area.     

Magnetotactic bacteria: Characteristics and environmental applications

• Magnetotactic bacteria (MTB) synthesize magnetic nanoparticle within magnetosomes. • The morphologic and phylogenetic diversity of MTB were summarized. • Isolation and mass cultivation of MTB deserve extensive research for applications. • MTB can remove heavy metals, radionuclides, and organic pollutants from wastewater. Magnetotactic bacteria (MTB) are a group of Gram-negative prokaryotes that respond to the geomagnetic field. This unique property is attributed to the intracellular magnetosomes, which contains membrane-bound nanocrystals of magnetic iron minerals. This review summarizes the most recent advances in MTB, magnetosomes, and their potential applications especially the environmental pollutant control or remediation. The morphologic and phylogenetic diversity of MTB were first introduced, followed by a critical review of isolation and cultivation methods. Past research has devoted to optimize the factors, such as oxygen, carbon source, nitrogen source, nutrient broth, iron source, and mineral elements for the growth of MTB. Besides the applications of MTB in modern biological and medical fields, little attention was made on the environmental applications of MTB for wastewater treatment, which has been summarized in this review. For example, applications of MTB as adsorbents have resulted in a novel magnetic separation technology for removal of heavy metals or organic pollutants in wastewater. In addition, we summarized the current advance on pathogen removal and detection of endocrine disruptor which can inspire new insights toward sustainable engineering and practices. Finally, the new perspectives and possible directions for future studies are recommended, such as isolation of MTB, genetic modification of MTB for mass production and new environmental applications. The ultimate objective of this review is to promote the applications of MTB and magnetosomes in the environmental fields.     

Cu/Cr co-stabilization mechanisms in a simulated Al2O3-Fe2O3-Cr2O3-CuO waste system

• Cu and Cr can be mostly incorporated into CuFe_xAl_yCr_2−x−yO₄ with a spinel structure. • Spinel phase is the most crucial structure for Cu and Cr co-stabilization. • Compared to Al, Fe and Cr are easier to be incorporated into the spinel structure. • ‘Waste-to-resource’ by thermal process at attainable temperatures can be achieved. Chromium slag usually contains various heavy metals, making its safe treatment difficult. Glass-ceramic sintering has been applied to resolve this issue and emerged as an effective method for metal immobilization by incorporating heavy metals into stable crystal structures. Currently, there is limited knowledge about the reaction pathways adopted by multiple heavy metals and the co-stabilization functions of the crystal structure. To study the Cu/Cr co-stabilization mechanisms during thermal treatment, a simulated system was prepared using a mixture with a molar ratio of Al₂O₃:Fe₂O₃:Cr₂O₃:CuO= 1:1:1:3. The samples were sintered at temperatures 600–1300°C followed by intensive analysis of phase constitutions and microstructure development. A spinel phase (CuFe_xAl_yCr_2−x−yO₄) started to generate at 700°C and the incorporation of Cu/Cr into the spinel largely complete at 900°C, although the spinel peak intensity continued increasing slightly at temperatures above 900°C. Fe₂O₃/Cr₂O₃ was more easily incorporated into the spinel at lower temperatures, while more Al₂O₃ was gradually incorporated into the spinel at higher temperatures. Additionally, sintered sample microstructures became more condensed and smoother with increased sintering temperature. Cu / Cr leachability substantially decreased after Cu/Cr incorporation into the spinel phase at elevated temperatures. At 600°C, the leached ratios for Cu and Cr were 6.28% and 0.65%, respectively. When sintering temperature was increased to 1300°C, the leached ratios for all metal components in the system were below 0.2%. This study proposes a sustainable method for managing Cu/Cr co-exist slag at reasonable temperatures.     

崇明岛公路两侧蔬菜地土壤和蔬菜重金属污染研究

为了研究崇明岛公路两侧土壤和蔬菜重金属污染状况,采集陈海、北沿公路两侧蔬菜地土壤、蔬菜和路面灰尘样品,测定重金属Pb、Cd、Cu、Zn含量.结果表明,以上海市土壤环境背景值上限值为评价标准,所有土壤样品Pb、Cd、Cu和Zn的超标率分别为10.1%、25.4%、6.5%和8.7%;以HJ 332-2006 食用农产品产地环境质量评价标准中蔬菜地土壤环境质量评价指标限值(pH值6.5～7.5)为标准,Cd超标率在21.0%,仅有不到3%样品Pb含量超标,而没有样品Cu、Zn含量超标.以国家食品卫生标准中规定的重金属限量为标准,路侧蔬菜样品Pb含量超标率为43.2%,Cd为18.6%,Zn和Cu则小于5%.由此可见,崇明岛主要公路两侧土壤污染以Cd为主,而蔬菜污染则以Pb为主.在长期运营的前提下,低交通量公路两侧50 m范围内耕作层土壤和两侧作物会发生一定程度的重金属污染,路面灰尘是路侧土壤和蔬菜的潜在污染源.     

等离子体协同光催化去除模拟烟气中SO2的实验研究

近年来,低温等离子体技术以及纳米TiO₂光催化技术在烟气脱硫中的应用越来越引起人们的关注。利用填充床反应器将这2种技术有机地结合起来，进行了大量脱硫实验研究。研究结果表明，等离子体协同光催化去除烟气中的SO₂与单独采用等离子体技术相比，其SO₂的去除率可提高5%～20%。同时，探讨了等离子体协同TiO₂光催化剂的脱硫机理，分别研究了外加电压、气体流量和SO₂初始浓度等因素对脱硫效率的影响。实验结果表明，当SO₂初始浓度为800 mg/m³，输入电压为17.5 kV，气体流量为0.2 m³/h时，SO₂脱除率可以达到77.6%。     

Cooling suits, physiological response, and task performance in hot environments for the power industry.

Heat stress on workers working outdoors in the power industry may result in fatigue and deterioration in task performance. This research collected and analyzed data on task performance of workers working indoors and outdoors with and without a cooling suit. The task performance was compared on the basis of heart rate, oxygen consumption, tympanic temperature, subjective responses, productivity, and error rates. Based on One-Way Analysis Of Variance (ANOVA) results, a significantly lower estimated working oxygen consumption was observed (p < .001) when the cooling suit was worn. The productivity was higher while workers wore the cooling suit as compared to no cooling suit (p = .011) whereas the error rates were significantly lower (p < .001). Also a significantly lower self-reported discomfort was observed in the neck and shoulders while working wearing the cooling suit (p = .004). This study concluded that wearing a cooling suit while working outdoors was associated with physiological benefits as well as improved task performance of the study participants.