Survey of the occurrence of residues of methyl tertiary butyl ether (MTBE) in Dutch drinking water sources and drinking water

An indicative survey has been carried out in The Netherlands investigating the presence of methyl tertiary butyl ether (MTBE) in drinking water and the corresponding sources. In total, 71 different sites used for the preparation of drinking water in The Netherlands were sampled in two successive seasons in 2001 involving the analysis of 156 samples. (ground water (n = 88), surface water (n = 17), bank filtrate water (n = 6) and drinking water (n = 45)). To combine high sample throughput with high selectivity and sensitivity, off-line purge and trap for sampling and gas chromatography mass spectrometry equipped with an automated thermal desorption sampler (TDS-GC-MS) was selected as the preferred analytical methodology. The developed procedure enabled the analysis of at least 40 samples per day and provided a limit of quantification of 2 ng l(-1). In the first period 63 samples of raw water were analyzed. Concentrations ranged between < 10 ng l(-1) and 420 ng l(-1) with a median concentration below 10 ng l(-1). The second period was focused at the re-sampling of positive locations (MTBE > 10 ng l(-1)) and a few additional drinking water utilities of which both the raw and drinking water of the utilities were analyzed. The median concentration of MTBE in the selected set of drinking water samples was 20 ng l(-1) (n = 45). At one location MTBE was found at a level of 2900 ng l(-1) caused by point source contamination of the ground water (11 900 ng l(-1)). Special attention has been paid to the quality of the results by analyzing all samples in duplicate and the analysis of control samples during each series of analyses.     

Environmental monitoring of historical change in arsenic deposition with tree bark pockets

ICP-MS analysis recorded historical change (c. 1846 to 2002) in the arsenic concentration of bark included within the trunks (tree bark pockets) of two Japanese oak trees (Quercus crispula), collected at an elevated location approximately 10 km from the Ashio copper mine and smelter, Japan. The arsenic concentration of the bark pockets was 0.016 +/- 0.003 microg cm(-2) c. 1846 (n = 5) and rose 50-fold from c. 1875 to c. 1925, from approximately 0.01 to 0.5 microg cm(-2). The rise coincided with increased copper production in Ashio from local sulfide ores, from 46 tons per year in 1877 to 16,500 tons per year in 1929. Following a decline in arsenic concentration and copper production, in particular during the Second World War, a second peak was observed c. 1970, corresponding to high levels of production from both local (6,000 tons per year) and imported (30,000 tons per year) ores, smelted from 1954. Compared to the local ores, the contribution of arsenic from imported ores appeared relatively low. Arsenic concentrations declined from c. 1970 to the present following the closure of the mine in 1974 and smelter in 1989, recording 0.058 +/- 0.040 microg cm(-2) arsenic (n = 5) in surface bark collected in 2002. The coincident trends in arsenic concentration and copper production indicated that the bark pockets provided an effective record of historical change in atmospheric arsenic deposition.     

The application of HPLC-F and GC-MS to the analysis of selected hydroxy polycyclic hydrocarbons in two certified fish bile reference materials

Four selected hydroxy polycyclic aromatic hydrocarbons (OH-PAHs), 2-hydroxy-naphthalene (2-OH-NPH), 1-hydroxy-phenanthrene (1-OH-PHE), 1-hydroxy-pyrene (1-OH-PYR) and 3-hydroxy-benzo[a]pyrene (3-OH-BaP) have been analysed in two certified fish bile reference materials (CRMs) for exposure monitoring of PAHs in the aquatic environment. The two materials, BCR 720 and BCR 721, consist of bile from fish exposed to contaminated sediment and dispersed crude oil, respectively. Both bile samples have been analysed by two different analytical techniques, gas chromatography-mass spectrometry (GC-MS) and high performance liquid chromatography-fluorescence detection (HPLC-F), and the separation performance, detection limits, recoveries and reproducibility for the four target compounds were evaluated. HPLC-F requires a simple sample preparation and the separation capacity is adequate for quantification of 1-OH-PYR and 3-OH-BaP. Detection limits are excellent for 1-OH-PYR (6 pg injected) and 3-OH-BaP (3 pg injected) and generally improved with increasing molecular size. Recoveries ranged from 48 to 99% for the four selected compounds, depending on compound and concentration. Sample preparation prior to GC-MS analysis was more demanding, as reflected by the obtained recoveries for 2-OH-NPH, 1-OH-PHE and 1-OH-PYR (35 to 61%). The sensitivity improved with decreasing molecular size, 2-OH-NPH (1.2 pg injected), 1-OH-PHE (2.4 pg injected) and 1-OH-PYR (6 pg injected). Because of the superior separation power of GC and the extra selectivity of MS detection, GC-MS was the method of choice for the determination of 2-OH-NPH and 1-OH-PHE in both CRMs. In fish bile samples these two compounds are more likely to suffer from chromatographic overlap, and HPLC-F was not sufficiently selective. Determination of 1-OH-PYR was performed with success by both methods, but HPLC-F would be preferred because of the simpler and less time-consuming sample preparation. Detectable concentrations of 3-OH-BaP were present in BCR 720 and could only be determined by HPLC-F. The present work aims to present HPLC-F and GC-MS as complementary methods for the quantitative analysis of OH-PAHs in fish bile.     

Matrix diffusion effects in the cleanup of heterogeneous aquifers

Simple mathematical models are developed to account for the rather slow mass transport of nonaqueous phase liquid (NAPL) into aqueous solution in groundwater during flushing operations. The models are based on the assumption that this bottleneck in the process is associated with diffusion in the aqueous phase in the porous medium from the location of the NAPL drops/ganglia in a region of relatively low permeability out into a region of substantially higher permeability, somewhat analogous to diffusion from a block of porous rock into a nearby fracture, where the fracture system overwhelmingly dominates the overall permeability. The models include batch flushing, flushing in a laboratory column, and a one-dimensional model for flushing by means of a single recovery well.     

Assessing land use impacts on flood processes in complex terrain by using GIS and modeling approach

A distributed hydrologic modeling and GIS approach is applied for the assessment of land use impact in the Steinsel sub-basin, Alzette, Grand-Duchy of Luxembourg. The assessment focuses on the runoff contributions from different land use classes and the potential impact of land use changes on runoff generation. The results show that the direct runoff from urban areas is dominant for a flood event compared with runoff from other land use areas in this catchment, and tends to increase for small floods and for the dry season floods, whereas the interflow from forested, pasture and agricultural field areas contributes to the recession flow. Significant variations in flood volume, peak discharge, time to the peak, etc., are found from the model simulation based on the three hypothetical land use change scenarios.     

Optimizing the removal of small fish passage barriers

Removing small artificial barriers that hinder upstream migrations of fish is a major problem in riparian habitat restoration. Because of budgetary limitations, it is necessary to prioritize barrier removal and repair decisions. These have usually been based on scoring and ranking procedures, which, although simple to use, can be very inefficient in terms of increasing the amount of accessible instream habitat. We develop a novel decision-making approach, based on integer programming techniques, which optimizes repair and removal decisions. Results show based on real datasets of barrier culverts located in Washington State that scoring and ranking is over 25% below the optimum on average and a full 100% below in the worst case, producing no net habitat gain whatsoever. This is compared to a dynamic programming method that was able to find optimal solutions in less than a second, even for problems with up to several hundred variables, and a heuristic method, which found solutions with less than a 1% average optimality gap in even less time.     

Application of a checklist for quality assistance in environmental modelling to an energy model

Large, complex energy models present considerable challenges to develop and test. Uncertainty assessments of such models provide only partial guidance on the quality of the results. We have developed a model quality assistance checklist to aid in this purpose. The model checklist provides diagnostic output in the form of a set of pitfalls for the model application. The checklist is applied here to an energy model for the problem of assessing energy use and greenhouse gas emissions. Use of the checklist suggests that results on this issue are contingent on a number of assumptions that are highly value-laden. When these assumptions are held fixed, the model is deemed capable of producing moderately robust results of relevance to climate policy over the longer term. Checklist responses also indicate that a number of details critical to policy choices or outcomes on this issue are not captured in the model, and model results should therefore be supplemented with alternative analyses.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).