Henry’s law constant measurements for formaldehyde and benzaldehyde as a function of temperature and water composition

Henry’s law constants H of formaldehyde and benzaldehyde were determined using a dynamic system based on the water/air equilibrium at the interface within the length of a microporous tube. The measurements were conducted over the range 273–293 K in (i) deionized water, (ii) 35 g L^?1 solution of NaCl simulating seawater and (iii) two nitric acid solutions, i.e. 0.63 and 6.3 wt%.In pure water, the obtained data were used to derive the following Arrhenius expressions: ln H = (6423 ± 542)/T ? (13.4 ± 2.0) and ln H = (6258 ± 280)/T ? (17.5 ± 1.0) for formaldehyde and benzaldehyde, respectively. The H values, calculated at 293 K from Arrhenius expressions cited above were the following (in units of M atm^?1): H = 5020 ± 1170 (formaldehyde), H = 47 ± 5 (benzaldehyde). The temperature dependence of H permits then to derive the solvation enthalpies for both compounds: ΔH_solv = ?(53.4 ± 4.5) kJ mol^?1 and ΔH_solv = ?(52.0 ± 2.3) kJ mol^?1 for formaldehyde and benzaldehyde, respectively.In 35 g L^?1 salt solution, the H values were 27–66% and 12–21% lower than their respective determinations in deionized water, for formaldehyde and benzaldehyde respectively. The observed salt effect was used to estimate the following Setschenow coefficients at 293 K for 0.6 M NaCl: formaldehyde (0.21) and benzaldehyde (0.09).In 6.3 wt% nitric acid solution, H values of benzaldehyde were approximately 30% higher than those found in pure water although no significant influence was observed for formaldehyde.Finally, our experimental data were then used to estimate the fractions of formaldehyde and benzaldehyde in atmospheric aqueous phase and their derived atmospheric lifetimes.     

Preparation and Properties of Carboxymethyl Cellulose (CMC)/Sodium alginate (SA) Blends Induced by Gamma Irradiation

Carboxymethyl Cellulose (CMC)/Sodium alginate (SA) blends have been prepared by casting solution method. The effect of different irradiation doses (2.5, 5, 10, 15, and 20 kGy) of gamma rays on the physical properties of the CMC/SA blend containing different ratios of SA (20, 30, and 40 %) such as gel fraction (%) and swelling (%) of CMC/SA blends were investigated. It was found that the gel fraction increases with increasing irradiation dose up to 20 kGy while the swelling of CMC/SA blend films tends to increase with increasing SA content and reduced with increasing irradiation doses. Mechanical and thermal properties of the blend films were improved when CMC content increased and with increasing irradiation dose up to 20 kGy. Morphology of the blend was examined by SEM, which indicates compatibility between CMC and SA. The blend rich in SA content possessed good antimicrobial activity against Gram +ve Bacteria (Bacillus subtilis).     

Effect of dimethoate on the immune system of female mice

Abstract

The functional status of the immune system of female mice exposed to a single oral dose of dimethoate (16 mg / kg) was evaluated by assessing cell mediated and humoral immune responses, in addition to the effect of dimethoate on spleen and body weights after different time intervals. The data showed that dimethoate caused a time ‐ depended decrease in spleen weights in the absence of a change in body weights. The immunologic effect of dimethoate to female mice produced a dose‐dependent decrease in the number of the rosette forming cells (total and active erythrocyte rosette). The ability of splenocytes to proliferation in response to mitogens; phytohemagglutinin (PHA) for T cell and lipopolysaccharide (LPS) for B cell were significantly decreased at the different times. As compared to control, a significant decrease in serum total immunoglobulins (Ig) and IgM was found, while IgG was non‐significant deceased. Results of this study also revealed that dimethoate caused a significant decrease in the number of plaque forming cell (PFC / 10⁶ splenocytes) in a time dependent manner.     

APCA Honors Five Individuals and Three Sections In 1988 Awards Program

The aim of this study was to analyze the incidence of fungi in the chapel crypt. The MAS 100 was used to monitor the air pollution. The lowest numbers of fungal colonies were isolated at the entrance to the cemetery (2400 CFU/m3). The outside temperature ranged from 24.5oC to 28.1oC, and relative humidity was between 35.3% and 46.4 %. The highest of fungal colonies from air samples at baseline were isolated inside the crypt when coffin was opened (4820 CFU/m3). The temperature in the crypt at baseline varied between 19.6°C and 25.6°C and humidity was between 50.8% and 60.1%. The number of fungal colonies increased significantly at the end of the study. Ten species of fungi were isolated from air samples inside and outside the chapel, and seven species of fungi were isolated on the surface of the exterior and interior of the chapel. Thirteen types/species of fungus were isolated from air samples collected in the crypt; 15 species of fungi were isolated on the walls, surface of the coffin, bones and other objects. Assessment of fungi in the air samples and different surfaces of the crypt, it revealed very high levels of molds in the air samples.

Implications: Assessment of fungi in the air samples and different surfaces of the crypt revealed high levels of molds in the air samples. Fungal numbers within the crypt exceed recommended limits for occupational exposure. Employees working in the crypts should know about these hazards.     

Chemical and biological release of 14C‐bound residues from soil treated with 14C‐p,p'‐DDT

Abstract

¹⁴C‐p,p'‐DDT‐bound residues in soil can be released by treatment with concentrated sulphuric acid at ambient temperatures. Within 6 days, about 70% of the bound residues was released. Bound residues released after 9 months incubation with ¹⁴C‐DDT showed the presence of DDT and DDE only while bound residues released after 18 months, contained in addition 13% DDD.

Release of bound ¹⁴C‐residues also occurs readily following inoculation of the soil‐bound residues with fresh soil or with individual microorganisms. Almost complete release of bound residues was observed after incubation for 45 days. The rate of release was rapid during the first two weeks and decreased thereafter. TLC and HPLC analysis showed that the released residues contained DDE (about 80%) and a smaller amount of DDD. The disappearance of DDT from the released residues may be attributed to its microbiological degradation to DDE and DDD, shortly after its release.     

Applying physicochemical approaches to control phosphogypsum heavy metal releases in aquatic environment

One of the most important sources of solid waste in the Mediterranean Basin ecosystem originated from the phosphate fertilizer industries, which discharge phosphogypsum (PG) directly into aquatic environments or are stacked on stockpiles. The present study investigates metal release from PG under the influence of variable pH, increasing PG mass content, and complexing organic matter ligands. Major ions from PG leachates, grain size and charge, main functional groups along with metal leachability (Pb, Cd, Cr, Cu, and Zn) were determined using ion chromatography, laser diffraction, zetameter, Fourier transform infrared spectroscopy, and atomic absorption spectroscopy, respectively. The complete dissolution of PG recorded is at 2 g/L. Saturation and supersaturation with respect to PG may occur at concentrations of 3 and 4 g/L, respectively, revealing a clustering phenomenon leading to heavy metal encapsulation within the aggregates. Organic ligands such as citrate may trigger the cationic exchange within the PG suspension leading to ion release. As these factors are considered as specific process involving the release of contaminants from PG during storage under natural conditions, this study could set the foundations for PG remediation in aquatic environment. Organic ligands under controlled pH conditions could be utilized in treating fertilizer industrial wastes by taking into consideration the particularity of the receiving area, thus decreasing metal hazardous impact on natural media.     

Decision making under uncertainty using PEES–fuzzy AHP–fuzzy TOPSIS methodology for landfill location selection

The location selection for landfill municipal solid waste is an important issue in waste management. Selection of the optimal location requires consideration of multiple alternative solutions and evaluation factors because of system complexity. Further, ranking of the alternative locations and selection of the most optimal and efficient locations for landfill waste are an important multi-criteria decision-making problem. In this study, the candidate locations for landfill are determined based on Political, Economical, Environmental and Social factors are assessed through decision-makers’ opinion and by the methodology that incorporates fuzzy analytic hierarchy process (fuzzy AHP) and fuzzy technique for order preference by similarity to ideal solution (fuzzy TOPSIS). Specifically, the fuzzy AHP technique is applied to determine the weights of selected criteria impacting the location selection process, and the fuzzy AHP is adapted to model the linguistic vagueness and ambiguity, which can also be expressed as triangular fuzzy numbers. Furthermore, fuzzy TOPSIS technique is employed to rank the alternative locations. The applicability of this methodology is demonstrated by a case study of landfill waste location selection in the region of Casablanca, Morocco, and the results are compared with other techniques. Finally, to complete the treatment, a sensitivity analysis is performed to examine the impact of the preferences given by decision-makers to choose the best location.     

Cobalt separation from waste mobile phone batteries using selective precipitation and chelating resin

Separation of cobalt from mixed-waste mobile phone batteries containing LiCoO₂ cathodic active material was investigated using selective precipitation and chelating resin. Cobalt was recovered from the active powder materials containing 47 % Co oxide together with Mn, Cu, Li, Al, Fe, and Ni oxides. The metal ions were leached sufficiently using 4 M HCl. The metal ions detected spectrophotometrically were removed from the leaching solution by selective precipitation at pH 5.5, with cobalt loss of 27.5 %. Conditions for achieving a recovery of Co in the filtrate by chelating resin were determined experimentally by varying the pH and time of the reaction, as well as the initial resin-to-liquid ratio. The cobalt was efficiently determined by absorption spectrometry at λ _max 510 nm. Chelating polyamidoxime resin was synthesized by polymerization of acrylonitrile and followed by amidoximation reaction. Physically cross-linked gel of polyacrylonitrile was made by a cooling technique.     

Brown rust disease control in winter wheat: I. Exploring an approach for disease progression based on night weather conditions

An empirical approach for simulating the infection and progress of leaf rust (caused by Puccinia triticina) during stem elongation on winter wheat was analysed for the 2000 to 2006 growing seasons. The approach was elaborated based on night weather conditions (i.e., air temperature, relative humidity and rainfall) and leaf rust occurrences. Data from three consecutive cropping seasons (2000–2002) at four representative sites of the Grand-Duchy of Luxembourg were used in the set-up phase. The capability to correctly simulate the occurrence expression of P. triticina infections on the upper leaf layers was then assessed over the 2003–2006 period. Our study revealed that the development of leaf rust required a period of at least 12 consecutive hours with air temperatures ranging between 8 and 16 °C, a relative humidity greater than 60 % (optimal values being 12–16 °C and up to 80 % for air temperatures and relative humidity, respectively) and rainfall less than 1 mm. Moreover, leaf rust occurrences and infections were satisfactorily simulated. The false alarm ratio was ranged from 0.06 to 0.20 in all the study sites. The probability of detection and critical success index for WLR infection were also close to 1 (perfect score).     

Investigation of novel material for effective photodegradation of bezafibrate in aqueous samples

A novel composite with an enhanced photocatalytic activity was prepared and applied to study the removal of bezafibrate (BZF), a hypolypemic pharmaceutical, from an aqueous environment. For the enhancement of titanium dioxide photoactivity a fullerene derivative, 2-(ferrocenyl) fulleropyrrolidine (FcC₆₀), was synthesized and applied. Obtained composite was found to show a higher catalytic activity than pristine TiO₂. Therefore, high hopes are set in composites that are based on carbonaceous nanomaterials and TiO₂ as a new efficient photocatalysts.