固相微萃取分析条件的优化

主要介绍了固相微萃取作为一种样品前处理技术,如何对影响其分配系数的各因素,如：萃取头的选择、萃取方式、萃取温度等进行优化选择,从而提高方法灵敏度及回收率。     

Stabilization of heavy metals in MSWI fly ash using silica fume

The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR (²⁷Al and ²⁹Si) techniques. It was found that silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.     

游离氨对热水解联合中温厌氧消化处理剩余污泥的影响

热水解预处理强化了污泥厌氧消化过程,但同时增加了微生物受游离氨抑制的风险.对比传统工艺,在有机容积负荷率1.74~4.27gVS/(L·d)条件下,研究了游离氨(FA)对热水解联合中温厌氧消化工艺性能的影响.结果表明,组合工艺甲烷产量较传统反应器提高89%~121%,有机去除率提高1.21~1.46倍.但同时导致系统中游离氨浓度达89~382mgN/L,显著高于传统工艺中37~84mgN/L的范围.游离氨毒性测试显示,传统工艺中FA浓度从43mgN/L升至84mgN/L,没有抑制解乙酸产甲烷途径,而组合工艺中FA升至264mgN/L时,表现出抑制作用,尽管厌氧菌对高浓度FA表现更强的驯化趋势.结合氮负荷试验, FA浓度与基质利用能力,解乙酸产甲烷途径抑制程度和挥发性有机酸积累的关系表明,高有机负荷条件下组合工艺效率可通过控制氮负荷优化.     

铜管模拟输配系统中氯胺衰减过程与模拟

研究了氯胺在铜管模拟输配系统中的衰减过程,并利用一级反应动力学模型对氯胺衰减规律进行了模拟;考察了pH、初始氯胺浓度等水质条件与流速等水力条件对氯胺衰减速率的影响.结果表明,pH值是影响氯胺衰减速率与金属铜溶出的重要因素,pH越低氯胺衰减越快;提高氯胺初始浓度可加快氯胺衰减速度,也可增加金属铜的溶出量;流速对氯胺衰减速率的影响不大.此外,衰减动力学过程模拟结果表明,采用一级反应动力学模型可以较好地拟合不同条件下的氯胺衰减规律.从而对于工程中不同条件下消毒剂浓度预测具有重要意义.     

Preparation of biochar catalyst with saccharide and lignocellulose residues of corncob degradation for corncob hydrolysis into furfural

This paper presented a novel process for production of furfural by hydrothermal degradation of corncob over biochar catalyst, in which it was prepared with the recycling degradation solution and lignocellulosic solid residues. The biochar catalyst was papered by lignocellulose residues and concentrated saccharide solution, and then impregnated in 0.5 mol/L sulphuric acid at room temperature for 24 h assisted by the ultrasonic vibration. In the system of recycling, 8.8 % lignocellulose residues and 100 % concentrated saccharide solution from corncob hydrolysis have been recycled. Hydrolysis of corncob was carried out at 180 °C for duration of 170 min over the biochar catalyst. The experimental results have shown that the furfural yield of up to 37.75 % and overall corncob conversion rate of 62.00 % could be achieved under optimum operating conditions for the catalysts preparation and the corncob hydrolysis. It is believed that the acid density of 4.27 mmol/g of biochar catalyst makes the SO₃H groups cleave β-1,4 glycosidic linkages effectively and hydrolyze the cellulose and hemicellulose to water-soluble sugars, as well as to facilitate dehydration of xylose to give the product of furfural.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

Life cycle assessment of biodiesel fuel production from waste cooking oil in Okayama City

A life cycle assessment (LCA) is performed to make clear of the actual environment impacts from conversation of waste cooking oil (WCO) to biodiesel fuel (BDF) in Okayama. A scenario analysis is carried out based on different participation rate of residents who separate WCO from general waste, corresponding to different BDF utilisation rate in transportation system. Sub scenarios complying with different gas emission standards regarding vehicles are designed as well. Afterwards, life cycle impact assessment is conducted to focus on global warming, acidification, and urban air pollution. Overall improvement of almost all kinds of life cycle inventories is significant when diesel is replaced with BDF, demonstrating that a shift from WCO-to-incineration to WCO-to-BDF is more beneficial. Under carbon neutral, compared to base scenario (S0), about 746.05 ton CO₂ emission will be reduced annually in the scenario with 100 % BDF utilisation in vehicles (S4). Meanwhile, total external cost in three environmental impacts (EI) sharply reduces by 51.90 %, showing much economic sustainability in S4. Moreover, the manufacturing cost for producing one litter WCO-to-BDF is 97.32 Yen. Sensitivity analysis shows that the gas emission standard regarding vehicles had much bigger effect on EI than BDF manufacturing process in this research.     

High CO2 adsorption on improved ZSM-5 zeolite porous structure modified with ethylenediamine and desorption characteristics with microwave

Journal of Material Cycles and Waste Management - Synthesized zeolite Socony Mobil-5 (ZSM-5) with large pore surface structures and modified with ethylenediamine were used to achieve high CO2...     

Monitoring and Assessment of Persistent Organochlorine Residues in Sediments from the Daliaohe River Watershed, Northeast of China

Surface sediment samples from 12 sites of the three selected rivers in Daliaohe River watershed (Hunhe River, Taizihe River and Daliaohe River) were analyzed with the objective of establishing sources and hazard of the organochlorinae pesticides (OCPs) and polychlorinated biphenyl (PCBs) in surface sediments. The total concentrations of OCPs varied from 3.06 to 23.24 ng g⁻¹. ∑HCH (α-HCH, β-HCH, δ-HCH, γ-HCH), ∑DDT (p, p′-DDE, p, p′-DDD, o, p′-DDT, p, p′-DDT) and ∑Cyclodiene (Heptachlor, Aldrin, Heptachlor epoxide, Dieldrin, Endrin) ranged from 1.86 to 21.48, 0.5 to 2.81 and 0.56 to 1.53 ng g⁻¹, respectively. Results of OCPs also illustrate that the most dominant pollutants among the OCPs was ∑HCH, and γ-HCH was the most dominant isomer in HCH, which was evidence of recent input of lindane. It possibly came from the runoff of polluted soils and long-scale transportation. Total PCB concentrations ranged between 1.88 and 16.88 ng g⁻¹. The peak concentrations of PCBs were found in sediments from station T5 and D3, which are in the vicinity of industrial areas and ferry, respectively. These data show a moderate level of OCPs and PCBs contaminations compared to that in other countries.     

Canopy Spectra and Remote Sensing of Ashe Juniper and Associated Vegetation

A study was conducted in central Texas to determine the potential of using remote sensing technology to distinguish Ashe juniper (Juniperus ashei Buchholz) infestations on rangelands. Plant canopy reflectance measurements showed that Ashe juniper had lower near-infrared reflectance than other associated woody plant species and lower visible reflectance than mixed herbaceous species in spring and summer. Ashe juniper could be distinguished on color-infrared aerial photographs acquired in March, April, June, and August and on QuickBird false color satellite imagery obtained in June, where it had a distinct dark reddish-brown tonal response. Unsupervised classification techniques were used to classify aerial photographic and satellite imagery of study sites. An accuracy assessment performed on a computer classified map of a photographic image showed that Ashe juniper had producer's and user's accuracies of 100% and 92.9%, respectively, whereas an accuracy assessment performed on a classified map of a satellite image of the same site showed that Ashe juniper had producer's and user's accuracies of 94.1% and 88.1%, respectively. Accuracy assessments performed on classified maps of satellite images of two additional study sites showed that Ashe juniper had producer's and user's accuracies that ranged from 87.1% to 96.4%. These results indicate that both color-infrared photography and false color satellite imagery can be used successfully for distinguishing Ashe juniper infestations.