Volatile nanoparticle formation and growth within a diluting diesel car exhaust

A major source of particle number emissions is road traffic. However, scientific knowledge concerning secondary particle formation and growth of ultrafine particles within vehicle exhaust plumes is still very limited. Volatile nanoparticle formation and subsequent growth conditions were analyzed here to gain a better understanding of "real-world" dilution conditions. Coupled computational fluid dynamics and aerosol microphysics models together with measured size distributions within the exhaust plume of a diesel car were used. The impact of soot particles on nucleation, acting as a condensational sink, and the possible role of low-volatile organic components in growth were assessed. A prescribed reduction of soot particle emissions by 2 orders of magnitude (to capture the effect of a diesel particle filter) resulted in concentrations of nucleation-mode particles within the exhaust plume that were approximately 1 order of magnitude larger. Simulations for simplified sulfuric acid-water vapor gas-oil containing nucleation-mode particles show that the largest particle growth is located in a recirculation zone in the wake of the car. Growth of particles within the vehicle exhaust plume up to detectable size depends crucially on the relationship between the mass rate of gaseous precursor emissions and rapid dilution. Chassis dynamometer measurements indicate that emissions of possible hydrocarbon precursors are significantly enhanced under high engine load conditions and high engine speed. On the basis of results obtained for a diesel passenger car, the contributions from light diesel vehicles to the observed abundance of measured nucleation-mode particles near busy roads might be attributable to the impact of two different time scales: (1) a short one within the plume, marked by sufficient precursor emissions and rapid dilution; and (2) a second and comparatively long time scale resulting from the mix of different precursor sources and the impact of atmospheric chemistry.     

博茨瓦纳欧科范果湿地1972～2000年泛滥方式

欧科范果三角洲地区泛滥范围年年在变化.这种变化与安哥拉高地集水区的区域性降水及当地降雨量有关.我们采用了1972～2000年的3000多幅卫星图像来描绘湿地的格局,其中从1985～2000年的图像几乎是NOAAAVHRR每日连续传送的,1972年以来的其它图像是从Landsat传感器上传下来的,其连续性次之.对AVHRR图像每10天为一期,用无监督分类方法分成陆地和水体.对LandsatTM和ERS2-ATSR数据进行分析的结果,与测算的淹没区域89%相吻合.结果显示欧科范果湿地近期30年期间的变化约在2450～11400km2之间.     

Detoxification of ferrocyanide in asoil–plant system

The detoxification of iron cyanide in a soil–plant system was investigated to assess the total cyanide extracted from contaminated soil and allocated in the leaf tissue of willow trees(Salix caprea). They were grown in soil containing up to 1000 mg/kg dry weight(dw) of cyanide(CN),added as ~(15)N-labeled potassium ferrocyanide and prepared with a new method for synthesis of labeled iron cyanides. CN content and ~(15)N enrichment were monitored weekly over the exposure in leaf tissue of different age. The ~(15)N enrichment in the young and old leaf tissue reached up to 15.197‰ and 9063‰, respectively; it increased significantly over the exposure and with increasing exposure concentrations(p 0.05). Although the CN accumulation in the old leaf tissue was higher, compared to the young leaf tissue(p 0.05), the ~(15)N enrichment in the two tissue types did not differ statistically. This indicates a non-uniform CN accumulation but a uniform ~(15)N allocation throughout the leaf mass. Significant differences were detected between the measured CN content and the C~(15)N content, calculated from the ~(15)N enrichment(p 0.05), revealing a significant CN fraction within the leaf tissue, which could not be detected as ionic CN. The application of labeled iron CN clearly shows that CN is detoxified during uptake by the willows. However, these results do not exclude other detoxification pathways, not related to the trees. Still, they are strongly indicative of the central role the trees played in CN removal and detoxification under the experimental conditions.     

Effect of C/N ratio, aeration rate and moisture content on ammonia and greenhouse gas emission during the composting

Gaseous emission (N₂O, CH₄ and NH₃) from composting can be an important source of anthropogenic greenhouse gas and air pollution. A laboratory scale orthogonal experiment was conducted to estimate the effects of C/N ratio, aeration rate and initial moisture content on gaseous emission during the composting of pig faeces from Chinese Ganqinfen system. The results showed that about 23.9% to 45.6% of total organic carbon (TOC) was lost in the form of CO₂ and 0.8% to 7.5% of TOC emitted as CH₄. Most of the nitrogen was lost in the form of NH₃, which account for 9.6% to 32.4% of initial nitrogen. N₂O was also an important way of nitrogen losses and 1.5% to 7.3% of initial total nitrogen was lost as it. Statistic analysis showed that the aeration rate is the most important factor which could affect the NH₃ (p = 0.0189), CH₄ (p = 0.0113) and N₂O (p = 0.0493) emissions significantly. Higher aeration rates reduce the CH₄ emission but increase the NH₃ and N₂O losses. C/N ratio could affect the NH₃ (p = 0.0442) and CH₄ (p = 0.0246) emissions significantly, but not the N₂O. Lower C/N ratio caused higher NH₃ and CH₄ emissions. The initial moisture content can not influence the gaseous emission significantly. Most treatments were matured after 37 days, except a trial with high moisture content and a low C/N ratio.     

Acoustic underwater signals with a probable function during competitive feeding in a tadpole

Acoustic communication is widespread among adult stages of terrestrial animals and fish and has also been observed in insect larvae. We report underwater acoustic communication in the larvae of a frog, Gephyromantis azzurrae, from Isalo, a sandstone massif in western Madagascar. According to our field data, these tadpoles live in streams and prefer habitats characterized by comparatively low temperatures, shallow water depth, and a relatively fast current. Feeding experiments indicated that the tadpoles are carnivorous and macrophagous. They consumed insect larvae and, to a lesser extent, small shrimps, and conspecific as well as heterospecific tadpoles. Calls of these tadpoles consisted either of single click notes or of irregular series of various clicks. Some complex calls have a pulsed structure with three to nine indistinct energy pulses. Production of the pulses coincided with rapid closure of the jaw sheaths and often with an upward movement of the body. Calls were emitted while attacking prey and occurred significantly more often when attacking conspecifics. Tadpoles that had not been fed for some time emitted sounds more frequently than those that had been regularly fed. The spectral frequency of the calls differed in tadpole groups of different size and was higher in groups of smaller tadpoles, suggesting that spectral frequency carries some information about tadpole size which might be important during competitive feeding to assess size and strength of competitors. This report differs from those for the larvae of South American horned frogs, Ceratophrys ornata. These are the only other tadpoles for which sound production has reliably been reported but the calls of Ceratophrys tadpoles occur mainly in a defensive context.     

Geometric variability and surface finish of weld zones in Yb:YAG laser welded advanced high strength steels

Laser welding is used for joining advanced high strength steels (AHSS) to improve formability and performance. In this paper, the geometric variability observed in the fusion zones and heat affected zones of several combinations of AHSS (different types, coatings and thicknesses), which were butt welded using a Trumpf TRUDISK 6000^® Yb:YAG laser beam, is presented. The surface texture parameters such as roughness and waviness of laser welds were also measured and correlated with geometric variability. Results indicate that although high quality welds with minimal defects can be obtained using the Yb:YAG laser welding process, there is considerable variation in both the shape and the dimensions of weld zones. The variability increased with an increase in thickness differentials between the sheets being welded. Analysis of the top of the weld surfaces also suggested that aluminum coating on USIBOR samples contributes significantly to increased roughness. An increase in laser power coupled with corresponding increase in welding speed did not impact variability. A fair correlation between the surface roughness and weld region variability exists, although this needs further study.