Comprehensive temperature monitoring in an in-vessel forced-aeration static-bed composting process

Comprehensive temperature monitoring was done in an in-vessel forced-aeration static-bed composting process using sewage sludge. The three layers that divided the compost pile horizontally showed different temperature distributions. The temperature of the top layer appeared not to be influenced by the ambient temperature. The temperature of the center area of the top layer was taken to be the representative temperature for evaluating composting start-up performance. The temperature of the bottom layer was strongly influenced by the ambient temperature, and the temperature of the center area of the bottom layer was taken to be the representative temperature for pathogen control as it was the minimum temperature in the reactor. Composting start-up performance was influenced by several factors when the ambient temperature was either below or above 20°C. When the ambient temperature was below 20°C, the time taken to reach 65°C (T ₆₅) was influenced by the temperature of inflowing air, but when the temperature was higher than 20°C, it was influenced by the ratio of sewage sludge to seed compost (F/S). T ₆₅ was least when F/S was 1–2. Received: January 9, 2001 / Accepted: October 10, 2001     

Determination of photosynthetic pigment composition in an individual phytoplankton cell in seas and lakes using fluorescence microscopy; properties of the fluorescence emitted from picophytoplankton cells

To develop a method for the determination of photosynthetic pigment species in individual phytoplankton cells, especially natural picophytoplankton cells, the fluorescence spectra of intact cells were studied with cultured phytoplankton. The study was made mainly with phycoerythrin-containing picophytoplankton collected off Japan in 1982 with reference to diatomal species and phycoerythrin-free cyanophycean species. The spectra were measured for cell suspensions with an ordinary spectrofluorometer, and for individual cells with a microscope spectrofluorometer, paying special attention to the effect of cell-fixation. Results indicated that: (1) the cell-fixation with the glutaraldehyde and paraformaldehyde mixture modified phycoerythrin emission from picophytoplankton markedly in its wavelength location and intensity, but (2) the emission from phycocyanin was affected far less, and (3) the emission from chlorophyll a was not altered. However, the phycoerythrin emission modified by the fixation was found to be easily distinguished from other emissions, and kept its intensity high enough for detection with a fluorescence microscope. The fluorescence properties after the fixation were kept unaltered for a long period of time. Based on the results, we propose a simple method for the determination of photosynthetic pigments in individual phytoplankton cells in seas and lakes using fluorescence microscopy. Results of our tests with natural samples of phytoplankton are presented, and problems for further improvement are also discussed.     

Environmental-economic models for total emission control of regional environmental pollution — input-output approach

This paper deals with a Leontief-type dynamic input-output analysis for total emission control of pollution. A dynamic input-output model can be described as a linear programming problem. In this paper an objective function to be minimized is chosen as the sum of pollutants emitted in a regional area throughout the planning period. It is assumed that consumption grows with a constant growth rate throughout the planning period. With this model, we can tell how to assign the elimination rate of pollutants to each production sector, under the constraint that the total emission standard is satisfied in each term of the planning period.     

Simplified Fabrication of Optically Transparent Composites Reinforced with Nanostructured Chitin

Optically transparent films reinforced with micro to nano scale chitin particles were successfully developed in this study. Chitin composites based on micro scale particles which are larger than the optical wavelength do not cause light scattering provided that chitin particles are composed of nano structure networks which allow monomer impregnation and polymerization. This could lead a simplified process for fabricating transparent composites. The composites reinforced by the chitin micro particles not only retained the transparency of the plastic but also helped the effectiveness of its co-efficient of thermal expansion as similar to chitin nanofibers. Furthermore, chitin nanofibers transparent films are thermally stable against temperature as high as 200 °C for a long period of time. This could lead to number of important commercial applications, and is a significant move towards the sustainable utilization of marine bio-resources.     

Molding Method, Thermal and Mechanical Properties of Jute/PLA Injection Molding

Natural composites have been important materials system due to preservation of earth environments. Natural fibers such as jute, hemp, bagasse and so on are very good candidate of natural composites as reinforcements. On the other hand regarding matrix parts thermosetting polymer and thermoplastic polymer deriver form petrochemical products are not environmental friendly material, even if thermoplastic polymer can be recycled. In order to create fully environmental friendly material (FEFM) biodegradable polymer which can be deriver from natural resources is needed. Therefore poly(lactic acid) (PLA) polymer is very good material for the FEFM. In this paper jute fiber filled PLA resin (jute/PLA) composites was fabricated by injection moldings and mechanical properties were measured. It is believable that industries will have much attention to FEFM, so that injection molding was adopted to fabricate the composites. Long fiber pellet fabricated by pultrusion technique was adopted to prepare jute/PLA pellet. Because it is able to fabricate composite pellets with relative long length fibers for injection molding process, where, jute yarns were continuously pulled and coated with PLA resin. Here two kinds of PLA materials were used including the one with mold releasing agent and the other without it. After pass through a heated die whereby PLA resin impregnates into the jute yarns and sufficient cooling, the impregnated jute yarns were cut into pellets. Then jute/PLA pellets were fed into injection machine to make dumbbell shape specimens. In current study, the effects of temperature of PLA melting temperature i.e. impregnation temperature and the kinds of PLA were focused to get optimum molding condition. The volume fractions of jute fiber in pellet were measured by several measuring method including image analyzing, density measurement and dissolution methods. Additionally, thermal and mechanical properties were investigated. It is found that 250° is much suitable for jute/PLA long fiber pultrusion process because of its less heat degradation of jute, better impregnation, acceptable mechanical property and higher production efficiency. Additionally the jute fibers seem much effective to increase deflection temperature under load, tensile modulus and Izod strength.     

日本城市土壤的重金属污染研究

采用X-射线光谱法测定了一些日本城市公园土壤样品中的Pb,Zn,Cu,Cr,Ni,As,Fe,Ti,Mn,K,Ca,Rb和Sr共13种元素,结果发现Pb和Zn的含量在土壤剖面中从上至下有明显下降的趋势,并显示出Pb与Zn污染有一定的相关关系。同时,也探讨了一种判断土壤污染的方法。      

Troop size,habitat quality,and home range area in Japanese macaques

Summary The correlation between troop size (N) and home range area (R) is examined in terms of habitat quality with 32 data sets for the Japanese macaque (Macaca fuscata) from its entire distribution range. The habitat quality is represented by the vegetation type and the degree the habitat is disturbed. A proportional relationship is found between N and R when the two major vegetation types (deciduous and evergreen) are discriminated and only the data from relatively undisturbed habitats are considered. This result is discussed in relation to bioenergetics.     

Two-phase flow insights into open-channel flows with suspended particles of different densities

The effect of particle density on the turbulent open-channel flow carrying dilute particle suspensions is investigated using two specific gravities and three concentrations of solid particles. The particles, identical in size and similar in shape, were natural sand and a neutrally buoyant plastic. The particles were fully suspended, and formed no particle streaks on the channel’s bed. Accordingly, the changes in the flow are attributed to the interactions between suspended particles and flow turbulence structures. Measurements were obtained by means of image velocimetry enabling simultaneous, but distinct, measurement of liquid and particle velocities. The experimental results show that, irrespective of particle specific gravity, particle suspension influences bulk velocity of flow and the Kármán coefficient, while friction velocity essentially remains constant. The results also show that particles in suspension modify local water turbulence over the flow depth, but in ways not accurately predicted using the customary parameters for characterizing turbulence modification.     

Estrus cycle asynchrony in wild female chimpanzees, Pan troglodytes schweinfurthii

Although estrous synchrony has been reported in a number of mammalian species, most often among primates, methodological and analytical problems make it difficult to interpret these results. We developed a novel estrous synchrony index and employed a randomization procedure to analyze long-term observations of female chimpanzee (Pan troglodytes schweinfurthii) estrous cycles at the Mahale Mountains National Park, Tanzania. Our results revealed that female chimpanzees at Mahale avoid synchronizing their estrous periods with each other. We also found that birthrates decreased as the breeding sex ratio increased. We suggest that estrous asynchrony decreases female–female competition for mates. Asynchrony may also reduce the potential for male sexual coercion by nonpreferred mating partners.