Optimization of photo-Fenton process parameters on carbofuran degradation using central composite design

Carbofuran, one of the most toxic and biorefractory carbamate compounds, is widely used in insecticides in Taiwan (9-18% of total insecticides production per year). In the present study, a central composite design experiment was used to study the effect of photo-Fenton treatment on carbofuran solution and to optimize the process variables such as carbofuran concentration (1-100 mg L(-1)), H(2)O(2) dosage rate (0.25-6 mg L(-1) min(-1)) and Fe(3+) dosage (1-50 mg L(-1)), which influenced the efficiency of carbofuran degradation and mineralization. The results indicated that all the variables investigated in this study had significant roles in the degradation and mineralization of carbofuran in solution. The carbofuran degradation and mineralization efficiencies were increased with increase in H(2)O(2) dosage rate and Fe(3+) dosage, and with decrease in carbofuran concentration. Furthermore, optimum values of both H(2)O(2) dosage rate and Fe(3+) dosage were found to shift to higher values as carbofuran concentration increased. Based on the model obtained in this study, optimum H(2)O(2) dosage rate and Fe(3+) dosage were found to be 4 mg L(-1) min(-1) and 20 mg L(-1), respectively, for 51 mg L(-1) of carbofuran concentration. Under these conditions, carbofuran was completely removed within 30 min and coupled with 78% mineralization at the end of experiment.     

Effect of diurnal changes in VOC source strengths on performances of receptor models

Introduction

The effect of diurnal changes in strengths of volatile organic compound (VOC) sources on the performances of positive matrix factorization (PMF) and principal component analysis (PCA) was investigated using ambient measurement results that were taken during daytime and nighttime hours between March 24 and May 14, 2011, within Davutpasa Campus of Yildiz Technical University (Istanbul, Turkey).

Methods

Forty-five VOC species, ranging from C₅ to C₁₁ in volatility, were measured in the samples, 40 of which are included in the analyses. Ambient samples were grouped as daytime, nighttime, and all day datasets, and both PMF and PCA were applied to each dataset. A total of six source groups were extracted from each dataset: solvent use, general industrial paint use, gasoline and diesel vehicle exhausts, and biogenic as well as evaporative emissions. Estimated source contributions showed great diurnal variations.

Results

The results suggested that extraction of possible sources by PCA depends greatly on the number of samples and the strength of the sources, while PMF produced stable results regardless of number of samples and source strengths.

Conclusion

Although PMF was unable to resolve gasoline vehicle and evaporative emissions, it was found to be successful in explaining diurnal fluctuations in source strengths, while the performance of PCA depends on the strength of emission source.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Meta-analysis of environmental contamination by alkylphenols

Alkylphenols and alkylphenol ethoxylates (APE) are toxics classified as endocrine-disrupting compounds; they are used in detergents, paints, herbicides, pesticides, emulsifiers, wetting and dispersing agents, antistatic agents, demulsifiers, and solubilizers. Many studies have reported the occurrence of alkylphenols in different environmental matrices, though none of these studies have yet to establish a comprehensive overview of such compounds in the water cycle within an urban environment. This review summarizes APE concentrations for all environmental media throughout the water cycle, from the atmosphere to receiving waters. Once the occurrence of compounds has been assessed for each environmental compartment (urban wastewater, wastewater treatment plants [WWTP], atmosphere, and the natural environment), data are examined in order to understand the fate of APE in the environment and establish their geographical and historical trends. From this database, it is clear that the environment in Europe is much more contaminated by APE compared to North America and developing countries, although these APE levels have been decreasing in the last decade. APE concentrations in the WWTP effluent of developed countries have decreased by a factor of 100 over the past 30?years. This study is aimed at identifying both the correlations existing between environmental compartments and the processes that influence the fate and transport of these contaminants in the environment. In industrial countries, the concentrations observed in waterways now represent the background level of contamination, which provides evidence of a past diffuse pollution in these countries, whereas sediment analyses conducted in developing countries show an increase in APE content over the last several years. Finally, similar trends have been observed in samples drawn from Europe and North America.     

Particulate matter emission rates from beef cattle feedlots in Kansas-reverse dispersion modeling

Open beef cattle feedlots emit various air pollutants, including particulate matter (PM) with equivalent aerodynamic diameter of 10 microm or less (PM10); however limited research has quantified PM10 emission rates from feedlots. This research was conducted to determine emission rates of PM10 from large cattle feedlots in Kansas. Concentrations of PM10 at the downwind and upwind edges of two large cattle feedlots (KS1 and KS2) in Kansas were measured with tapered element oscillating microbalance (TEOM) PM10 monitors from January 2007 to December 2008. Weather conditions at the feedlots were also monitored. From measured PM10 concentrations and weather conditions, PM10 emission rates were determined using reverse modeling with the American Meteorological Society/U.S. Environmental Protection Agency Regulatory Model (AERMOD). The two feedlots differed significantly in median PM10 emission flux (1.60 g/m2-day for KS1 vs. 1.10 g/m2-day for KS2) but not in PM10 emission factor (27 kg/1000 head-day for KS1 and 30 kg/1000 head-day KS2). These emission factors were smaller than published U.S. Environmental Protection Agency (EPA) emission factor for cattle feedlots.     

Molecular characterization of denitrifying bacteria isolated from the anoxic reactor of a modified DEPHANOX plant performing enhanced biological phosphorus removal

Enhanced Biological Phosphorus Removal (EBPR) under anoxic conditions was achieved using a Biological Nutrient Removal (BNR) system based on a modification of the DEPHANOX configuration. Double-probe Fluorescence in Situ Hybridization (FISH) revealed that Polyphosphate Accumulating Organisms (PAOs) comprised 12.3 +/- 3.2% of the total bacterial population in the modified DEPHANOX plant. The growing bacterial population on blood agar and Casitone Glycerol Yeast Autolysate agar (CGYA) medium was 16.7 +/- 0.9 x 10(5) and 3.0 +/- 0.6 x 10(5) colony forming units (cfu) mL(-1) activated sludge, respectively. A total of 121 bacterial isolates were characterized according to their denitrification ability, with 26 bacterial strains being capable of reducing nitrate to gas. All denitrifying isolates were placed within the alpha-, beta-, and gamma-subdivisions of Proteobacteria and the family Flavobacteriaceae. Furthermore, a novel denitrifying bacterium within the genus Pseudomonas was identified. This is the first report on the isolation and molecular characterization of denitrifying bacteria from EBPR sludge using a DEPHANOX-type plant.     

Sisal/Carbon Fibre Reinforced Hybrid Composites: Tensile, Flexural and Chemical Resistance Properties

The variation of mechanical properties such as tensile and flexural properties of randomly oriented unsaturated polyester based sisal/carbon fibre reinforced hybrid composites with different fibre weight ratios have been studied. The chemical resistance test of these hybrid composites to various solvents, acids and alkalies were studied. The effect of NaOH treatment of sisal fibres on the tensile, flexural and chemical resistance properties of these sisal/carbon hybrid composites has also been studied. The hybrid composites showed an increase in tensile and flexural properties with increase in the carbon fibre loading. The tensile properties and flexural properties of these hybrid composites have been found to be higher than that of the matrix. Significant improvement in tensile properties and flexural properties of the sisal/carbon hybrid composites has been observed by alkali treatment. The chemical resistance test results showed that these untreated and alkali treated hybrid composites are résistance to all chemicals except carbon tetra chloride. Hand lay-up technique was used for making the composites and tests are carried out by using ASTM methods.     

The Efficacy of a Programme of Landslide Risk Reduction in Areas of Unplanned Housing in the Eastern Caribbean

Poor countries are disproportionately affected by the cost of disasters. Yet there is evidence of the benefits of seeking to mitigate the impact of a disaster, compared with the costs incurred in ‘making good’ after a major event has occurred. This article reviews a programme of landslide risk reduction in unplanned communities in the Eastern Caribbean. The construction of appropriate surface water management measures, based on the application of scientific and engineering principles, has been demonstrated to reduce the hazard from rainfall-triggered landslides. Adopting a community-based approach additionally delivers social and environmental benefits relating to employment generation, improvements in the environmental conditions within the community, and improvements slope management practices. The sustained implementation of the community-based projects has provided the necessary evidence-base for these practices to influence Government policy and practice, and gain recognition from regional development agencies. The strategic and incremental uptake of the community-based methodology is demonstrated to be an effective means for delivering physical landslide risk reduction measures in the most ‘at risk’ areas of unplanned housing.     

Lateral movement of soil fumigants 1,3-dichloropropene and chloropicrin from treated agricultural fields

The soil fumigants 1,3-dichloropropene (1,3-D) and chloropicrin (CP) are often used for controlling soil-borne plant pathogens and parasitic nematodes before reestablishing new vineyards and orchards. To evaluate crop safety and environmental risks with the replant fumigation, four field experiments were performed over 2 yr to examine 1,3-D and CP lateral movement away from the treated fields. Shank injection with or without a virtually impermeable film (V1F) was used in two vineyard fumigation experiments, and spot drip application without tarp cover was used in two orchard experiments. Results showed that 1,3-D and CP gases moved laterally to 6 m from the treated fields when the fumigants were applied by shank injection. The maximum 1,3-D or CP soil gas concentration at 6 m was approximately 10 ng cm(-3) when the fumigated plot was not cover with a tarp. With VIF, the measured maximum concentration increased to approximately 100 ng cm(-3). In the spot drip application, maximum 1,3-D and CP gas concentrations reached approximately 100 ng cm(-3) but at 1.5 m radial distance from the point of fumigant injection.