Economic Impact of Mass Production of Alternative Low Emission Automotive Power Systems

The study considers a range of possible effects on the transportation industry, satellite industries, the labor market, and the economy which may be anticipated in the event mass production of unconventional low emission automotive propulsion systems should occur, whether as a consequence of federal intervention, or not. A postulated 1 976 Otto Cycle Internal Combustion Engine equipped with a dual catalyst manifold reactor and other “conventional” emission control devices was compared in detail with a Regenerative Free Turbine Engine and a Rankine Cycle Engine, as specified by the contracting agency. Manufacturing costs, operating and ownership costs, consumer demand, inter-industry effects, employment, resource requirements, and international trade implications were analyzed in depth under a number of plausible sets of policy constraints and parametric variations. Principal conclusions are that conversion over a 10 year period is feasible, that manufacturing cost differentials are less critical than fuel consumption and cost differentials, that industry/employment impacts are minor, and that resource/trade effects are dominated by petroleum imports. Implications for federal policy are discussed.     

Automotive Exhaust Emission Levels by Geographic Area and Vehicle Make A Nationwide Survey

Gross average automotive exhaust emissions data collected by the Atlantic Richfield Clean Air Caravan during the summer of 1970 showed only slight geographical variations when the specific makes were ignored. When considering specific makes, significant differences were found on an average emissions basis. Vehicle population—emission distributions showed wide variations in the 50% population levels and in the percent of vehicles with emissions greater than specified values. Hydrocarbon (HC) and carbon monoxide (CO) data are given on a gross basis for the 1970, 1968-69, 1966-67, and pre-1966 model year group vehicles. Average HC and CO emissions and vehicle population-Idle emissions distribution curves are included for specific make vehicles in selected areas.     

Surface Air Pollutant Concentration Frequency Distributions: Implications for Urban Modeling

With the development of ambient air quality standards (AAQS), the need arises to describe the characteristics of regional surface air-pollutant concentration frequency distributions. In the evaluation of land use plans, numerous agencies will be concerned with evaluating the effectiveness of emission zoning and/or control actions. On a regional basis, one means of performing this assessment lies in determining the changes in the pollutant frequency distributions resulting from control actions.

This study presents new data concerning the surface air-pollutant concentration frequency distributions observed for area sources and continuous point sources, and compares these distributions with those of the pertinent meteorological variables describing the transport and diffusion of the pollutant. The observed surface air pollutant frequency distributions are compared to those corresponding to simple modeling concepts from either an urban area source or a continuous point source. For an urban source and a relatively inert pollutant like CO, we found that the observed frequency distribution for CO surface air concentration parallels the approximately log-normal frequency distribution of the reciprocal of the wind speed. We show that the constant relating these two well-correlated frequency distributions can be determined either experimentally or with a numerical simulation model of air pollution. The usefulness of numerical models in air pollution is discussed.     

Variance Design and Air Pollution Control

Confronted with shortages of low sulfur content residual fuel oil and, consequently, faced with the threat of social and economic upheaval, several air pollution control authorities in the Northeastern states were forced to relax hard-won air quality standards during the winter of 1972. The authorities did so by granting variances to their sulfur content standards for residual fuel oil. This paper examines the institutional characteristics of these variance policies from an economic incentive standpoint. After setting up desirable structural criteria for institutional design of such crisis policies, the authors examine the experience of the winter of 1972 and arrive at policy guidelines which recommend themselves for consideration in future periods of fuel oil shortages.     

Status and Problems of Regenerable Flue Gas Desulfurization Processes

Fourteen sulfur and/or sulfuric acid producing regenerate FGD processes were discussed at the 1974 FGD Symposium in Atlanta. During the period elapsed since then, considerable status change has occurred on many of these regenerable processes. Other regenerable processes which were not as well known during 1974 have surfaced in 1975. The problems of obtaining reducing gases (hydrogen sulfide, carbon monoxide, and hydrogen) for the reduction of sulfur dioxide product streams to elemental sulfur have become severe due to shortages of natural gas or other petroleum based feedstock. A new sulfur producing process which employs CO and H₂ directly (rather than the H₂S required for liquid and vapor base Claus reactions) is gaining attention. This paper discusses briefly: (1) the announced status of the many regenerable FGD processes, (2) the problem of reductant gas supply, and (3) the effect on FGD processes of using coal based reducing gas instead of reformed natural gas.     

Results of Field Measurements of Industrial Particulate Sources and Electrostatic Precipitator Performance

This paper presents results of source size distribution measurements over the size range from 0.1 μm to 5 μm for six classes of particulate sources and fractional efficiency measurements on five full scale electrostatic precipitators and one pilot scale precipitator. The precipitators all showed moderately high to high particulate collection efficiencies for particles having diameters larger than a few micrometers or smaller than a few hundredths of a micrometer and a minimum in collection efficiency for particles having diameters of a few tenths of a micrometer.     

Characterization of Particulates from Power Plants

The emphasis on participate control from industrial processes has been shifted recently towards fine particulates, having diameters less than 3 microns. There exists an urgent need for more scientific information of fine particle characterization.^1,2 Coal and oil fired power plants are among the largest anthropogenic point sources of particulate matter.³ Limited knowledge is available on particle size distribution and trace metal composition in power plant emissions.^4-7 The morphological properties of particle emissions have been largely neglected. In this report we present some information on particle characteristics for an oil-fired and coal-fired power plant.     

Weekday-Weekend Pollutant Studies of the Los Angeles Basin

Pollutant data from the Los Angeles Basin were analyzed for weekday-weekend differences for the smog months of June through September 1972 and 1973. The pollutants investigated were oxidant, NO, NO₂, total hydrocarbons (HC), CO, and particulates. In order to maintain the diurnal variation, the concentration percentiles were calculated for each weekday and weekend hour.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

Biochemical and Physiological Detection of Sulfur Dioxide Injury to Pea Plants (Pisum sativum)

Biochemical and physiological experiments were conducted on pea plants (Pisum sativum) continuously exposed in growth chambers to SO₂ gas for 18 days. S0₂ gas concentrations were 0.1, 0.15, and 0.25 ppm. In plants exposed to 0.1 and 0.15 ppm it was clearly demonstrated that there was a greater accumulation of inorganic sulfur, a reduced buffer capacity of the cells relative to H-ions, and a stimulation of glutamate dehydrogenase activity. The only macroscopic symptom seen was slight chlorosis of the older leaves. There was only a slight decrease in fresh and dry weights of these plants compared to the control plants whereas in the group of plants exposed to 0.25 ppm SO₂ foliage necrosis was considerable. In addition, there was a marked reduction in the fresh and dry weights of the latter plants. However, the relationship among accumulated inorganic sulfur, reduced buffer capacity, and increased glutamate dehydrogenase activity as seen for the lower S0₂ concentrations was close. Accordingly, if might be possible to use these three parameters to diagnose S0₂ injury before any significant symptoms appear. In the case of severe SO₂ injury there was a marked increase in glutamine and ammonia concentrations suggesting that these factors in addition to the above could be used in diagnosing severe SO₂ injury. There was no significant difference between plants treated with 0.1 or 0.15 ppm SO₂ and control plants in the contents of K, Ca, P, and N fractions. Therefore, these factors would not be useful in the early detection of SO₂ injury.