Differences and similarities of gas and dust explosions: A critical evaluation of the European ‘ATEX’ directives in relation to dusts

Explosive gas mixtures and explosive dust clouds, once existing, exhibit similar ignition and combustion features. However, there are two basic differences between dusts and gases which are of substantially greater significance in design of safety standards than these similarities. Firstly, the physics of generation and up-keeping of dust clouds and premixed gas/vapour clouds are substantially different. This means that in most situations where accidental explosive gas clouds may be produced quite readily, generation of explosive dust clouds would be highly unlikely. Secondly, contrary to premixed gas flame propagation, the propagation of flames in dust/air mixtures is not limited only to the flammable dust concentration range of dynamic clouds. The state of stagnant layers/deposits offers an additional discrete possibility of flame propagation.

The two European Directives 94/9/EC (1994) and 1999/92/EC (1999) primarily address gases/vapours, whereas the particular properties of dusts are not addressed adequately. Some recent IEC and European dust standards resulting from this deficiency are discussed, and the need for revising the two directives accordingly is emphasized.     

Off-site emergency scenario, a case study from a LPG Bottling Plant

After Bhopal disaster, emergency planning in an industrial area has become inevitable. The off-site emergency plan is an integral part of any major hazard control system. Boiling Liquid Expanding Vapour Explosion (BLEVE) leads to fatal consequences. This paper highlights some salient features of the emergency scenario, which ultimately leads to fireball with enormous pressure wave all around.     

Experimental Verification of the Computerized Method for Work Space Optimization in Conditions of Static Work

The aim of this study was to verify a theoretical model for upper extremity work space optimization. In order to do that, experimental studies were conducted in which two parameters of the electromyography (EMG) signal were analyzed: AMP (amplitude calculated as Root Mean Square) and SZC (coefficient of the slope of the regression line between time and Zero Crossing values). Values of forces in muscles (parameter MOD) were calculated from theoretical studies. A comparison of experimental (AMP, SZC) and theoretical (MOD) parameters was performed by analyzing the coefficient of correlation between those parameters and differentiation of muscular load according to external load value. Analysis showed that the theoretical and experimental results are in step, which means that the developed model can be used for upper extremity work space optimization.     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.     

Experimental investigation of hydrogen–air deflagrations and detonations in semi-confined flat layers

This paper presents results of an experimental investigation on the deflagration and deflagration-to-detonation transition (DDT) in an obstructed (blockage ratio BR = 50%), semi-confined flat layer filled with uniform hydrogen–air mixtures. The effect of mixture reactivity depending on flat layer thickness and its width is studied to evaluate the critical conditions for sonic flame propagation and the possibility for detonation onset. The experiments were performed in a transparent, rectangular channel with a length of 2.5 m. The flat layer thickness was varied from 0.06 to 0.24 m and the experiments were performed for different channel widths of 0.3, 0.6 and 0.9 m. The experimental results show flame velocity vs. hydrogen concentration for different thicknesses and widths of the semi-confined flat layer. Three different flame propagation regimes were observed: slow subsonic flame (M << 1), sonic deflagration (M ～ 1) and detonation (M >> 1). It is shown that flame acceleration (FA) to sonic speed is independent of the width of the flat layer. The critical expansion ratio for effective flame acceleration to sonic speed was found to be linearly dependent on the reciprocal layer thickness.     

Assessment of an accidental vapour cloud explosion: Lessons from the Indian Oil Corporation Ltd. accident at Jaipur,India

On 29 October 2009, at 19:30 IST, a devastating vapour cloud explosion occurred in a large fuel storage area at the Indian Oil Corporation (IOC) Depot in Jaipur, India, generating significant blast pressure. As a consequence of this explosion, the entire installation was destroyed, buildings in the immediate vicinity were heavily damaged, and windowpane breakages were found up to 2 km from the terminal. The IOC estimated that the total loss from the fire and explosion was approximately INR 2800 million.Ironically, as a storage site, the Jaipur terminal was not highly congested, and thus was not considered to have adequate potential for a vapour cloud explosion (VCE). Nevertheless, the prima facie evidences indicate that this was a case of VCE. Therefore, the main objective of this study is to quantify the potential overpressures due to vapour cloud explosions (VCEs) using the Process Hazard Analysis DNV Norway based PHAST 6.51 Software. The results are validated by the extent of the damage that had occurred. The estimation of the VCE shows that a maximum 1.0 bar overpressure was generated in the surrounding area. The initial assessment of the accident data roughly estimates the release mode, time, and amount of vaporized fuel. A more accurate estimate has been obtained by modelling the dispersion of vapour clouds in the surrounding atmosphere, which reveals trends and relationships for the occurrence of vapour cloud explosions.     

Status of air pollution in Beijing

A study has been made on elements organic constituents, TSP, SO2,NO2 of atmospheric pollutants in Beijing. 17 elements, and some PAHs, e. g. B(a)P, B(b, j, k)P, and B(g, h, i)P, in airborne particles by X-ray fluorescence spectroscopy and HPLC, GC/MS, have been determined respectively. It has been shown that the elements Pb, Zn, S and Cu were more enriched in fine particles and different valence states of sulfur at various sites. It was found that the concentrations of S6+ and S2-were more than 85% and less than 15% of the total sulfur respectively. Concentrations of major PAHs and sulfur-containing compounds increased in winter and in urban area. High values for Pb and Zn in city, Fe and Mn at industrial area and Cu, Al rural sites were obtained respectively. This implies the functions of different elemental sources of various sites. Thus, elements can be from distingushed anthropogenic and natural sources.The main contribution of SO2 was found of to have same seasonal variation as the anthropogenic el     

Does the financing of extended producer responsibility influence economic growth?

The question of how the financing of Extended Producer Responsibility (EPR) affects the overall performance of the economy is important as products covered by EPR comprise an increasing part of the economy. In this paper, an Overlapping Generations (OLG) model with endogenous growth is applied to the case and a comparison between two financing schemes, an insurance solution and a pay-as-you-go (PAYG) solution, is made with respect to the effect on the level of production, the growth rate, the impact of a productivity shock and the risk exposure. It is found that in the case of a funded solution, both the level of production and the growth rate in production is higher than in the PAYG case, and the short-run effect of productivity shock is bigger. The policy indication is clear: EPR should be attached to a financing scheme if welfare is to be maximised.     

Cleaner tanning practices for tannery pollution abatement: Role of enzymes in eco-friendly vegetable tanning

Concern about pollution related problems in the global scenario are persuading all the processing industries to adopt cleaner manufacturing practices. Thus, the leather industry is also under pressure to look for effective alternative tanning materials for chromium. Natural products like vegetable tannins are regaining importance. However, there are limitations in the use of vegetable tanning materials because of its high organic load in the effluent, which are difficult to degrade leading to high chemical oxygen demand (COD). Moreover, conventional vegetable tanning process requires partial pickling that involves the use of sodium chloride, to suppress osmotic swelling. This results in very high amount of total dissolved solid (TDS) content in wastewaters. In this investigation, an attempt has been made to design an eco-friendly vegetable tanning process combining pickle-free tanning and application of proteolytic enzymes to improve the exhaustion of vegetable tannins. Such an approach has resulted in more than 95% tannin exhaustion in the case of the experimental process, an increase of 10% compared with the conventional vegetable tanning process. The tanned leathers showed slight improvement in hydrothermal stability. Physical and tactile evaluation of experimental leathers has been better than conventionally tanned leathers. Surface colour values illustrated negligible variation in colour and shade between control and experimental leathers. The resultant leather showed opened up, split compact fibre structure that has been well coated, indicating that the enzyme assisted tanning process did not bring about any major change or destruction on the fibre structure of the leathers. The optimized system has been field tested in a commercial tannery. The results showed that the enzyme assisted tanning process is efficient in terms of improved quality of leather and also led to reduction in total solids (TS), chlorides and COD loads. The enzyme assisted tanning system presented appears to be a viable option for combating pollution arising from the conventional vegetable tanning system.