Experimental investigation of outdoor and indoor mean concentrations and concentration fluctuations of pollutants

Tracer gas was released upwind of a two-compartment complex shaped building under unstable atmospheric conditions. The mean wind direction was normal to or at 45° to the long face of the building. The general patterns of concentration distribution on the building external walls and inside the building were analysed and the influence of natural and mechanical ventilation on indoor concentration distributions was discussed. Mean concentration levels, as well as the concentration fluctuation intensity, were higher on the windward walls of the building, although concentration levels varied along each wall. Concentration fluctuations measured inside the building were lower than those measured outside. Inside the two compartments of the building, the time series of concentrations had a similar general behaviour; however, gas concentrations took approximately 1.5 times longer to reach the mean maximum concentration value at the downwind compartment 02 while they also decreased more rapidly in the upwind compartment 01 after the source was turned off. The highest indoor concentration and concentration fluctuation values were observed at the detectors located close to the windward walls, especially when the building windows were open. Experiments with and without natural ventilation suggested that infiltration and exfiltration of contaminants is much faster when the building windows are open, resulting to higher indoor concentration levels. Furthermore, mechanical ventilation tends to homogenize concentrations and suppress concentration fluctuations, leading to lower maximum concentration values.     

Stepwise calibration of the activated sludge model no. 1 at a partially denitrifying large wastewater treatment plant

Activated sludge modeling technology is maturing; however, currently, there exists a great need to increase its use in daily engineering practice worldwide. A good way for building the capacities of the practitioners is to promote good modeling practices and standardize the protocols. In this study, a systematic procedure was proposed to calibrate the Activated Sludge Model No. 1 (ASM1) at a large wastewater treatment plant, by which the model adequately predicted the quality of the effluent and the sludge quantities. A hydraulics model was set up and validated through a tracer test. The Vesilind settling constants were measured and combined with the default value of the flocculent zone settling parameter, to calibrate the clarifiers. A virtual anoxic tank was installed in the return activated sludge to mimic the denitrification occurring in the settlers. In ASM1, the calibrated parameters were only two influent chemical oxygen demand fractions and one kinetic constant (oxygen half-saturation coefficient).     

Evolution of organic matter during composting of different organic wastes assessed by CPMAS 13C NMR spectroscopy

In this paper, the evolution of organic matter (OM) during composting of different mixtures of various organic wastes was assessed by means of chemical analyses and CPMAS ¹³C NMR spectroscopy measured during composting. The trends of temperatures and C/N ratios supported the correct evolution of the processes. The CPMAS ¹³C NMR spectra of all composting substrates indicated a reduction in carbohydrates and an increase in aromatic, phenolic, carboxylic and carbonylic C which suggested a preference by microorganisms for easily degradable C molecules. The presence of hardly degradable pine needles in one of the substrates accounted for the lowest increase in alkyl C and the lowest reduction in carbohydrates and carboxyl C as opposite to another substrate characterized by the presence of a highly degradable material such as spent yeast from beer production, which showed the highest increase of the alkyl C/O-alkyl C ratio. The highest increase of COOH deriving by the oxidative degradation of cellulose was shown by a substrate composed by about 50% of plant residues. The smallest increases in alkyl C/O-alkyl C ratio and in polysaccharides were associated to the degradation of proteins and lipids which are major components of sewage sludge. Results obtained were related to the different composition of fresh organic substrates and provided evidence of different OM evolution patterns as a function of the initial substrate composition.     

Biodegradable Water Soluble Copolymer for Antimicrobial Applications

Synthesis and characterization of novel biodegradable, water soluble and optically active DL-malic acid (DMA) and citric acid (CA) copolymers were studied for possible use as antibacterial agents. The copolymers were synthesized by direct bulk melt condensation in the absence of a catalyst above 150 °C. Characterization of obtained copolymers was carried out with the help of infrared absorption spectra, differential scanning calorimetry and thermo gravimetric analysis. The antibacterial activity of copolymers against bacteria was investigated. The results obtained shows the above copolymers possess a broad wound dressing activity against different types of bacteria and may be useful as antibacterial agents.     

Determination of microbiological contamination,antibacterial and antioxidant activities of natural plant hazelnut (Corylus avellana L.) pollen

The aim of our study is to determine microbial contamination, antibacterial and antioxidant activities of 14 pollen samples of Corylus avellana collected from different locations in Slovakia. Microbiological analysis was carried out in two steps: microbiological assays and studies of antibacterial activity of pollen extracts. The antimicrobial properties of pollen extracts were carried out with the disc-diffusion method. Methanol (70%), ethanol (70%) and distilled water were used for pollen extracts. Five strains of bacteria such as gram-negative (Salmonella enterica subsp. enterica CCM 3807, Escherichia coli CCM 2024, and Yersinia enterocolitica CCM 5671) and gram-positive (Staphylococcus aureus CCM 2461 and Bacillus thuringiensis CCM 19T) were tested. Antioxidant activity of pollen extracts was determined by the DPPH method. Bacterial analysis includes the determination of the total bacterial count ranged from 4.08 to 4.61 log CFU g^?1, mesophilic aerobic bacteria ranged from 3.40 to 4.89 log CFU g^?1, mesophilic anaerobic bacteria ranged from 3.20 to 4.52 log CFU g^?1, coliform bacteria ranged from 3.30 to 4.55 log CFU g^?1, yeasts and filamentous fungi ranged from 3.00 to 3.56 log CFU g^?1. Microscopic filamentous fungi Aspergillus spp., Alternaria spp., Penicillium spp., Cladosporium spp., Rhizopus spp., and Paecylomyces spp. were isolated from hazelnut pollen. Yersinia enterocolitica was the most sensitive strain among ethanolic and methanolic pollen hazelnut extracts. Staphylococcus aureus was the most sensitive strain against aqueous hazelnut pollen extracts. We determined the following sensitivity against ethanol pollen extracts respectively: Yersinia enterocolitica?>?Salmonella enterica?>?Staphylococcus aureus?>?Bacillus thuringiensis?>?Escherichia coli. Methanol pollen extracts had shown following sensitivity: Yersinia enterocolitica?>?Salmonella enterica?>?Escherichia coli?>?Staphylococcus aureus?>?Bacillus thuringiensis. Aqueous extracts had shown the following sensitivity: Staphylococcus aureus?>?Salmonella enterica?>?Escherichia coli?>?Bacillus thuringiensis?>?Yersinia enterocolitica. Hazelnut pollen extracts have over 82% antioxidant capacity in samples from non-urban zones. An elevated level of antioxidant potential in the pollen is determined by its biological properties conditioned by biologically active substances. DPPH method allowed characterizing pollen as a source of antioxidants.     

Microbial fuel cells: Advances in electrode modifications for improvement of system performance

There is an increasing trend to conduct the researches related to Microbial Fuel Cells (MFCs) in the recent years. Limited power output has been the major obstacle for the practical application and upscaling of MFCs. Attempts have been made on electrode modifications such as anode treatments, cathode modifications with catalysts and bio cathodes developments to produce varying degrees of improved output current depending upon the types of modifications. Power density and Coulombic efficiency have been considered as the important parameters to analyze the system performances. This paper overviews on the advances made in MFCs’ researches focusing on different types of electrodes modifications along with the involved methodology. Furthermore, the system performances of different modified MFCs are compared in terms of the power density and the Coulombic efficiency.     

A comparison of pretreatments on release of sugars from sweet sorghum bagasse for bioethanol production

Dilute acid pretreatment and steam pretreatment were evaluated for maximum sugars release and ethanol production from sweet sorghum bagasse (SSB). The fermentation potential of the condensate and hydrolysate obtained from steam pretreatment (10 kg/cm², 10 minutes) and dilute acid hydrolysis (1% (w/w) sulphuric acid, 25% substrate loading) respectively, was checked with Pichia stipitis NCIM 3497 and Debaryomyces hansenii sp. Ethanol production and yield using acid hydrolysate was higher with Debaryomyces hansenii sp. (28.4 g/L and 0.37 g/g respectively) as compared with Pichia stipitis NCIM 3497 (21.9 g/L and 0.29 g/g respectively).     

A case study of an isolated wind powered electricity system meeting 100% of local demand

Using meteorological and electricity demand data for a 4-year period, electricity demand in Shetland was modeled to provide an estimate of the demand over a 30-year period from 1 January 1981. That modeled demand was then compared to estimated wind power output over the same period using the WAsP model. The wind farm output was estimated for a range of sizes of wind farm up to the consented 370 MW Viking Wind Farm in Shetland. Some wind power was available for 94% of the time and the 370 MW wind farm would meet 100% of demand for nearly 80% of the time. The statistics of single and accumulated deficits were calculated for a range of wind farms and estimates of the amount of additional generation capacity and additional power requirements were assessed. The study suggests that with storage, wind power in Shetland could meet all electricity demand in Shetland at around £130 to £150/MWh (excluding subsidy) and with a grid connection allowing the sale of excess power, those costs could be reduced.     

Leaching behavior of some demolition wastes

Demolition wastes may be used in different civil engineering applications as road constructions, concrete, and embankments or landfill. Regardless its application, leaching tests of the waste should be carried out to assess concentrations of pollutants. Concrete, brick and mixture of concrete, bricks, tiles and ceramics wastes were subject to percolation test—CEN/TS 14405, and batch test—SR EN 12457. The leachates were analyzed with respect to concentration of inorganic elements—arsenic, barium, cadmium, chromium, copper, mercury, molybdenum, nickel, lead, selenium, zinc, fluoride, chloride and sulfate, and organic compounds (phenol index). The concentrations of elements in leachates were compared with the limit values of European regulation for the acceptance of inert wastes at landfills. Generally, the releases of inorganic species in leachates were below limits values. Some waste leachates obtained by percolation and batch test had high values for phenol index.     

Improving photostability and efficiency of polymeric luminescent solar concentrators by PMMA/MgO nanohybrid coatings

MgO nanocrystals were synthesized and doped with different concentrations in poly(methylmethacrylate) (PMMA) to prepare hybrid organic-inorganic coatings based on polymer nanohybrid thin films. The nanoparticles were found to be spherical with 62 nm diameter as determined by X-ray diffraction (XRD) and atomic force microscope (AFM). The coatings were characterized by spectroscopic tools such as optical absorption, transmission and fluorescence spectroscopy. The prepared nanohybrid films were spin-coated on cost-effective luminescent PMMA substrates doped with highly efficient luminescent dyes luminescent solar concentrators (LSCs). The outdoor photostability tests demonstrated enhanced protection against UVA radiation for coated LSCs compared to bare LSC substrates. The current–voltage characteristics of commercially produced LSC prototypes showed that the poor UV response of monocrystalline silicon solar cell can be improved by for LSCs coated by PMMA/MgO nanohybrid films which act as luminescent down shifting layer (LDSL).