Development and validation of the volatile correction model for PM10 – An empirical method for adjusting TEOM measurements for their loss of volatile particulate matter

EU Directives stipulate that PM₁₀ should be measured using the gravimetric reference method as laid out in EN12341 [CEN, 1998. Air Quality – Determination of the PM₁₀ Fraction of Suspended Particulate Matter – Reference Method and Field Test Procedure to Demonstrate Reference Equivalence of Measurement Methods. European Committee for Standardisation], or an equivalent method as demonstrated using EC guidance [EC, 2005. Demonstration of Equivalence of Ambient Air Monitoring Methods. European Commission Working Group on Guidance for the Demonstration of Equivalence]. There is however a conflict between the requirement to measure PM₁₀ using the gravimetric reference method and the need for rapid public reporting, and many member states, including the UK, rely on non-gravimetric techniques to measure PM₁₀. In the UK the majority of PM₁₀ measurements are made using the Tapered Element Oscillating Microbalance (TEOM), which does not meet the equivalence criteria [Harrison, D., 2006. UK Equivalence Programme for Monitoring of Particulate Matter. Defra, London]. The implied need to upgrade or replace TEOMs with an equivalent automated measurement technique has significant cost implications. The model described in this paper was based on analysis of daily mean measurements of PM₁₀ by the Filter Dynamics Measurement System (FDMS) and the TEOM at UK sites. It uses the FDMS measurement of the volatile component of PM₁₀ (referred to here as FDMS purge) to correct for differences in the sensitivity to volatile PM₁₀ between the TEOM and the EU gravimetric reference method. The model equation for the correction of TEOM PM₁₀ measurements is: TEOM_VCM = TEOM ? 1.87 FDMS purge due to the regional homogeneity of volatile PM, the FDMS purge concentration may be measured at a site distant to the TEOM, allowing the possibility of using a single FDMS instrument to correct PM₁₀ measurements made by several TEOMs in a defined geographical area. The model was assessed against the criteria for the EC Working Group's Guidance for the Demonstration of Equivalence of Ambient Air Monitoring Methods [EC, 2005. Demonstration of Equivalence of Ambient Air Monitoring Methods. European Commission Working Group on Guidance for the Demonstration of Equivalence]. The model satisfies the equivalence criteria using remote FDMS purge measurements for distances up to 200 km (in 22 out of 23 data sets). These data provide strong evidence that the model is a viable tool for correcting measurements from TEOM instruments on the national and local government networks.     

Filter light attenuation as a surrogate for elemental carbon

Light attenuation (b(att)) measured from filter light transmission is compared with elemental carbon (EC) measurements for more than 180,000 collocated PM2.5 (particulate matter [PM] < or = 2.5 microm in aerodynamic diameter) and PM10 (PM < or = 10 microm in aerodynamic diameter) samples from nearly 200 U.S. locations during the past 2 decades. Although there are theoretical reasons for expecting highly variable relationships between b(att) and EC (such as the effects of "brown carbon" and iron oxides in PM2.5), reasonable correlations are found. These correlations are not a strong function of season or location (e.g., rural vs. urban). Median EC concentrations can be predicted from filter transmittance measurements to within +/- 15-30%. Although EC predicted from b(att) shows larger uncertainties (30-60%), especially at concentrations less than 0.3 microg/m3, the consistent mass absorption efficiency (sigm(att)) derived from the regression analysis demonstrates the feasibility of using b(att) as a surrogate for EC. This study demonstrates that a constant factor of 0.1 g/m2 (equivalent to the 10 m2/g sigma(att) used in the Interagency Monitoring of Protected Visual Environments chemical extinction formula) can be used to estimate EC concentrations from b(att) through a Teflon-membrane filter sample. Greater accuracy is achieved with site-specific sigma(att) derived from a period with collocated EC measurements.     

Source profiles for industrial, mobile, and area sources in the Big Bend Regional Aerosol Visibility and Observational study

Representative PM2.5 and PM10 source emissions were sampled in Texas during the Big Bend Regional Aerosol Visibility and Observa (BRAVO) study. Chemical source profiles for elements, ions, and carbon fractions of 145 samples are reported for paved and unpaved road dust, soil dust, motor vehicle exhaust, vegetative burning, four coal-fired power stations, an oil refinery catalytic cracker, two cement kilns, and residential meat cooking. Several samples were taken from each emitter and source type, and these were averaged by source type, and in source subgroups based on commonality of chemical composition. The standard deviation represents the variability of the chemical mass fractions. BRAVO profiles differed in some respects from profiles measured elsewhere. High calcium abundances in geological dust, high selenium abundances in coal-fired power stations, and high antimony abundances in oil refinery catalytic cracker emissions were found. Abundances of eight thermally evolved carbon fractions [Atmos. Environ. 28 (15) (1994) 2493] differ among combustion sources, and a Monte Carlo simulation demonstrates that these differences are sufficient to differentiate among several carbon-emitters.     

Use of Tracer Gas for Direct Calibration of Emission-Factor Measurements in a Traffic Tunnel

ABSTRACT

Pollutant measurements in traffic tunnels have been used to estimate motor-vehicle emissions for several decades. The objective in this type of study is to use the traffic tunnel as a tool for characterizing motor vehicles rather than seeking a tunnel design with acceptably low pollutant concentrations. In the past, very simple aerodynamic models have been used to relate measured concentrations to vehicle emissions. Typically, it is assumed that velocities and concentrations are uniform across the tunnel cross section. In the present work, a vehicle emitting a known amount of sulfur hexafluoride (SF₆) was driven repeatedly through a 730-m-long traffic tunnel in Vancouver, Canada. Comparing the measured SF₆ concentrations to the known emission rates, it is possible to directly assess the accuracy of the simple tunnel aerodynamic models typically used to interpret tunnel data. Correction factors derived from this procedure were then applied to measurements of carbon monoxide and other pollutants to obtain gram-per-kilometer emission factors for vehicles. Although the specific correction factors measured here are valid only for the tunnel tested, the magnitude of the factors (up to two or more) suggests that the phenomena observed here should be considered when interpreting data from other tunnels.     

Multilayer thin film silicon solar cells

New multilayer solar cells combine three innovations to produce a unique device structure which allows high efficiency cells to be designed on low quality material. The first innovation is the use of the multilayer structure itself, which provides the tolerance to low quality material. The second is the use of the well-proven buried contact technology. The third innovation is a simple technique for connecting cells in series which relies on having grooves of opposite polarity either overlapping or in close proximity to each other. These three innovations combine to produce a manufacturing approach with a small number of processing steps able to produce a product with a high energy conversion efficiency using low quality starting material. The unit of production is a large module of approximately 1 m² in area rather than the smaller 100 cm² cells which are the present commercial norm .     

改变生产与消费方式:已经取得的进展与存在的挑战

在贫困不断减少以及经济持续增长的情况下,生产与消费方式必然会由不可持续型向可持续型转变.由于这会使人们显著改变思想观念与行为方式,因此需要解决生产者与消费者责任问题.清洁生产是企业社会责任的核心.目前UNEP已收到多项建议,其中包括发展清洁生产与可持续消费指标以及增进多方合作性举措.     

Measuring differences between overlapping but unpaired spatial surveys using a geographic information system

To compare the results from two overlapping but unpaired synoptic surveys, a method using a geographic information system is proposed. The new method uses a GIS to create (i) minimum convex polygons (MCP) enclosing each set of survey data and (ii) Voronoi tesselations assigning area weights to each datum. The pairs of MCP and Voronoi maps are overlaid to produce a mosaic of polygons each with one datum assigned from each survey. The differences between the pairs weighted by the polygon areas provides the basis for statistical testing. Area-weighted means and variances of paired differences are computed and a z-statistic measures the significance of differences for the whole intersection area. A cross-product autocorrelation statistic provides an assessment of the spatial distribution of differences. Alternate, conventional methods are compared with the new method: analysis of variance (ANOVA), analysis of covariance (ANCOVA), and contour overlays. The four methods were applied to the comparison of two macrobenthic surveys conducted in Lake Erie. Measures for five different taxa were examined. The ANOVA and ANCOVA methods found many significant differences between surveys. Both methods were judged inappropriate as sampling data are not expected to be drawn from normally-distributed populations in spatial surveys. Differences between surveys were detected but were difficult to assess using contour overlays. The new method only found a significant difference in one taxon, an expected difference as members of that taxon were absent from most sites in one survey.     

The Risks from Flooding: Which Risks and Whose Perception?

Four main groups are considered in relation to the risk from flooding: the engineers involved in the design of flood alleviation schemes, emergency planners, the public, including both the population at risk from flooding and the rest of the population who will bear all or most of the cost of flood alleviation schemes and the researchers, such as geographers and economists concerned with flood hazards and scheme appraisal. It is argued that these different groups vary significantly in their selection and definition of risks from flooding as a focus of concern and that their definition of risk influences their expectations about future events and the appropriate response to those events. But the different groups share two tendencies: the expectation that the future will be a replication of the past; and the neglect of "uncertain uncertainties" in favour of known uncertainties of risk.     

Determination of MTBE in a recreational harbor using solid-phase microextraction

Discovery of the fuel additive methyl tert-butyl ether (MTBE) in groundwater, surface water, and stormwater has prompted studies of its sources, transport and fate. More limited data, however, is available on the extent of contamination of coastal waters, as well as the persistence of MTBE in the marine environment. We apply here the combination of solid phase microextraction and gas chromatography-mass spectrometry to the detection of sub-to-low microgram/l concentrations of MTBE in seawater samples. Analysis of samples collected at the Marina del Rey harbor, a shallow recreational harbor near Los Angeles, CA, show MTBE contamination in the low microgram/l level. MTBE measurements were made at different depths, from the surface to the bottom, at five sites within the harbor during months showing no measurable precipitation. The highest concentration of MTBE (18 microgram/l) was found at the boat launching ramp, and the lowest (0.2 microgram/l) near the harbor entrance, approximately 2.3 km from the ramp. The levels of MTBE measured, as well as their variation over the study period, are fully consistent with recreational boating as the primary source of contamination. No evidence for MTBE contamination from the adjacent stormwater control channel was noted.