A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

A techno-economic comparison of fluidized bed gasification of two mixed plastic wastes

A comparison between the most promising design configurations for the industrial application of gasification based, plastics-to-energy cogenerators in the 2-6 MWe range is presented. A pilot scale bubbling fluidized bed air gasifier, having a feeding capacity of 100 kg/h, provided experimental data: the syngas complete composition, the characterization of the bed material, the entrained fines collected at the cyclone and the purge material from the scrubber. Mass and energy balances and material and substance flow analyses have been therefore drawn to assess and compare design solutions utilizing two mixed plastic wastes (MPW) obtained from separate collection of plastic packaging, after different levels of pre-treatments. The related techno-economic performances have been finally estimated on the basis of the manufacturer’s specifications. The study concludes that the MPW obtained after a very simple pre-treatment and fed to a gasifier coupled with a steam turbine is the solution that currently offers the higher reliability and provides the higher internal rate of return for the investigated range of electrical energy production.     

Targeted intervention strategies to optimise diversion of BMW in the Dublin, Ireland region

Urgent transformation is required in Ireland to divert biodegradable municipal waste (BMW) from landfill and prevent increases in overall waste generation. When BMW is optimally managed, it becomes a resource with value instead of an unwanted by-product requiring disposal. An analysis of survey responses from commercial and residential sectors for the Dublin region in previous research by the authors proved that attitudes towards and behaviour regarding municipal solid waste is spatially variable. This finding indicates that targeted intervention strategies designed for specific geographic areas should lead to improved diversion rates of BMW from landfill, a requirement of the Landfill Directive 1999/31/EC. In the research described in this paper, survey responses and GIS model predictions from previous research were the basis for goal setting, after which logic modelling and behavioural research were employed to develop site-specific waste management intervention strategies. The main strategies devised include (a) roll out of the Brown Bin (Organics) Collection and Community Workshops in Dún Laoghaire Rathdown, (b) initiation of a Community Composting Project in Dublin City (c) implementation of a Waste Promotion and Motivation Scheme in South Dublin (d) development and distribution of a Waste Booklet to promote waste reduction activities in Fingal (e) region wide distribution of a Waste Booklet to the commercial sector and (f) Greening Irish Pubs Initiative. Each of these strategies was devised after interviews with both the residential and commercial sectors to help make optimal waste management the norm for both sectors. Strategy (b), (e) and (f) are detailed in this paper. By integrating a human element into accepted waste management approaches, these strategies will make optimal waste behaviour easier to achieve. Ultimately this will help divert waste from landfill and improve waste management practice as a whole for the region. This method of devising targeted intervention strategies can be adapted for many other regions.     

制药废水有机污染物特性分析与处理

分析了某制药企业废水生物处理站进出水中有机污染物的相对分子质量分布和气相色谱—质谱图谱,提出了根据废水水质特性有针对性地确定制药废水处理工艺的新思路.实验结果表明:进出水中的有机污染物主要是相对分子质量小于1 000的物质,且主要来源于车间5排放的COD比重大、水量小的工段废水;采用旋转蒸馏预处理法处理车间5废水,可使...     

Dry and heat stress affects H2S production of Salmonella on selective plating media

The pH of Salmonella pre-enrichment media can become acidic (pH 4.0–5.0) when feeds/ingredients are incubated for 24?h. Salmonella in feed that have been stressed by heat and desiccation exhibit different pH tolerances than non-stressed cultures. Acidic conditions can result in cell injury/death and affect biochemical pathways. In this study, eight serotypes of Salmonella were grown in sterile meat and bone meal that was subjected to desiccation and heat stress. Cultures of non-stressed and stressed isolates were subsequently exposed to acidic pH from 4.0 to 7.0 in 0.5?pH increments (3 replicates/pH increment) in citrate buffer. At 6 and 24?h, serial dilutions were plated in duplicate on XLT-4 (xylose lysine tergitol-4) agar. Four serotypes showed an impaired ability to decarboxylate lysine on XLT-4. This inability to decarboxylate lysine was dependent on isolate, stress status, and incubation time. When the isolates’ ability to decarboxylate lysine was examined using biochemical tests, cultures were found to be able to decarboxylate lysine with the exception of S. Infantis. This suggests that XLT-4 contains a biochemical stressor(s) which affects the rate of decarboxylation by these Salmonella. These results suggest that acidic conditions may influence the detection and confirmation of Salmonella in feed.     

Indicator framework for sustainable production planning and controlling

Production facilities serve to transform raw materials into products, usually with the goal of achieving a designated output, in terms of quantity and quality, with the minimum of cost and labour. With the aid of production planning and controlling (PPC) systems, raw material inputs, and labour can be planned to achieve a determined output of products. In general, the role of environmental and social aspects is neglected in production planning processes. Because of the growing pressure from politics and customers, sustainable production of products is becoming more important. One possibility for supporting sustainable manufacturing is, to integrate sustainable aspects in the production planning process. This paper presents input and output information for current PPC systems and discusses the need for additional information necessary for sustainable PPC. For this approach, a text review of cooperate social responsibility (CSR) reporting indicators provided by the GRI was performed. Based on the text review, an input-output model has been developed for conventional and another one for sustainable PPC systems. Through the comparison of the two input-output models, challenges and requirements for sustainable PPC systems have been defined as a basis for future work and analyses.     

Auxinic herbicides induce oxidative stress on Cnesterodon decemmaculatus (Pisces: Poeciliidae)

Environmental Science and Pollution Research - Pesticides might increase the production of reactive oxygen species (ROS). Dicamba (DIC) and 2,4-dichlorophenoxyacetic acid (2,4-D) are auxinic...     

Effects of atmospheric ammonia and ammonium sulphate on Douglas fir (Pseudotsuga menziesii)

Three-year-old Douglas firs (Pseudotsuga menziesii) were fumigated with 180 microg m(-3) NH3 or clean (charcoal-filtered) air. During these fumigations the plants received 15 mm artificial rain weekly, supplemented with 20, 500 or 2500 micromol litre(-1) (NH4)2SO4. Exposure to NH3 and NH4+ for 14 weeks resulted in a change of the nutrient status of the needles. The most remarkable effect was the increase in the N/K ratio, due to both uptake of N and leaching of K. The action of NH3 was stronger than that of NH4+. Both NH3 and (NH4)2SO4 affected the epicuticular wax layer and decreased mycorhiza frequency. Following fumigation and artificial rain treatments, needles were incubated for 8 h in a medium containing 0, 50, 250, 500 and 2500 micromol litre(-1) (NH4)2SO4. Almost no exchange of Ca, Mg and K for NH4+ was found. Therefore this ion exchange probably explains only a minor part of the changes in nutrient status of the whole trees.