Comparative Response of Indigenously Developed Bacterial Consortia on Progressive Degradation of Polyhydroxybutyrate Film Composites

The global demand of bioplastics has lead to an exponential increase in their production commercially. Hence, biodegradable nature needs to be evaluated in various ecosystems viz. air, water, soil and other environmental conditions to avoid the polymeric waste accumulation in the nature. In this paper, we investigated the progressive response of two indigenously developed bacterial consortia, i.e., consortium-I (C-I: Pseudomonas sp. strain Rb10, Pseudomonas sp. strain Rb11 and Bacillus sp. strain Rb18), and consortium-II (C-II: Lysinibacillus sp. strain Rb1, Pseudomonas sp. strain Rb13 and Pseudomonas sp. strain Rb19), against biodegradation behavior of polyhydroxybutyrate (PHB) film composites, under natural soil ecosystem (in net house). The biodegraded films recovered after 6 and 9 months of incubation were analyzed through Fourier transform infrared spectroscopy and scanning electron microscopy to determine the variations in chemical and morphological parameters (before and after incubation). Noticeable changes in the bond intensity, surface morphology and conductivity were found when PHB composites were treated with C-II. These changes were drastic in case of blends in comparison to copolymer. The potential isolates not only survived, but, also, there was a significant increase in bacterial diversity during whole period of incubation. To the best of our knowledge, it is the first report which described the biodegradation potential of Lysinibacillus sp. as a part of C-II with Pseudomonas sp. against PHB film composites.     

Closing the material cycle of biomass-derived fly ashes: a regional case study of natural ageing in Finland

Journal of Material Cycles and Waste Management - The amount of biomass-derived ashes is expected to rise in the EU due to targets to increase the use of renewable energy resources. To promote the...     

Mechanical Properties of Layered Laminated Woven Bamboo <Emphasis Type="Italic">Gigantochloa Scortechinii</Emphasis>/Epoxy Composites

This study investigated the application of bamboo as a natural composite, in which its potential as a composite material had been examined for 2–6 layers. In precise, the woven bamboo (BW) formed the culm fiber composite with an average of 0.5 mm thickness and 5.0 mm width strip. In addition, this study looked into a specific type of bamboo species known as Gigantochloa Scortechinii (Buluh Semantan), which can be found in Malaysia. This laminated plain BW, which had been reinforced with epoxy (EP), was developed by applying the hand lay-up technique. After that, the specimens were characterized via mechanical analyses, for instance, tensile, flexural, hardness, and impact tests. As a result, the 2-layer BW had displayed rather excellent results chiefly due to the incorporation of epoxy composite, although this is exceptional hardness value.     

The choice of system boundaries for effective long-term management of phosphorus

Journal of Material Cycles and Waste Management - Material flow analysis (MFA) is a well-established tool for supporting decisions on nutrient management. This paper shows the importance of the...     

Modelling and Optimization of Uranium (VI) Ions Adsorption Onto Nano-ZnO/Chitosan Bio-composite Beads with Response Surface Methodology (RSM)

Nano-ZnO-chitosan bio-composite beads were prepared for the sorption of \({\text{UO}}_{2}^{{2+}}\) from aqueous media. The resulting nano-ZnO/CTS bio-composite beads were characterized by TEM, XRD etc. The sorption of \({\text{UO}}_{2}^{{2+}}\) by bio-composite beads was optimized using RSM. The correlation between four variables was modelled and studied. According to RSM data, correlation coefficients (R²?=?0.99) and probability F-values (F?=?2.24?×?10^??10) show that the model fits the experimental data well. Adsorption capacity for nano-ZnO/CTS bio-composite beads was obtained at 148.7 mg/g under optimum conditions. The results indicate that nano-ZnO/CTS bio-composite beads are appropriate for the adsorption of \({\text{UO}}_{2}^{{2+}}\) ions from aqueous media. Also, the suitability of adsorption values to adsorption isotherms was researched and thermodynamic data were calculated.     

A numerical study on the effects of EGR and spark timing to combustion characteristics and NOx emission of a GDI engine

EGR is one of the most significant strategies for reducing especially nitrogen oxides (NO_x) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NO_x emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NO_x emissions.     

Reducing the risk of invasive forest pests and pathogens: Combining legislation,targeted management and public awareness

Intensifying global trade will result in increased numbers of plant pest and pathogen species inadvertently being transported along with cargo. This paper examines current mechanisms for prevention and management of potential introductions of forest insect pests and pathogens in the European Union (EU). Current European legislation has not been found sufficient in preventing invasion, establishment and spread of pest and pathogen species within the EU. Costs associated with future invasions are difficult to estimate but past invasions have led to negative economic impacts in the invaded country. The challenge is combining free trade and free movement of products (within the EU) with protection against invasive pests and pathogens. Public awareness may mobilise the public for prevention and detection of potential invasions and, simultaneously, increase support for eradication and control measures. We recommend focus on commodities in addition to pathways, an approach within the EU using a centralised response unit and, critically, to engage the general public in the battle against establishment and spread of these harmful pests and pathogens.     

Conceptualizing and communicating management effects on forest water quality

We present a framework for evaluating and communicating effects of human activity on water quality in managed forests. The framework is based on the following processes: atmospheric deposition, weathering, accumulation, recirculation and flux. Impairments to water quality are characterized in terms of their extent, longevity and frequency. Impacts are communicated using a “traffic lights” metaphor for characterizing severity of water quality impairments arising from forestry and other anthropogenic pressures. The most serious impairments to water quality in managed boreal forests include (i) forestry activities causing excessive sediment mobilization and extirpation of aquatic species and (ii) other anthropogenic pressures caused by long-range transport of mercury and acidifying pollutants. The framework and tool presented here can help evaluate, summarize and communicate the most important issues in circumstances where land management and other anthropogenic pressures combine to impair water quality and may also assist in implementing the “polluter pays” principle.