A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

Economic development and environmental protection: an ecological economics perspective

This paper argues on both theoretical and empirical grounds that, beyond a certain point, there is an unavoidable conflictbetween economic development (generally taken to mean 'materialeconomic growth') and environmental protection. Think for a moment of natural forests, grasslands, marine estuaries, salt marshes, and coral reefs; and of arable soils, aquifers, mineraldeposits, petroleum, and coal. These are all forms of 'natural capital' that represent highly-ordered self-producing ecosystemsor rich accumulations of energy/matter with high use potential (low entropy). Now contemplate despoiled landscapes, eroding farmlands, depleted fisheries, anthropogenic greenhouse gases,acid rain, poisonous mine tailings and toxic synthetic compounds.These all represent disordered systems or degraded forms of energy and matter with little use potential (high entropy). The main thing connecting these two states is human economic activity. Ecological economics interprets the environment-economyrelationship in terms of the second law of thermodynamics. The second law sees economic activity as a dissipative process. Fromthis perspective, the production of economic goods andservices invariably requires the consumption of available energy and matter. To grow and develop, the economynecessarily 'feeds' on sources of high-quality energy/matter first produced by nature. This tends to disorder and homogenizethe ecosphere, The ascendance of humankind has consistently been accompanied by an accelerating rate of ecological degradation, particularly biodiversity loss, the simplificationof natural systems and pollution. In short, contemporary political rhetoric to the contrary, the prevailing growth-oriented global development paradigm is fundamentally incompatible with long-term ecological and social sustainability. Unsustainability is not a technical nor economic problem as usually conceived, but rather a state of systemic incompatibilitybetween a economy that is a fully-contained, growing, dependent sub-system of a non-growing ecosphere. Potential solutions fly inthe face of contemporary development trends and cultural values.     

Trace Metal Concentration in Roadside Surface Soil and Tree Back: A Measurement of Local Atmospheric Pollution in Abuja, Nigeria

Cadmium, copper, lead, nickel and zinc concentrations were analysed by atomic absorption spectrophotometry in surface soil and tree bark from different districts of Abuja, Nigeria, in order to determine the atmospheric trace metal input in the area.Elevated concentrations of some of the studied metals were observed in the soil and tree bark samples from the commercial/high traffic areas of the city compared to backgroundvalues. In soil samples, the average concentration of the metals were 0.6±0.4, 18.0±4.0, 281±39, 16±4 and66±23 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively, whilst the average concentrations in tree bark were 0.3±0.2, 12±4, 133±32, 13±3 and 61±10 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively. The trend in trace metal levels suggested that automobile emissions are a major source of these metals as the highest concentrations of Pb and Zn were recorded in the commercial areas of the city known for their high traffic densities. The levels of metal in the study area were relativelylow compared to levels found in some larger and older cities in various countries worldwide.     

Application of the benthic index of biotic integrity to environmental monitoring in Chesapeake Bay

The Chesapeake Bay benthic index of biotic integrity (B-IBI) was developed to assess benthic community health and environmental quality in Chesapeake Bay. The B-IBI provides Chesapeake Bay monitoring programs with a uniform tool with which to characterize bay-wide benthic community condition and assess the health of the Bay. A probability-based design permits unbiased annual estimates of areal degradation within the Chesapeake Bay and its tributaries with quantifiable precision. However, of greatest interest to managers is the identification of problem areas most in need of restoration. Here we apply the B-IBI to benthic data collected in the Bay since 1994 to assess benthic community degradation by Chesapeake Bay Program segment and water depth. We used a new B-IBI classification system that improves the reliability of the estimates of degradation. Estimates were produced for 67 Chesapeake Bay Program segments. Greatest degradation was found in areas that are known to experience hypoxia or show toxic contamination, such as the mesohaline portion of the Potomac River, the Patapsco River, and the Maryland mainstem. Logistic regression models revealed increased probability of degraded benthos with depth for the lower Potomac River, Patapsco River, Nanticoke River, lower York River, and the Maryland mainstem. Our assessment of degradation by segment and water depth provided greater resolution of relative condition than previously available, and helped define the extent of degradation in Chesapeake Bay.     

Linking Land Cover and Water Quality in New York City’S Water Supply Watersheds

The Catskill/Delaware reservoirs supply 90% of New York City’s drinking water. The City has implemented a series of watershed protection measures, including land acquisition, aimed at preserving water quality in the Catskill/Delaware watersheds. The objective of this study was to examine how relationships between landscape and surface water measurements change between years. Thirty-two drainage areas delineated from surface water sample points (total nitrogen, total phosphorus, and fecal coliform bacteria concentrations) were used in step-wise regression analyses to test landscape and surface-water quality relationships. Two measurements of land use, percent agriculture and percent urban development, were positively related to water quality and consistently present in all regression models. Together these two land uses explained 25 to 75% of the regression model variation. However, the contribution of agriculture to water quality condition showed a decreasing trend with time as overall agricultural land cover decreased. Results from this study demonstrate that relationships between land cover and surface water concentrations of total nitrogen, total phosphorus, and fecal coliform bacteria counts over a large area can be evaluated using a relatively simple geographic information system method. Land managers may find this method useful for targeting resources in relation to a particular water quality concern, focusing best management efforts, and maximizing benefits to water quality with minimal costs.The United States Environmental Protection Agency through its Office of Research and Development funded and managed the research described here. It has been subjected to Agency’s administrative review and approved for publication as an EPA document.     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

One-year monitoring survey of organic compounds (PAHs, PCBs, TBT), heavy metals and biomarkers in blue mussels from the Arcachon Bay, France

Marine mussels Mytilus sp. were transplanted on a monthly basis in cages over one year to oyster farms and harbours in the Arcachon Bay (France) in order to assess the water quality of the bay. Contaminant levels (organotin compounds, trace metals, PCBs and PAHs) were measured in tissues of transplanted mussels and mussels from a reference station, along with physiological parameters of the mussels (condition indexes, lipid content and dry weight). Four biomarkers (AChE: acetylcholinesterase activity, GST: gluthathione S-transferase activity, CAT: catalase activity and TBARS: thiobarbituric acid-reactive substance content) were also monitored. The remote stations monitored (oyster parks) exhibited no accumulation pattern of pollutants. Their respective concentrations therefore constitute a background level of the contamination in the bay ([TBT]= 30 ng Sn g(-1) dw, [SigmaHAPs]= 100 ng g(-1) dw, [SigmaPCBs]= 35 ng g(-1) dw). The elevated chemical contamination of the largest harbour of the bay, the Arcachon harbour, can be interpreted in terms of persistence of organotin compounds ([SigmaOTs]= 1500-2000 ng Sn g(-1) dw) and PAHs ([SigmaHAPs]= 4500-5000 ng g(-1) dw) in sediments and, to a lesser extent, of direct inputs of copper ([Cu]= 20 microg g(-1) dw in harbours versus 7 in oyster parks) and petrogenic PAHs ([methylphenanthrenes]= 1600 ng g(-1) dw in the dockyard versus 170 at the gas stations), related to the use of copper-based antifouling paints and to dockyard activity, respectively. However, the Arcachon Bay presents a low contamination level by PCBs and metals, including harbour stations. Furthermore, higher levels of other PAHs (particularly alkyl PAHs such as methylphenanthrenes/1600 ng g(-1) dw) not included in the 16 PAHs from the EPA priority list (usually studied in biomonitoring programmes/1500 ng g(-1) dw) in the Arcachon harbour underline the need to integrate these compounds in biomonitoring of highly PAH-polluted areas such as harbours in order to avoid misinterpretation of the biological responses observed. Biomarker responses were not able to discriminate the different chemical contamination levels recorded in the Arcachon Bay and rather reflected changes in environmental factors. Furthermore, the strong intraspecies variability of biological responses could be due to genetic differences of mussels from the Arcachon Bay. It is the first time that such an integrated monitoring is performed in the Arcachon Bay, also taking into account seasonal variations of chemical contents and biomarkers levels in mussel tissues.     

The study of age influence on human bone lead metabolism by using a simplified model and X-ray fluorescence data

Long term lead metabolism in the human body has never been fully understood due to the lack of human data in this area. The technological improvement of bone lead measurement systems has made bone lead data of substantial populations available. In this study, a set of X-ray fluorescence bone lead data was used to test Leggett's lead metabolism model (R. W. Leggett, Environ. Health Perspect., 1993a, 101, 598-616), especially the model of metabolism in bone. The data set includes the bone lead concentration of 539 occupationally exposed workers, of whom 327 were measured twice in five years. The bone lead concentrations of both cortical bone (tibia) and trabecular bone (calcaneus) were obtained by Cd-109 gamma-ray induced XRF measurement. The histories of blood lead concentration for these workers were used to regulate the input file of the model. The results show that the bone lead concentrations predicted by Leggett's model greatly underestimate the measured values, especially for older workers. This data set was then organized into five age groups. A new simplified model was applied to estimate the lead transfer rates between blood and lead compartments for these age groups. The original transfer rates and the new transfer rates are compared, and the differences are discussed. When the transfer rates derived from measured bone lead data were put into the input file of the model to replace the existing parameters, the predicted values were much closer to the measured values for both cortical bone and trabecular bone.     

Exposure and inhalation risk assessment in an aluminium cast-house

To date the exposure, absorption and respiratory health effects of cast-house workers have not been described since most studies performed in the aluminium industry are focused on exposure and health effects of potroom personnel. In the present study, we assessed the external exposure and the absorbed dose of metals in personnel from the aluminium cast house. This was combined with an evaluation of respiratory complaints and the lung function of the personnel. 30 workers from an aluminium casting plant participated and 17 individuals of the packaging and distribution departments were selected as controls. The exposure was assessed by the quantification of total inhalable fume with metal fraction and by the determination of urinary aluminium, chromium, beryllium, manganese and lead concentration. Carbon monoxide (CO), carbon dioxide (CO2), aldehydes and polyaromatic hydrocarbons and man-made mineral fibres concentration were assessed as well. In order to evaluate their respiratory status each participant filled out a questionnaire and their lung function was tested by forced spirometry. Total inhalable fume exposure was maximum 4.37 mg m(-3). Exposure to the combustion gases, man-made mineral fibres and metal fume was well below the exposure limits. Beryllium could not be detected in the urine. The values of aluminium, manganese and lead in the urine were all under the respective reference value. One individual had a urinary chromium excretion above the ACGIH defined biological exposure index (BEI) of 30 microg g(-1) creatinine. There was no significant difference in any of the categories of the respiratory questionnaire and in the results of the spirometry between cast house personnel and referents (Chi-square, all p > 0.05). Exposure in cast houses seem to be acceptable under these conditions. However, peak exposure to fumes cannot be excluded and the potential risk of chromium and beryllium exposure due to the recycling of aluminium requires further attention.