Temporal Trends of Non-sea Salt Sulfate and Nitrate in Wet Deposition in Japan

Temporal trends of non-sea salt (nss-) sulfate and nitrate were analyzed from nationwide precipitation chemistry measurements provided by the Ministry of the Environment (MOE) for the 1988–2002 fiscal years (April–March). The concentrations and deposition of nss-sulfate were found to be decreasing, and those of nitrate were stable or slightly increasing at most sites. These deposition trends were discussed from the viewpoint of emissions of SO₂ and NO_X during the period of interest. Because monitoring techniques have changed in the number of active sites, samplers, and analytical methods during the operation period, the median of all annual depositions measured in Japan in a specific year was selected as the annual representative. The contribution of specific emission sources was also calculated for 1990 on the basis of the nss-sulfate and nitrate deposition in Japan obtained with a model simulation in which the model did not include volcanic emissions from Mt. Oyama, Miyakejima Island, which began to erupt suddenly and violently in 2000. For nss-sulfate, the calculated deposition agrees well with the intensity and trends of the median up to 1999. After 2000, a higher deposition than calculated in the preceding years was evident, which is attributable to the volcanic SO₂ from Mt. Oyama. For nitrate, both the calculated and observed depositions were slightly increasing; however, the calculation was found to exceed the observation.     

Effects of process conditions on nano-dot array formation by thermal dewetting

In this paper, three kinds of self-organization processes for metal nano-dot array fabrication are compared; one is the conventional thermal dewetting, another is thermal dewetting of a grid patterned deposited metal layer, the other is thermal dewetting of a metal layer deposited on a patterned substrate. In these processes, nano plastic forming technique is utilized for patterning of groove grid. Effects of process conditions on nano-dot formation, such as substrate material, deposited metal, thickness of deposited layer, annealing condition, are experimentally studied. Also, effect of grid patterning on improvement of nano-dot array formation is studied. It is shown that grid patterning on a deposited metal layer is effective to improve alignment and configuration of nano-dot array.     

Leaching of indium from obsolete liquid crystal displays: Comparing grinding with electrical disintegration in context of LCA

In order to develop an effective recycling system for obsolete Liquid Crystal Displays (LCDs), which would enable both the leaching of indium (In) and the recovery of a pure glass fraction for recycling, an effective liberation or size-reduction method would be an important pre-treatment step. Therefore, in this study, two different types of liberation methods: (1) conventional grinding, and (2) electrical disintegration have been tested and evaluated in the context of Life Cycle Assessment (LCA). In other words, the above-mentioned methods were compared in order to find out the one that ensures the highest leaching capacity for indium, as well as the lowest environmental burden. One of the main findings of this study was that the electrical disintegration was the most effective liberation method, since it fully liberated the indium containing-layer, ensuring a leaching capacity of 968.5mg-In/kg-LCD. In turn, the estimate for the environmental burden was approximately five times smaller when compared with the conventional grinding.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Recent advances in ionic liquids-based hybrid processes for CO2 capture and utilization

CO₂ capture and utilization (CCU) is an effective strategy to mitigate global warming. Absorption, adsorption and membranes are methods used for CO₂ separation and capture, and various catalytic pathways have also been developed for CO₂ utilization. Although widely researched and used in industry, these processes are energy-intensive and this challenge needs to be overcome. To realize further optimization, novel materials and processes are continuously being developed. New generation materials such as ionic liquids (ILs) have shown promising potential for cost-effective CO₂ capture and utilization. This study reviews the current status of ILs-based solvents, adsorbents, membranes, catalysts and their hybrid processes for CO₂ capture and utilization. The special properties of ILs are integrated into new materials through hybridization, which significantly improves the performance in the process of CCU.