Comparative environmental analysis of waste brominated plastic thermal treatments

The aim of this research activity is to investigate the environmental impact of different thermal treatments of waste electric and electronic equipment (WEEE), applying a life cycle assessment methodology. Two scenarios were assessed, which both allow the recovery of bromine: (A) the co-combustion of WEEE and green waste in a municipal solid waste combustion plant, and (B) the staged-gasification of WEEE and combustion of produced syngas in gas turbines. Mass and energy balances on the two scenarios were set and the analysis of the life cycle inventory and the life cycle impact assessment were conducted. Two impact assessment methods (Ecoindicator 99 and Impact 2002+) were slightly modified and then used with both scenarios. The results showed that scenario B (staged-gasification) had a potentially smaller environmental impact than scenario A (co-combustion). In particular, the thermal treatment of staged-gasification was more energy efficient than co-combustion, and therefore scenario B performed better than scenario A, mainly in the impact categories of "fossil fuels" and "climate change". Moreover, the results showed that scenario B allows a higher recovery of bromine than scenario A; however, Br recovery leads to environmental benefits for both the scenarios. Finally the study demonstrates that WEEE thermal treatment for energy and matter recovery is an eco-efficient way to dispose of this kind of waste.     

Geopolymerisation of silt generated from construction and demolition waste washing plants

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.     

De-novo formation of dioxins and furans and the memory effect in waste incineration flue gases

The formation of dioxin (polychlorinated-rho-dibenzodioxins - PCDD) and furan (polychlorinated dibenzofurans - PCDF) in waste incineration flyash in relation to temperature has been investigated in a bench scale reactor. The PCDD/PCDF released into the exhaust gases of the reactor and trapped in a condensation and vapour phase adsorption system were also determined. The concentrations of PCDD/PCDF in the flyash were analysed in detail for all congeners and isomers including the mono-, di- and tri-PCDD/PCDF. De-novo synthesis of PCDD/PCDF was clearly seen in the flyash with large changes in concentrations of PCDD/PCDF with only small changes in temperature. Exhaust gas PCDD/PCDF were detected at all temperatures, with the maximum emission occurring at a flyash temperature of 350 degrees C, where the equivalent of over 42 times the total dioxin/furan concentration of the original flyash was lost to the vapour phase per unit mass of initial flyash. Although the desorbed species were mainly the lower mono- to tri-congener group of dioxins and furans, the desorbed dioxin/furans had a considerable toxic equivalent value.     

The effects of aeration rate on generated compost quality, using aerated static pile method

To determine the most appropriate composting process in an active municipal solid waste system, an experiment was carried out using a nested design method with three aeration rates. During each aeration rate, parameters such as temperature, pH, EC, carbon-to-nitrogen ratio, NO(3)-N, nitrogen, potassium and phosphorous were measured and the efficiency of different composting processes was evaluated. The result of this study showed that the lower and medium aeration rates had a significant impact on nitrogen, carbon-to-nitrogen ratio and temperature profile, while higher aeration rates led to higher EC values. Furthermore, the thermophilic phase lasted 13, 9 and 4 weeks for the aeration rates of 0.4, 0.6 and 0.9 L min(-1)kg(-1), respectively. Accordingly, it was concluded that starting at a rate of 0.6 L min(-1)kg(-1) during first 2 months (about 9 weeks) of the process and continuing at a rate of 0.4 L min(-1)kg(-1)until the end of composting process would result in lower energy consumption.     

Bench-scale composting of source-separated human faeces for sanitation

In urine-diverting toilets, urine and faeces are collected separately so that nutrient content can be recycled unmixed. Faeces should be sanitized before use in agriculture fields due to the presence of possible enteric pathogens. Composting of human faeces with food waste was evaluated as a possible method for this treatment. Temperatures were monitored in three 78-L wooden compost reactors fed with faeces-to-food waste substrates (F:FW) in wet weight ratios of 1:0, 3:1 and 1:1, which were observed for approximately 20 days. To achieve temperatures higher than 15 degrees C above ambient, insulation was required for the reactors. Use of 25-mm thick styrofoam insulation around the entire exterior of the compost reactors and turning of the compost twice a week resulted in sanitizing temperatures (>or=50 degrees C) to be maintained for 8 days in the F:FW=1:1 compost and for 4 days in the F:FW=3:1 compost. In these composts, a reduction of >3 log(10) for E. coli and >4 log(10) for Enterococcus spp. was achieved. The F:FW=1:0 compost, which did not maintain >or=50 degrees C for a sufficiently long period, was not sanitized, as the counts of E. coli and Enterococcus spp. increased between days 11 and 15. This research provides useful information on the design and operation of family-size compost units for the treatment of source-separated faeces and starchy food residues, most likely available amongst the less affluent rural/urban society in Uganda.     

Aging and compressibility of municipal solid wastes

The expansion of a municipal solid waste (MSW) landfill requires the ability to predict settlement behavior of the existing landfill. The practice of using a single compressibility value when performing a settlement analysis may lead to inaccurate predictions. This paper gives consideration to changes in the mechanical compressibility of MSW as a function of the fill age of MSW as well as the embedding depth of MSW. Borehole samples representative of various fill ages were obtained from five boreholes drilled to the bottom of the Qizhishan landfill in Suzhou, China. Thirty-one borehole samples were used to perform confined compression tests. Waste composition and volume-mass properties (i.e., unit weight, void ratio, and water content) were measured on all the samples. The test results showed that the compressible components of the MSW (i.e., organics, plastics, paper, wood and textiles) decreased with an increase in the fill age. The in situ void ratio of the MSW was shown to decrease with depth into the landfill. The compression index, Cc, was observed to decrease from 1.0 to 0.3 with depth into the landfill. Settlement analyses were performed on the existing landfill, demonstrating that the variation of MSW compressibility with fill age or depth should be taken into account in the settlement prediction.     

A method for ranking components importance in presence of epistemic uncertainties

Importance Measures (IMs) are used to rank the contributions of components or basic events to the system performance, e.g. its reliability or risk. Most times, IMs are calculated without due account of the uncertainties in the model of the behavior of the system. The objective of this work is to investigate how uncertainties can influence IMs and to develop a method for giving them due account in the corresponding ranking of the components or basic events. The uncertainties considered in this work affect the model parameters values and are assumed to be described by probability density functions. The method for ranking the contributors to the system performance measure is applied to the auxiliary feedwater system of a nuclear pressurized water reactor.     

The major accident risk (MAR) process - developing the profile of major accident risk for a large multi national oil company

The paper describes a programme to develop the profile of major accident risk across a large multi national oil company. It describes the concepts, tools and processes for constructing the risk profile and some of the key learnings from the exercise.     

Assessing coastal waters of American Samoa: territory-wide water quality data provide a critical “big-picture” view for this tropical archipelago

The coastal waters of American Samoa’s five high islands (Tutuila, Aunu’u, Ofu, Olosega, and Ta’u) were surveyed in 2004 using a probabilistic design. Water quality data were collected from the near-shore coastal habitat, defined as all near-shore coastal waters including embayments, extending out to 1/4 mile off-shore. Hydrography and water column samples were collected, and water quality data were compared to the Territorial water quality standards for pH, dissolved oxygen (DO), Enterococcus, chlorophyll a, water clarity, total nitrogen, and total phosphorus. All station measurements for pH, DO, and Enterococcus satisfied the local water quality standards, although some fraction of the Territory could not be assessed for either DO or Enterococcus. With respect to chlorophyll a, 66 ± 18% of Territory coastal waters complied with the standard, while 34 ± 18% failed to comply with the standard. For water clarity, 54 ± 18% of the Territorial waters complied with the standard while 42 ± 7% failed to comply. Territorial waters satisfied the standards for total nitrogen and phosphorus 72 ± 17% and 92 ± 10%, respectively. These data provide the first “big-picture” view of water quality in the near shore region around the high islands of American Samoa. While the picture is encouraging, these data suggest emerging water quality concerns.