Ethylene: An Urban Air Pollutant

Ethylene is an unusual air pollutant in that it is a plant hormone. Motor vehicle exhaust is a primary source. In the Washington, D. C, area, ethylene concentrations ranged from 700 ppb in the city center to 39 ppb in areas outside the circumferential beltway. Plants grown in these concentrations of ethylene, using controlled environment chambers, exhibited typical symptoms of ethylene toxicity: reduced growth, premature senescence, and reduced flowering and fruit production. When plants were grown in carbon-filtered ambient air, which was also filtered through KMnO₄ to remove ethylene by oxidation, growth, flowering, and fruit production increased. These observations demonstrate that ethylene air pollution is a continual source of stress for plant growth and development in an urban environment.     

Emissions into the Atmosphere Due to the Ceramic Salt Glazing Process

The techniques of Principal Component Analysis (PCA) and subsequent regression analysis were used in an attempt to describe local and upwind chemical and physical factors which affect the variability of SO₄ ^–2 concentrations observed in a rural area of the northeastern U.S. The data used in the analyses included upwind and local O₃ concentrations, temperature, relative humidity and other climatological information, SO₂, and meteorological information associated with backward trajectories. The investigation identified five principal components, three major (eigenvalues >1) and two minor (eigenvalues < one), which accounted for 52% (r = 0.72) of the variability in the SO₄ ^–2 regression model. These components can be described as representing local and upwind photochemistry, droplet growth, SO₂ emissions, and air mass characteristics. The study also indicated that in future studies it will be necessary to a priori select air pollution and meteorological variables for measurement to potentially increase the sensitivity of this type of receptor model.     

Comparison of Predicted and Measured Concentrations for 58 Alternative models of Plume Transport in Complex Terrain

The purpose of this study was to evaluate alternative prediction models for the SO₂ concentrations produced in the vicinity of the Ohio Edison Company Sammis Power Plant. The plant is situated in the northeastern portion of the Ohio River Valley in complex terrain. Comparisons of the 16 highest predicted and measured short-term SO₂ concentrations were conducted for a one year period for 58 alternative models. Several models were found to predict reasonably accurately the 16 highest measured 24-hour SO₂ concentrations. Each of these models requires an upward adjustment in the plume centerline location as the plume is transported downwind in rising terrain. These same models overpredict by substantial margins the 16 highest measured 3-hour SO₂ concentrations. Improvements in emissions inventory data and improvements in the prediction models used are believed necessary to increase prediction accuracy further.     

Application of a combined measurement and modeling method to quantify windblown dust emissions from the exposed playa at Mono Lake, California

Particulate matter < or =10 microm (PM10) emissions due to wind erosion can vary dramatically with changing surface conditions. Crust formation, mechanical disturbance, soil texture, moisture, and chemical content of the soil can affect the amount of dust emitted during a wind event. A refined method of quantifying windblown dust emissions was applied at Mono Lake, CA, to account for changing surface conditions. This method used a combination of real-time sand flux monitoring, ambient PM10 monitoring, and dispersion modeling to estimate dust emissions and their downwind impact. The method identified periods with high emissions and periods when the surface was stable (no sand flux), even though winds may have been high. A network of 25 Cox sand catchers (CSCs) was used to measure the mass of saltating particles to estimate sand flux rates across a 2-km2 area. Two electronic sensors (Sensits) were used to time-resolve the CSC sand mass to estimate hourly sand flux rates, and a perimeter tapered element oscillating microbalance (TEOM) monitor measured hourly PM10 concentrations. Hourly sand flux rates were related by dispersion modeling to hourly PM10 concentrations to back-calculate the ratio of vertical PM10 flux to horizontal sand flux (K-factors). Geometric mean K-factor values (K(f)) were found to change seasonally, ranging from 1.3 x 10(-5) to 5.1 x 10(-5) for sand flux measured at 15 cm above the surface (q15). Hourly PM10 emissions, F, were calculated by applying seasonal K-factors to sand flux measurements (F = K(f) x q15). The maximum hourly PM10 emission rate from the study area was 76 g/m2 x hr (10-m wind speed = 23.5 m/sec). Maximum daily PM10 emissions were estimated at 450 g/m2 x day, and annual emissions at 1095 g/m2 x yr. Hourly PM10 emissions were used by the U.S. Environmental Protection Agency (EPA) guideline AERMOD dispersion model to estimate downwind ambient impacts. Model predictions compared well with monitor concentrations, with hourly PM10 ranging from 16 to over 60,000 microg/m3 (slope = 0.89, R2 = 0.77).     

Rapid measurement of emissions from military aircraft turbine engines by downstream extractive sampling of aircraft on the ground: Results for C-130 and F-15 aircraft

Aircraft emissions affect air quality on scales from local to global. More than 20% of the jet fuel used in the U.S. is consumed by military aircraft, and emissions from this source are facing increasingly stringent environmental regulations, so improved methods for quickly and accurately determining emissions from existing and new engines are needed. This paper reports results of a study to advance the methods used for detailed characterization of military aircraft emissions, and provides emission factors for two aircraft: the F-15 fighter and the C-130 cargo plane. The measurements involved outdoor ground-level sampling downstream behind operational military aircraft. This permits rapid change-out of the aircraft so that engines can be tested quickly on operational aircraft. Measurements were made at throttle settings from idle to afterburner using a simple extractive probe in the dilute exhaust. Emission factors determined using this approach agree very well with those from the traditional method of extractive sampling at the exhaust exit. Emission factors are reported for CO₂, CO, NO, NO_x, and more than 60 hazardous and/or reactive organic gases. Particle size, mass and composition also were measured and are being reported separately. Comparison of the emissions of nine hazardous air pollutants from these two engines with emissions from nine other aircraft engines is discussed.     

Review of Russian-language studies on radionuclide behaviour in agricultural animals: part 4. Transfer to poultry

Data on radionuclide transfer to domestic chickens and ducks obtained from research performed in the former Soviet Union were reviewed to provide transfer coefficient values (Ff) to poultry and edible egg contents. The majority of the data are from experiments with ⁹⁰Sr and ¹³⁷Cs, reflecting the importance of these radionuclides after global fallout and major radiation accidents. Data for ³H, ⁵⁴Mn, ⁵⁹Fe, ⁶⁰Co, ²²Na ⁶⁵Zn, ¹³¹I and U are also given. The values derived have been compared with those in the current IAEA Handbook of parameter values for the prediction of radionuclide transfer in temperate environments (TRS 364) and the recent revision which incorporates the values from this paper. The Russian-language data give improved estimates for many radionuclides and the revised handbook is now based on the better quality data given for chronic administration.     

Review of Russian language studies on radionuclide behaviour in agricultural animals: 3. Transfer to muscle

Over 150 publications reporting studies conducted in the former USSR were reviewed to provide transfer coefficients (F_f) to the muscle of domestic animals from experiments using chronic administration, often for long timescales in large scale experiments. Only a few of these studies were made available in the English language literature or taken into account in international reviews. The values derived have been compared with expected values reported by the IAEA's Handbook of parameter values for the prediction of radionuclide transfer in temperate environments (TRS 364) where possible. The information presented here has been used in the current updating of parameters recommended for environmental assessments by the IAEA. Many of the reported values are for Sr due to the Mayak accident and Cs due to the Chernobyl accident. Nevertheless, the reported data for a wide range of radionuclides, in particular for Ru, Sb, and Zn markedly improve the extent of available data.