裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

基于RF-LSTM的鸡舍恶臭气体预测研究

以鸡舍氨气为研究对象,对鸡舍氨气预测模型进行了研究.首先,利用随机森林算法（RF）对影响鸡舍氨气浓度的环境变量进行重要性排序,选取温度、湿度、光照、气象温度、降雨量作为模型的输入变量;在此基础上,构建了基于长短时记忆神经网络（LSTM）的鸡舍氨气浓度预测模型,并将提出的预测模型应用于江苏省宜兴市某养鸡场的氨气浓度预测中,并与LSTM模型、RF-Elman模型和RF-BP模型进行了对比实验,结果表明,基于RF-LSTM模型的预测效果最好,其平均绝对误差（MAE）、平均绝对百分误差（MAPE）和均方根误差（RMSE）分别为0.9183、4.9637%和1.4262;同时,为了验证该模型的性能,本文还实现了不同时间尺度的鸡舍氨气浓度预测,提前2h、3h、4h、5h氨气预测的平均绝对误差（MAE）分别为1.6218、2.1991、2.8553和3.0677.本文提出的预测模型提高了鸡舍氨气浓度的预测精度,可为减少鸡舍恶臭气体排放提供科学依据.     

除Cd (Ⅱ)重金属吸附剂——巯基乙酰化玉米秸秆的制备

以玉米秸秆（CS）、巯基乙酸（TGA）为原料,通过化学反应制备出重金属吸附剂——巯基乙酰化玉米秸秆（MACS）,考察MACS对水样中Cd （Ⅱ）的去除性能,采用单因素实验法对MACS的制备条件进行优化研究。结果表明,MACS的优化制备条件为:CS粒径为0.20 mm （80目）,m（催化剂NHS）:m（EDC·HCl）为0.5:1,m（CS）:V（TGA）为1:5,反应介质pH值为5.0,反应温度25℃,反应时间2 h。在此条件下制备的MACS对水样中Cd （Ⅱ）的吸附效率可达到61.57%。红外分析表明,CS分子链中成功引入了巯基。     

污泥生物炭去除水中重金属的研究进展

重金属带来的环境风险日益严峻,利用污泥生物炭去除水中重金属污染方面的研究得到了广泛关注。结合当前国内外研究现状,归纳了不同条件下制备的污泥生物炭对水中重金属,如Cd、Pb、Cr、As等的吸附机理,污泥生物炭对大多数重金属的吸附满足物理吸附和化学吸附的多重作用,可通过增加生物炭表面有效基团及有效吸附位点提升吸附性能。同时,总结了影响吸附效率的各种因素,探究了污泥生物炭的再生问题,并对今后污泥生物炭去除水中重金属的研究方向做出了展望。     

Aerosol optical properties under different pollution levels in the Pearl River Delta (PRD) region of China

To clarify the aerosol hygroscopic growth and optical properties of the Pearl River Delta(PRD)region,integrated observations were conducted in Heshan City of Guangdong Province from October 19 to November 17,2014.The concentrations and chemical compositions of PM_(2.5),aerosol optical properties and meteorological parameters were measured.The mean value of PM_(2.5) increased from less than 35(excellent) to 35-75 μg/m~3(good) and then to greater than 75 μg/m~3(pollution),corresponding to mean PM_(2.5) values of 24.9,51.2,and 93.3 μg/m~3,respectively.The aerosol scattering hygroscopic growth factor(f(RH = 80%)) values were 2.0,2.12,and 2.18 for the excellent,good,and pollution levels,respectively.The atmospheric extinction coefficient(σext)and the absorption coefficient of aerosols(σ_(ap)) increased,and the single scattering albedo(SSA)decreased from the excellent to the pollution levels.For different air mass sources,under excellent and good levels,the land air mass from northern Heshan had lower f(RH) and σ_(sp) values.In addition,the mixed aerosol from the sea and coastal cities had lower f(RH) and showed that the local sources of coastal cities have higher scattering characteristics in pollution periods.     

建筑垃圾堆放点样本集构建与优化研究

为更好地解决手工制作的建筑垃圾堆放点样本集效率低、数据量少,难以支撑基于深度学习的遥感图像目标检测算法训练需求的问题,采用基于像素的遥感分类方法构建建筑垃圾堆放点样本集,在此基础上结合直方图均衡化,CS-LBP算子约束以及迁移学习的方法对Wasserstein生成对抗模型（WGAN）进行优化,实现了样本集扩充。研究结果表明:相对于纯手工制作的样本集,基于像素的遥感分类方法可以显著提升样本集制作的效率;同时,经过WGAN优化后,生成样本模拟了原始数据的颜色与纹理特征分布规律,增加了原始数据的多样性,满足了扩充样本集的需求。     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

电解锰渣基方沸石的制备及其对Pb2+的吸附性能

以电解锰渣为原料,经过"弱酸除杂-碱融活化-室温陈化-晶化"水热合成反应体系,在分别外加铝源和硅源的条件下制备方沸石ANA-A及ANA-S,运用XRF、XRD、SEM-EDS和BET等表征手段对2种方沸石的化学组成、晶相结构、微观形貌和比表面积进行分析。结果表明:在煅烧温度750℃、合成温度180℃、水热反应时间8 h的条件下,外加铝源和硅源均可合成方沸石。进一步研究2种沸石对水溶液中Pb2+的静态吸附性能,其所合成的电解锰渣基ANA-A及ANA-S方沸石均可以很好地用Langmuir等温模型拟合,属于单分子层吸附,饱和吸附量分别为161.29,185.19 mg/g,对初始浓度为100 mg/L的Pb2+去除率分别为93.69%和95.47%,且均符合Lagergren准二级动力学模型,属于化学吸附;两者中ANA-S的吸附效果更好。     

Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands(CWs).In this study,a coupled system comprising an integrated vertical flow CW(IVCW) and a microbial fuel cell(MFC) for swine wastewater tre atment was developed to research the effects of macrophytes commonly employed in CWs,Canna indica,Acorus calamus,and Ipomoea aquatica,on decontamination and electricity production in the system.Because of the different root types and amounts of oxygen released by the roots,the rates of chemical oxygen demand(COD) and ammonium nitrogen(NH_4~+-N) removal from the swine wastewater differed as well.In the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,the COD removal rates were 80.20%,88.07%,84.70%,and 82.20%,respectively,and the NH_4~+-N removal rates were 49.96%,75.02%,70.25%,and 68.47%,respectively.The decontamination capability of the Canna indica system was better than those of the other systems.The average output voltages were 520±42,715±20,660±27,and 752±26 mV for the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,respectively,and the maximum power densities were 0.2230,0.4136,0.3614,and0.4964 W/m~3,respectively.Ipomoea aquatica had the largest effect on bioelectricity generation promotion.In addition,electrochemically active bacteria,Geobacter and Desulfuromonas,were detected in the anodic biofilm by high-throughput sequencing analysis,and Comamonas(Proteobacteria),which is widely found in MFCs,was also detected in the anodic biofilm.These results confirmed the important role of plants in IVCW-MFCs.