铁碳促进O3/H2O2体系深度处理准好氧矿化垃圾床渗滤液尾水中难降解有机物

构建了铁碳-O_3/H_2O_2体系降解矿化垃圾床渗滤液尾水中有机物,并考察了体系O_3、铁碳及H_2O_2投加量、初始pH值和反应时间对铁碳-O_3/H_2O_2体系处理渗滤液尾水的影响.结果表明,在铁碳投加量为3 g·L~(-1),O_3投加量为9.798 mg·min~(-1),H_2O_2投加量为2 mL·L~(-1),初始pH值为3的条件下,反应10 min后,渗滤液尾水的COD和UV_(245)分别从711.96 mg·L~(-1)、0.19下降至295.04 mg·L~(-1)、0.10.类比实验结果表明,铁碳-O_3/H_2O_2体系对渗滤液尾水有机物具有较高的去除率,且可生化性得到提高(BOD/COD从0.04增加至0.40).紫外-可见和三维荧光光谱显示,废水中难降解有机物转化为小分子有机化合物且腐殖质的分子缩合度降低.最后,采用SEM-EDS、XRD和XPS技术对铁碳-O_3/H_2O_2体系的反应机理进行了解析,发现铁碳-O_3/H_2O_2反应的机理为铁碳微电解反应、铁氧化物-H_2O_2非均相芬顿反应、O_3/H_2O_2、铁碳-O_3非均相的高级氧化作用和铁基胶体对有机物的吸附沉淀作用.研究表明,铁碳-O_3/H_2O_2体系是一种能够有效去除矿化垃圾床渗滤液尾水中难降解有机物的方法.     

亚慢性氟暴露致小鼠海马损伤的影响及分子机制研究

为探明亚慢性氟中毒致小鼠海马损伤及分子机制,选用ICR雄性小鼠140只,随机分为对照(C)、低氟(LF)、高氟(HF)、低氟(LF)+L钙离子通道激动剂(FPL)、低氟(LF)+L钙离子通道抑制剂(NIF)、高氟(HF)+激动剂(FPL)、高氟(HF)+抑制剂(NIF) 7组,分别饮用自来水、5、30 mg·L~(-1)氟化钠水溶液90 d,氟染毒第84 d分别腹腔注射生理盐水、FPL64176、Nifedipine7d.同时,采用开场行为及水迷宫检测学习记忆能力;通过HE切片染色观察海马形态结构;根据试剂盒说明检测脑组织谷胱甘肽过氧化物酶(GSH-PX)、总超氧化物歧化酶(SOD)酶活性及丙二醛(MDA)含量;利用RT-PCR和Western Blot法分别检测海马内凋亡相关分子CaMKⅡ和Bax、Bcl-2基因/蛋白表达.结果发现,HF组、LF+FPL组和HF+FPL组小鼠毛发粗糙,暴躁不安.LF、HF组小鼠自发活动、探究行为及空间学习记忆力显著下降(p0.05),海马细胞损伤,SOD、GSH-PX活性极显著下降(p0.01),CaMKⅡ基因/蛋白表达水平显著(p0.05)或极显著(p0.01)上调,Bax基因/蛋白表达水平显著(p0.05)或极显著(p0.01)上调,Bcl-2基因/蛋白表达水平显著(p0.05)或极显著(p0.01)下调,Bax与Bcl-2基因/蛋白表达水平比值显著(p0.05)或极显著(p0.01)上调;LF+FPL、HF+FPL处理加剧了上述基因/蛋白表达水平,LF+NIF、HF+NIF组可逆转上述基因/蛋白表达水平.结果提示,氟中毒致脑损伤与L型钙离子通道及下游相关分子表达异常密切相关,而L钙离子通道抑制剂(Nifedipine)能改善氟暴露造成的海马损伤.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.     

Effects of Na+ on Cu/SAPO-34 for ammonia selective catalytic reduction

Copper-exchanged chabazite (Cu/CHA) catalysts have been found to be affected by alkali metal and alkaline earth ions. However, the effects of Na⁺ ions on Cu/SAPO-34 for ammonia selective catalytic reduction (NH₃-SCR) are still unclear. In order to investigate the mechanism, five samples with various Na contents were synthesized and characterized. It was observed that the introduced Na⁺ ion-exchanges with H⁺ and Cu^2 + of Cu/SAPO-34. The exchange of H⁺ is easier than that of isolated Cu^2 +. The exchanged Cu^2 + ions aggregate and form “CuAl₂O₄-like” species. The NH₃-SCR activity of Cu/SAPO-34 decreases with increasing Na content, and the loss of isolated Cu^2 + and acid sites is responsible for the activity loss.     

海水中阴极极化对X80钢应力腐蚀及氢脆敏感性的影响

目的研究不同p H值海水中阴极极化对X80管线钢应力腐蚀及氢脆的抑制作用。方法采用慢应变速率拉伸试验、电化学测试、微观组织观察等分析方法。结果 X80钢在天然海水中的析氢电位约为-940m V(vs.SCE,下同),海水p H为3.5时析氢电位发生正移。其应力腐蚀敏感性与极化电位有很大关系,随着极化电位负移,X80钢的氢脆敏感性增加。天然海水中当极化电位负于-950 m V时,断口出现准解理断裂特征形貌。在-1050 m V极化电位下,钢材进入氢脆断裂区发生脆性断裂。海水p H为3.5时,-900 m V钢材有发生氢脆的危险。结论与天然海水相比,X80钢在p H为3.5的酸性海水中具有较高的应力腐蚀敏感性,两种海水介质中X80钢的应力腐蚀敏感性均随极化电位负移而增加。     

7B04铝合金和30CrMnSiA钢短期腐蚀的电化学行为研究

目的研究7B04铝合金和30CrMnSiA合金钢试样的电化学性能。方法采用电化学实验、扫描电子显微镜(SEM)、腐蚀坑深度测试分别对7B04铝合金和30CrMnSiA合金钢试样在是否经过天然海水浸泡的情况下进行测试分析,得到微观腐蚀形貌和腐蚀坑深度以及试样表面不带锈和带锈时的电化学性能。结果随着Na Cl浓度增大,7B04铝合金和30CrMnSiA钢的自腐蚀电流变大,两者之间存在明显的电位差,接触后会发生电偶腐蚀。电偶电流与阴阳极面积比和Na Cl浓度有关,阴阳极面积比增大或Na Cl浓度升高均会导致电偶效应增强。经过海水短期浸泡后,7B04铝合金表面的锈层不仅没有起到抑制腐蚀的作用,反而使自腐蚀加重,但电偶效应确实有所减弱。结论沿海设备在使用过程中应竭力避免铝合金在锈层下工作。     

舰空导弹杀伤概率随机化检验方法

目的充分有效利用生产方风险,在既定的生产方风险和有限的试验样本条件下,合理分配舰空导弹杀伤概率假设检验中的双方风险。方法通过似然函数推导检验问题的最优势检验,设计一种随机化检验方法,在检验完成后且必要时进行一次Bernoulli试验,以确定是否接受原假设。结果计算结果显示,相对经典假设检验方法,随机化检验方法可以保证实际生产方风险不超过既定的生产方风险上限,同时可使军方风险更小。结论该方法能够合理利用生产方风险,在不增加试验样本的条件下,降低军方风险,具有很好的工程实践意义。     

铜合金实验室试验与实海挂片结果的比较与分析

目的比较实验室试验结果与实海挂片结果对B10和H62两种铜合金腐蚀性能评价的异同之处。方法采用线性极化、电化学阻抗、显微形貌观察等,比较两种铜合金在实验室模拟海水中的的腐蚀速率、点蚀倾向,结合反应机理、腐蚀形貌、环境等外部因素,分析导致实验室与实海环境下出现差异的原因。结果除榆林海域外,实海挂片与实验室结果都表明,B10试样的平均腐蚀速率小于H62。B10和H62两种铜合金随温度升高腐蚀速率增大,在实验室和实海情况下表现出一致性,且平均腐蚀速率都随浸泡时间的延长而降低。结论在实海环境中,温度不是影响点蚀的主要因素,微生物等其他环境因素会对点蚀产生较大影响。     

飞机用铝合金腐蚀行为和腐蚀预测研究现状及问题分析

针对不同的航空铝合金结构及部位,从腐蚀机理、腐蚀行为和腐蚀预测技术三方面较为系统地分析了研究现状及进展。在此基础上,明确了航空铝合金腐蚀预测技术需要进一步研究的问题,分别为飞机结构表面腐蚀环境的确定问题,材料在海洋大气环境下腐蚀电化学性能的准确测量问题,腐蚀预测模型的选取问题。