REGIONAL WATER QUALITY MANAGEMENT BY THE GENERALIZED REDUCED GRADIENT METHOD1

ABSTRACT: A river basin-wide water quality management system is considered. The river receives thermal as well as organic wastes. At-source treatment of these pollutants is imposed to control the basin-wide water quality. The related water quality standards are: the minimum DO concentration, the maximum allowable BOD concentration, the maximum allowable stream temperature, and the allowable rise in stream temperature. The general dynamic mathematical model representing water quality in streams and the thermal effects on BOD and DO concentrations is presented. The model is highly nonlinear in nature. The optimal management problem involving the model is solved by a recently developed nonlinear propgramming technique - the generalized reduced gradient (GRG) method. Comparison of results obtained by the GRG method vs. dynamic programming, and of results using a more realistic mathematical model vs. a simple model are presented. The analysis procedure can be applied to designing new and examining existing water quality programs, and to study the influence of alternate policies and constraints.     

A REVIEW ON DECISION MODELS IN ECONOMICS OF REGIONAL WATER QUALITY MANAGEMENT1

ABSTRACT The literature on decision models in economics of regional water quality management is reviewed and classified.     

One-at-a-time sensitivity analysis of pollutant loadings to subsurface properties for the assessment of soil and groundwater pollution potential

Chemical leak was numerically simulated for four chemical substances: benzene (light non-aqueous phase liquid (NAPL)), tetrachloroethylene (dense NAPL), phenol (soluble in water), and pentachlorophenol (white crystalline solid) in a hypothetical subsurface leak situation using a multiphase compositional transport model. One metric ton of chemical substances was assumed to leak at a point 3.51 m above the water table in a homogeneous unconfined aquifer which had the depth to water table of 7.135 m, the hydraulic gradient of 0.00097, the recharge rate of 0.7 mm/day, and the permeability of 2.92?×?10^?10 m². For comparison, surface spill scenarios, which had a long pathway from source to the water table, were simulated. Using the model results, point-source pollutant loadings to soil and groundwater were calculated by multiplying mass, impact area, and duration above and below the water table respectively. Their sensitivity to subsurface properties (depth to water table, recharge rate, porosity, organic carbon content, decay rate, hydraulic gradient, capillary pressure, relative permeability, permeability) was analyzed, with changing each parameter within acceptable ranges. The study result showed that the pollutant loading to groundwater was more sensitive to the subsurface properties than the pollutant loading to soil. Decay rate, groundwater depth, hydraulic gradient and porosity were influential to pollutant loadings. The impact of influential parameters on pollutant loadings was nonlinear. The dominant subsurface properties of pollution loadings (e.g., decay rate, groundwater depth, hydraulic gradient, and porosity for groundwater) also affect the vulnerability, and the subsurface pollutant loadings defined in this study are dependent on chemical properties as well, which indicates that the influential hydrogeological and physicochemical parameters to pollutant loadings can be used for pollution potential assessment. The contribution of this work is the suggestion that the sensitivity of pollutant loadings can be used for pollution potential assessment. Soil and groundwater pollution potential of chemicals are discussed altogether for leak scenarios. A physics-based model is used to understand the impact of subsurface properties on the fate and transport of chemicals above and below the water table, and consequently their impact on the pollutant loading to soil and groundwater.

     

Improved dissipation kinetic model to estimate permissible pre-harvest residue levels of pesticides in apples

Prediction of residual concentrations of applied pesticides during the pre-harvest period may be required to ensure the safety of agricultural products. In this study, time-dependent dissipation trends of carbaryl (CB), kresoxim-methyl (KM), flubendiamide (FB), flufenoxuron (FN), bitertanol (BT), and chlorantraniliprole (CN) applied to apples at recommended and threefold greater doses were modeled to estimate pre-harvest residue limit concentrations (C_PHRL) indicating permissible pesticide concentrations during the pre-harvest period. Double-exponential (DE) model results best fit the dissipation trends of all tested pesticides (correlation coefficients of 0.91–0.99) compared to zero-, first-, and second-order models. Among the pesticides examined, CB half-lives in apples of 2.9 and 6.6 days were the shortest, while those of FN (21.1–32.7 days) were the longest. The C_PHRL values for each pesticide in apples were estimated with DE model parameter values and could be used to determine harvest dates for safe apples with pesticide concentrations below their maximum residue limits. Application of the DE model for C_PHRL calculation provides more accurate information for farmers to produce agricultural products safe from pesticide residues.     

Bioaerosol: A Key Vessel between Environment and Health

Airborne transmission of infectious diseases has become a topic of intense debate since the outbreak of COVID-19.This special issue entitled"Bioaerosol,Environm...     

Modelling the long-term consequences of a hypothetical dispersal of radioactivity in an urban area including remediation alternatives

The Urban Remediation Working Group of the International Atomic Energy Agency's EMRAS (Environmental Modelling for Radiation Safety) program was organized to address issues of remediation assessment modelling for urban areas contaminated with dispersed radionuclides. The present paper describes the second of two modelling exercises. This exercise was based on a hypothetical dispersal of radioactivity in an urban area from a radiological dispersal device, with reference surface contamination at selected sites used as the primary input information. Modelling endpoints for the exercise included radionuclide concentrations and external dose rates at specified locations, contributions to the dose rates from individual surfaces, and annual and cumulative external doses to specified reference individuals. Model predictions were performed for a “no action” situation (with no remedial measures) and for selected countermeasures. The exercise provided an opportunity for comparison of three modelling approaches, as well as a comparison of the predicted effectiveness of various countermeasures in terms of their short-term and long-term effects on predicted doses to humans.     

Morphological and chemical composition characteristics of summertime atmospheric particles collected at Tokchok Island,Korea

Determination of the chemical compositions of atmospheric single particles in the Yellow Sea region is critical for evaluating the environmental impact caused by air pollutants emitted from mainland China and the Korean peninsula. After ambient aerosol particles were collected by the Dekati PM10 cascade impactor on July 17–23, 2007 at Tokchok Island (approximately 50 km west of the Korean coast nearby Seoul), Korea, overall 2000 particles (on stage 2 and 3 with cut-off diameters of 2.5–10 μm and 1.0–2.5 μm, respectively) in 10 samples were determined by using low-Z particle electron probe X-ray microanalysis. X-ray spectral and secondary electron image (SEI) data showed that soil-derived and sea-salt particles which had reacted or were mixed with SO₂ and NO_x (or their acidic products) outnumbered the primary and “genuine” ones (59.2% vs. 19.2% in the stage 2 fraction and 41.3% vs. 9.9% in the stage 3 fraction). Moreover, particles containing nitrate in the secondary soil-derived species greatly outnumbered those containing sulfate. Organic particles, mainly consisting of marine biogenic species, were more abundant in the stage 2 fraction than in the stage 3 fraction (11.6% vs. 5.1%). Their relative abundance was greater than the sum of carbon-rich, K-containing, Fe-containing, and fly ash particles, which exhibited low frequencies in all the samples. In addition, many droplets rich in C, N, O, and S were observed. They tended to be small, exhibiting a dark round shape on SEI, and generally included 8–20 at.% C, 0–12 at.% N, 60–80 at.% O, and 4–10 at.% S (sometimes with <3 at.% Mg and Na). They were attributed to be a mixture of carbonaceous matter, H₂SO₄, and NH₄HSO₄/(NH₄)₂SO₄, mostly from the reaction of atmospheric SO₂ with NH₃ under high relative humidity. The analysis of the relationship between the aerosol particle compositions and 72-h backward air-mass trajectories suggests that ambient aerosols at Tokchok Island are strongly affected not only by seawater from the Yellow Sea but also by anthropogenic pollutants emitted from China and the Seoul–Incheon metropolis, resulting in the dominance of complex secondary aerosol particles.     

Combustion characteristics of simulated gas fuel in a 30 kg/h scale pyrolysis-melting incinerator

Combustion characteristics of gas fuel in a pyrolysis-melting incinerator having a 30kg/h capacity were investigated. Pyrolyzed gas from waste was simulated by propane that was injected in the combustion chamber, and burnt through multi-staged combustion by distributing the combustion air to primary, secondary, and tertiary air nozzles. Temperatures and the concentrations of gas components in the combustion chamber were measured. Combustion performance was evaluated with respect to the temperature distribution and combustion gas concentrations of O(2), CO and NO(x). Using secondary air and/or tertiary air, the combustion performance was improved, and, in particular, NO(x) concentration decreased significantly following the tertiary air injection.     

Pretreatment of automobile shredder residue (ASR) for fuel utilization

Automobile shredder residue (ASR) was pretreated to improve its quality for fuel utilization. Composition analysis revealed that ASR components could be classified into four groups: (1) urethane and textile-light fraction and combustibles containing low levels of ash and Cl; (2) plastics and rubber-light or heavy fraction and combustibles containing high levels of Cl; (3) metals and electrical wire-heavy fraction and incombustibles, and (4) particles smaller than 5.6mm with high ash contents. Based on these results, we successively performed sieving to remove particles smaller than 5.6mm, float and sink separations to reject the heavy fraction and plastics and rubber containing Cl, thermal treatment under an inert atmosphere to remove Cl derived from PVC, and char washing to remove soluble chlorides. This series of pretreatments enabled the removal of 78% of the ash and 91% of the Cl from ASR. Sieving using a 5.6-mm mesh removed a considerable amount of ash. Product quality was markedly improved after the float and sink method. Specifically, the sink process using a 1.1 g cm(-3) medium fluid rejected almost all rubber containing Cl and a large amount of PVC. The remaining Cl in char, after heating at 300 degrees C under an inert atmosphere and washing, was considered to be present as insoluble chlorides that volatilized at temperatures above 300 degrees C. Based on a tradeoff relationship between product quality and treatment cost, ASR may be utilized as a form of refuse plastic fuel or char.