Airborne Particulate Emissions from a Chromic Acid Anodizing Process Tank

Particulate mass concentration, particle size distribution, and particle chemical composition measurements have been conducted on the gases exhausting from a chromic acid anodizing process tank. Particle mass concentrations in the 200 to 20,000 μg/m³ range were measured using open-faced filters (47 mm diameter) adjacent to the process tank liquid and with closed filters (90 mm diameter) in the exhaust duct. Particle size distributions, measured using University of Washington Mark 3 and Mark 20 Cascade Impactors, showed the particle aerodynamic mass median diameter was about 3 microns. Chemical analysis of the particle samples obtained by the Modified EPA Method 5 sampling train, the Mark 20 UW Cascade Impactors, and by the 47 mm and 90 mm diameter filters showed Cr⁺⁶ concentrations in the 20 to 1,500 μg/m³ range with over 99 percent of the chromium in particles larger than 1.0 microns diameter. An integrating nephelometer was used to measure the light scattering coefficient of the exhaust gases upstream of the wet scrubber. The light scattering coefficient increased by a factor of about 2–3 over the background level during the 40 minute time period while a part was being anodized. The bscat values ranged from 3 × 10^?5 to 3 × 10^?4 meters^?1 for the aerosol particles less than about 6 microns aerodynamic diameter.     

Nitrogen Compounds other than NO in Automobile Exhaust Gas

Recent studies of organic pyrolyses in the presence of nitric oxide have shown that various nitogen compounds, such as hydrogen cyanide (HCN) and aceto-nitrile (CH₃CN) are formed. This suggests the possibility that such compounds will be found in internal combustion processes, and may be present in automobile exhaust gases. The present paper describes some gas-chromatographic and wet analyses of exhaust gases. It is concluded that the amounts of hydrogen cyanide are less than 1 ppm, but that various organic nitrogen compounds may reach a level of about 100 ppm. The significance of these results is discussed.     

Performance and Cost Comparisons between Fabric Filters and Alternate Participate Control Techniques

A study was conducted to evaluate performance and cost comparisons of fabric filters and alternate fine particulate control techniques. In relating the removal of fine particulate to costs, due to the lack of fractional efficiency data, it was found necessary to treat a specific application in order to make the study manageable. The case chosen is that of the coal fired industrial boiler since Enviro-Systems has a pilot program in this application area.     

Desulfurization of Flue Gases in A Fluidized Bed of Modified Limestone

This publication concerns the dry removal of SO₂ from gases using limestone absorbents. It reports bench-scale experiments made with commercial samples of powdered limestone (CaCO₃) activated by addition of a cheap substance, namely CaCl₂. The absorption was carried out in a fluidized bed traversed by the flue gases, between 600° and 900° C. The degree and rate of transformation of CaCO₃ to CaSO₄ in the presence of SO₂ and air have been compared for unmodified and modified absorbents. Initial rates of reaction, and the variation of the rate of absorption with time have been measured. The influence of the SO₂ content of the gas has been assessed. At 700° C, the maximum degree of transformation of activated limestone to sulfate exceeds 90%, whereas untreated CaCO₃ transforms only to 16–20%. At the same temperature, more than 90% of SO₂ contained In a gas carrying 0.35% SO₂ is removed. Because of the much smaller quantity of solid absorbent required, dry absorption processes based on the modified absorbents might get renewed interest. The modified absorbents might also be used for in situ absorption in fluidized bed combustion, in which the temperatures are in the range studied in the present paper.     

Importance of incorporation of personal communication devices in evacuation simulators

The importance of the incorporation of personal communication devices in emergency evacuation simulators will be discussed. Four case studies are examined to identify usage statistics and human behavior when using the devices in an emergency. The case studies are: 9/11 World Trade Center Attacks, London train bombings, Virginia Tech shooting and United Flight #93. The case studies’ findings are implemented into the Vacate evacuation simulator, which uses particle swarm optimization to mimic human pedestrian behavior. The physical actions of using a device, as well as the reaction to the information transmitted during usage, are examined. Findings show that the effects of the personal communication devices can affect individuals that are close to the user of the device, as well as those not in the local vicinity of the user. These effects, combined with the rapid mainstream acceptance of communication technologies, justify the implementation of personal communication devices into evacuation simulators.     

Assessing safety culture in the Spanish nuclear industry through the use of working groups

This paper presents the design and the implementation of a methodology for measuring and improving safety culture at a nuclear power plant (NPP). The study has involved the completion of a pilot project aimed at seeing how to make use of the RADAR logic (Results, Approach, Deployment, Assessment and Review) of the EFQM model as a tool for the self assessment of safety culture in a nuclear power plant. The work was aimed at finding evidence of the safety culture that was in place at the plant and at identifying both the strengths of that culture and any areas in which it could be improved. The score obtained from an analysis of those strengths and areas for improvement has made it possible to prioritise the actions to be taken. The identification of perceptions and evidence, the agreement on the strong points and areas for improvement and the quantification of the safety culture have been performed by groups comprising volunteers who work at the NPP. The advantages of this methodology are assessed in the paper.     

Prediction of thermal hazards from fireballs

Various models of fireball diameter have been evaluated by statistical techniques. The model of Gayle for fireball diameter estimation showed good agreement between the predicted and experimental data. The models relating to fireball duration, transmissivity and view factor have been selected based on their relative merits. A user interactive computer program has been developed to predict thermal hazards from fireballs in chemical process industries.