Permits and effluent charges in the water pollution control policies of France,West Germany,and the Netherlands

In this article the water pollution control policies of these countries and their effects on emitters are analyzed. In the Netherlands, local water control boards levy pollution charges on both direct and indirect emitters. The charges are based upon measured emissions and actual treatment costs and they vary among the boards. Discharges into surface waters are by permission only. West German law sets nationally uniform rates only for direct emitters and some pollutants, irrespective of treatment costs. The States (Länder), however, may make indirect emitters liable to pay as well. In France, river basin agencies charge emitters and grant discounts where abatement facilities have been installed. Further policy instruments are tax cuts, subsidies, and standards set on local and national levels. France, in this complex policy, also uses contrats de branche where government and industries agree by contract on pollution abatement. Evidence shows that all these policies have reduced water pollution. As emissions decrease, problems of overcapacity might occur where collective water treatment plants have been installed already. Moreover, investment in additive abatement technology may inhibit the introduction of low-waste, integrated technologies. Yet the development of the latter, though expensive in the short run, should enable industry to meet more stringent standards in the future.     

The differential effect of organizational induction process on early work role adjustment

Early work role adjustment is hypothesized to be a function of previous work experiences, early organizational experiences, and personality differences. Formal collective induction into an organization was compared with informal individual induction. Induction mode was the dominant variable which predicted adjustment four months after employment. Formal collective induction contributed to higher job satisfaction and lower work/family conflict. The mode of induction did not affect team cohesion, role conflict, role ambiguity, or perceived worker influence in the workplace. Self-monitoring, a personality variable, contributed to the prediction of work/family conflict. Inducation mode did not interact with other independent variables in predicting job satisfaction or work/family conflict.     

Kinetic,equilibrium and thermodynamic studies for the sorption of metribuzin from aqueous solution using banana peels,an agro-based biomass

Banana peels were employed for the removal of metribuzin from aqueous solution. Sorption in the batch mode was optimized regarding pH, contact time, sorbent dose, initial pesticide concentrations, and temperature. The sorption data were fitted to pseudo-first-order, pseudo-second-order, intraparticle diffusion, Elovich, and liquid film diffusion model, the pseudo-second-order exhibiting best fit (R² = 0.9803). Of the four most common sorption isotherm models (Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich), the data followed the Langmuir isotherm with highest correlation. The maximum adsorption capacity was found to be 167 mg g^?1. Gibbs free energy, enthalpy, and entropy showed that the sorption was exothermic and spontaneous.     

Agent-based analysis and support for incident management

This paper presents an agent-based approach for error detection in incident management organizations. The approach consists of several parts. First, a formal approach for the specification and hierarchical verification of both traces and properties. Incomplete traces are enriched by enrichment rules. Furthermore, a classification mechanism is presented for the different properties in incident management that is based on psychological literature. Classification of errors provides insight in the functioning of the agents involved with respect to their roles. This insight enables the provision of dedicated training sessions and allows software support to give appropriate warning messages during incident management.     

Material hygiene: improving recycling of WEEE demonstrated on dishwashers

There must be a change in attitude towards end-of-life products. The view that these products pose a liability must be changed. Secondary material is valuable as raw material. Thus, activities encouraging changes in opinion are important.Two major EU directives guide the recycling process; the Directive of End-of-Life Vehicles (ELV) and the Directive of Waste Electrical and Electronic Equipment (WEEE). Both focus on the input of the recycling system, not on what is coming out of the system.The WEEE Directive is the legislation on the European level that governs the handling and processing of these types of products. The WEEE Directive is not only aimed at stricter handling and reduction of hazardous materials but also encourages EU member states to support technical development in order to facilitate increased recycling.In order to properly address these issues a mind-set, material hygiene, has been introduced. The basic idea is to act, in every life cycle phase of the product, towards highest possible efficiency in recycling. The outcome of useful material is in focus.A study on dishwashers is made with copper outcome as target. The results are based on Swedish conditions but general conclusions can be made. Limited design efforts can raise the outcome of valuable materials, if the recycling process is organized in an optimal manner.A theoretical concept of disassembly structures is used to draw general conclusions on the case study.Increasing product recycling suitability is one side of the problem; another is increasing effectiveness of handling and processing of end-of-life products.The purpose of this paper is to introduce the concept of “material hygiene” and based on that demonstrate a method for grading structural properties in a recycling perspective. The findings presented in this paper are based on a field study in which a number of dishwashers were disassembled and analyzed.