Electronic scraps--recovering of valuable materials from parallel wire cables

Every year, the number of discarded electro-electronic products is increasing. For this reason recycling is needed, to avoid wasting non-renewable natural resources. The objective of this work is to study the recycling of materials from parallel wire cable through unit operations of mineral processing. Parallel wire cables are basically composed of polymer and copper. The following unit operations were tested: grinding, size classification, dense medium separation, electrostatic separation, scrubbing, panning, and elutriation. It was observed that the operations used obtained copper and PVC concentrates with a low degree of cross contamination. It was concluded that total liberation of the materials was accomplished after grinding to less than 3 mm, using a cage mill. Separation using panning and elutriation presented the best results in terms of recovery and cross contamination.     

Leaching of metals from fly ashes in the presence of complexing agents

The leachability of some metals (Al, As, Ba, Ca, Cr, Cu, Fe, K, Mg, Mn, Ti, Zn) from fly ashes was studied in the presence of ethylenediamine tetraacetic acid (EDTA) and naturally occurring complexing agents-humic acids (HAs). Secondary complex-forming equilibria taking place in the leachates increase significantly the leached amounts of most metals. Kinetic experiments showed that almost the whole "available" amounts of metals are leached from fly ash within a time period of several hours (mostly within 20 h), with exceptions of matrix constituents (typically aluminium), which are released more slowly.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Environmental Impact Assessment of Polylactide(PLA)/Chicken Feathers Biocomposite Materials

The aim of this study is to analyse the environmental impacts (EIs) of the process of preparation of new biocomposite materials obtained from polylactide (PLA) and chicken feathers (CFs). Two CFs stabilization methods and different percentages of CFs have been studied. The EIs of these new composites were compared to the impact of virgin PLA. Cradle-to-gate life cycle inventories were assessed for 0–35% v/v of CFs in a CFs/PLA biocomposite. Two CFs stabilization processes, autoclave and surfactant, were tested and compared with the aim to prioritize one of them from the environmental point of view. A composite plate of 184?×?184?×?2.2 mm³ was defined as the functional unit. Autoclave stabilization process exhibited lower environmental impact compared with surfactant stabilization process mainly due to both the lower requirements of electricity and water and the reduced pollution loads of the generated wastewater. Thus, the autoclave process was selected as the standard method when comparing the EIs of the proposed CFs/PLA biocomposites. In this sense, the addition of CFs to PLA matrix proportionally reduces all the EIs compared to pure PLA due to the replacement of PLA with CFs. This behaviour can be explained because the PLA production accounts for the 99% of the impact of the biocomposite. Consequently, CFs conveniently stabilized might be an alternative raw material to prepare CFs/PLA biocomposites with less environmental impact compared to pure PLA.     

Interannual Changes in the C:N:P Ratios of Seston and Zooplankton of a High Mountain Lake in Sierra Nevada,Spain

We investigated the carbon, nitrogen and phosphorus content inthe seston and the zooplankton of a high-mountain lake duringthree years of contrasting physical and chemical conditions.Carbon in seston was ten times higher in 1995 than in 1996 and1997. Phosphorus content in seston was variable for the studyperiod, increasing gradually towards late summer in 1995, butpeaking abruptly in 1996 and 1997, reflecting atmosphericdepositions. Seston C:P were high and did not fit any definitepattern in 1995, and were particularly low after the thaw, increasing towards mid-summer in 1996 and 1997. As the seasonprogressed, major decreases in these ratios occurred coincidingwith important atmospheric inputs in the lake area. ZooplanktonN:P and C:P were negatively associated to the appearance ofrotifers and copepod nauplii in 1995, but positively correlatedto the ontogenetic development of the most abundant species,Mixodiaptomus laciniatus, in 1996. Seasonal variations inzooplankton N:P and C:P ratios showed limited interannual, butlarge intraannual variability. The comparison between the bulkcarbon in seston and zooplankton demands for this elementindicated that zooplankton were above food-quantity thresholdsfor maximum growth in 1995, 1996 and mid-season of 1997,therefore suffering only from food-quantity constraints afterthe thaw (nauplii dominance) and towards late season (adultdominance) in the latter year. The high C:P ratios in sestonrelative to zooplankton in 1995 imply that the zooplankton mayhave faced severe food-quality constraints (in terms ofphosphorus) during this year. Differences between bulkzooplankton and seston elemental nutrients are also discussed inrelation to the competitive abilities of species, andparticularly of Daphnia.     

Effect of Cross-Linking Waste Protein with Diepoxides on its Biodegradation under Anaerobic Conditions

Biodegradability testing was performed in an aqueous environment under anaerobic conditions after inoculation with digested sludge from municipal wastewater treatment plant. In cross-linking with 1,2:3,4-diepoxybutane in limits 0.8–9.1% weight, biodegradability degree decreased from 76.8 to 62.2%; when 1,2:7,8 diepoxyoctane in quantities 1.1–13.2% weight was used, biodegradability degree dropped more prominently – from 72.3 to 22.8%. There is obviously a direct connection between growing cross-link degree (assessed by so-called fixation index) and decreasing readiness to biodegradation, apparently owing to build-up of a network forming an obstacle to access of micro-organisms and enzymes.     

Sulfur Metabolism in Polluted Sphagnum Peat Bogs: A Combined 34S–35S–210Pb Study

The size and isotopic behavior of sulfur pools in²¹⁰Pb-dated peat cores were investigated to obtain aninsight into retention mechanisms of pollutant S in twomountain-top peatlands of the Northern Czech Republic, CentralEurope. The bogs were situated 40 km apart in an area whichbetween the years 1985 and 1995 received as much as 130 kg Sha^-1 yr^-1 from the atmosphere. Vertical peataccretion was faster at Pod Jelení horou (JH) than atVelký moál (VM). Organic carbon-bonded S was themost abundant sulfur pool, constituting 77 and 65 wt. % at JHand VM, respectively. At JH both the S concentration maximumand the highest annual S deposition rate were displaceddownward by more than 20 years (from 1987 to the 1960s)indicating that the buried S is vertically mobile. At VM the Sconcentration was the highest in the topmost 2-cm section eventhough atmospheric S deposition peaked in 1987. Differentmechanisms of S isotope redistribution prevailed in thetopmost peat layers at JH, where a negative ³⁴Sshift occurred, and at VM, where a positive ³⁴Sshift occurred. Bacterial sulfate reduction was responsiblefor the negative ³⁴S shift at JH. One possibleexplanation of the positive ³⁴S shift at VM isrelease of ³²S-enriched products of mineralization duringpeat diagenesis. There was a strong positive correlationbetween the abundance of total and pyrite S along the profiles.The presence of pyrite S at VM (526 ± 60 ppm) suggestedthat even at VM bacterial sulfate reduction occurred. Ananaerobic incubation of JH peat indicated sulfate reductionrate of 600 nmol g^-1 day^-1. The turnover times forinorganic S pools were shorter than for the organic S pools.Cumulative S contents in the Czech peat bogs were found to besignificantly lower than in similar sites in the NortheasternU.S., even though the atmospheric S inputs were more thanthree times higher at the Czech sites. Possible causes of suchdiscrepancy are discussed.     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.     

Methodology for quantification of waste generated in Spanish railway construction works

In the last years, the European Union (EU) has been focused on the reduction of construction and demolition (C&D) waste. Specifically, in 2006, Spain generated roughly 47million tons of C&D waste, of which only 13.6% was recycled. This situation has lead to the drawing up of many regulations on C&D waste during the past years forcing EU countries to include new measures for waste prevention and recycling. Among these measures, the mandatory obligation to quantify the C&D waste expected to be originated during a construction project is mandated. However, limited data is available on civil engineering projects. Therefore, the aim of this research study is to improve C&D waste management in railway projects, by developing a model for C&D waste quantification. For this purpose, we develop two equations which estimate in advance the amount, both in weight and volume, of the C&D waste likely to be generated in railway construction projects, including the category of C&D waste generated for the entire project.     

Physical Properties, Photo- and Bio-degradation of Baked Foams Based on Cassava Starch, Sugarcane Bagasse Fibers and Montmorillonite

The objectives of this work were to develop biodegradable trays from cassava starch, sugarcane fibers and Na-montmorillonite (Na-MMT) using a baking process and to study the effects of these components on the physical properties, photo- and bio-degradation of the trays. The sample F20 (produced with 20 g fiber/100 g formulation) showed the maximum yield production (100 %). All formulations resulted in well-shaped trays with densities between 0.1941 and 0.2966 g/cm³. The addition of fibers and Na-MMT resulted in less dense and less rigid trays compared to control samples (only starch). The studied processing conditions resulted in good nanoclay dispersion, leading to the formation of an exfoliated structure. The evaluation of the photo-degradation stability of the trays under UV exposure for 336 h showed that a sample produced with a specific combination of fiber and nanoclay (20 g fiber and 5 g nanoclay/100 g formulation) had the highest loss in stress at break (91 %). Biodegradation assays showed that Control trays (starch) and F20 (20 g fiber/100 g formulation) lost a greater percentage of their weight after 90 days of incubation in soil, with losses of up to 85.50 and 82.70 %, respectively.