Numerical study of heat transfer characteristics of char from waste tire pyrolysis

To investigate heat transfer of char from waste tire pyrolysis, the cooling of char was simulated by the computational fluid dynamics. To scrutinize the heat transfer characteristics, bed height, temperature of cooling wall, and mixing time were selected as calculation parameters. From the results, increasing the char bed height from 0.005 to 0.02 m, the total heat transfer is decreased as from 45.5 to 26.5 J. As the char bed height is further increased from 0.02 to 0.06 m, the total heat transfer is decreased from 26.5 to 9.1 J. The char bed height affects the total heat transfer significantly. The total heat transfer decreases from 15.9 to 14.0 J as the temperature of cooling wall increases from 273.15 to 323.15 K. The total heat transfer mildly depends on the temperature of cooling wall. The particle mixing time increases from 10 to 120 s and the total heat transfer decreases from 28.6 to 22.6 J. It is noted that the particle contact is enhanced between char particles as well as the particles and cooling wall as the particle mixing time decreases. Consequently, heat transfer is augmented.     

Recycling of biodiesel fuel wastewater for use as a liquid fertilizer for hydroponics

Wastewater is discharged during washing processes in the production of biodiesel fuel (BDF) using alkaline catalysts. It can be recycled as a liquid fertilizer for hydroponics by adding essential components for plant growth. The effects of the liquid fertilizer on plant growth were investigated. Liquid fertilizer containing a smaller amount of the BDF wastewater had a similar effect on plant growth as the standard nutrient solutions. This result reveals that BDF wastewater can be recycled for use as a liquid fertilizer for hydroponics. However, fertilizer with a larger amount of the BDF wastewater showed poor and varied plant growth due to the growth of microorganisms in the contaminated wastewater. Hence, when BDF wastewater becomes contaminated during storage, sterilization is necessary to recycle it as a liquid fertilizer. Moreover, contamination during storage should be avoided for successful recycling.     

Spatial simulation and LCA evaluation on the plastic waste recycling system in Tianjin

With the rapid economic development in China, the amount of plastic waste (PW) generated has greatly increased and much of the waste is currently not treated. To reduce greenhouse gas (GHG) emissions from recycling of PW, we estimated the PW flow and considered methods to improve the household PW recycling system in Tianjin by adjusting processes during transportation and establishing a PW recycling factory in Zi’ya Industrial Park. The goal of the study was to identify reasonable improvements for the recycling system and clarify the environmental load. Geographic information system (GIS) technology was used to simulate transport processes for comparing GHG emissions from the transport processes between the present case and an improved case. Life cycle assessment (LCA) was used to compare GHG emissions between a projected scenario and a baseline scenario. Estimated GHG emissions during transport processes in the improved case were reduced by about 12,197 t CO₂ eq per year compared to the present case, equivalent to about 65.9 % of the total emissions in the present case. GHG emissions in the projected scenario were about 101,738 t CO₂ eq less per year than the baseline scenario, equivalent to about 75.5 % of the total emissions in the baseline scenario.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

Reduction of hazardous elements contained in sewage sludge incineration ash

Research and experimental studies were carried out in relation to reduction of hazardous elements contained in sewage sludge incineration ash. A questionnaire survey was conducted in 69 Japanese municipalities with sewage sludge incineration facilities. Selenium content in bag filter ash and ceramic filter ash was relatively higher than that in ash of cyclone and electrostatic precipitators. It was assumed that selenium vaporized in the furnace was due to adsorb in the fly ash on filter when passing through the low-temperature filter. To reduce high boiling point heavy metals in the ash, sewage sludge and incineration ash were heated up using a small muffle furnace. As the result, the chrome and nickel contents were reduced. A decrease in the surface area of ash and the reduction of elements occurred at the same time in sewage sludge and incineration ashes tested in this study.     

The effects of using reprocessable material on the durability and mechanical properties of landfill leachate collection HDPE pipes

This paper investigated the durability and mechanical properties of landfill leachate collection HDPE pipes which had been made of different weight percent amounts of virgin and reprocessable HDPE compounds (VC and RC). Durability is reported base on the chemical properties, obtained through oxidative induction time (OIT) and melt flow index (MFI) measurements, at the temperature of 50 °C and over a period of 12 months immersion in a synthetic leachate. Mechanical properties are also described according to tensile and pressure tests which had been conducted on the pipes samples. All of the factors were examined had been affected by the addition of RC, but for the special combination the antioxidant depletion was significantly affected by the experimental aging condition and no important changes had been observed in the other pipe properties. The results from OIT tests indicate that the rate of antioxidant depletion is reduced by an increase in the weight percent amounts of RC, during the experimental aging condition. This reduction is probably attributed to the extraction of antioxidants from RC in their recovery process. Finally, although these results are related to the particular HDPE compound, antioxidant formulation and condition examined, but it can be said that the use of clean own reprocessable material for the production of landfill leachate pipes shall be permitted without limitations.     

A comparison of refrigerant management policies and suggestions for improvement in South Korea

HFCs (hydrofluorocarbons) emerged as alternative refrigerants after the production of chlorofluorocarbons was banned and hydrochlorofluorocarbons were phased out, under the Montreal Protocol on Substances that Deplete the Ozone Layer. However, because the Kyoto Protocol considered HFCs as greenhouse gases, and their impact on climate change has been increasing, major developed countries have been strengthening existing regulations on the use of HFCs as refrigerants. South Korea has also passed various legislations related to refrigerant management. However, reports indicate that implementation of these regulations has been ineffective, due to the absence of a specific system for managing the production, use, and disposal phases of refrigerants. To identify and resolve these issues, this study investigates the current state of refrigerant management in South Korea for those three phases. Refrigerant management policies are compared between different legislatures, using the examples of the European Union, United States, and Japan. Based on the findings, five types of measures are suggested to reduce the production and consumption of refrigerants, and to improve refrigerant management regulations in ways that are most appropriate to the South Korean context.     

Preparation of biochar catalyst with saccharide and lignocellulose residues of corncob degradation for corncob hydrolysis into furfural

This paper presented a novel process for production of furfural by hydrothermal degradation of corncob over biochar catalyst, in which it was prepared with the recycling degradation solution and lignocellulosic solid residues. The biochar catalyst was papered by lignocellulose residues and concentrated saccharide solution, and then impregnated in 0.5 mol/L sulphuric acid at room temperature for 24 h assisted by the ultrasonic vibration. In the system of recycling, 8.8 % lignocellulose residues and 100 % concentrated saccharide solution from corncob hydrolysis have been recycled. Hydrolysis of corncob was carried out at 180 °C for duration of 170 min over the biochar catalyst. The experimental results have shown that the furfural yield of up to 37.75 % and overall corncob conversion rate of 62.00 % could be achieved under optimum operating conditions for the catalysts preparation and the corncob hydrolysis. It is believed that the acid density of 4.27 mmol/g of biochar catalyst makes the SO₃H groups cleave β-1,4 glycosidic linkages effectively and hydrolyze the cellulose and hemicellulose to water-soluble sugars, as well as to facilitate dehydration of xylose to give the product of furfural.     

Films Made by Blending Poly(ε-Caprolactone) with Starch and Flour from Sagu Rhizome Grown at the Venezuelan Amazons

Starch-based composite films have been proposed as food packaging. In this context, the study of non-conventional starch sources (sagu, Canna edulis Kerr) has worldwide special attention, because these materials can impart different properties as carbohydrate polymers. A thorough study of the matrices used (sagu starch and flour) was carried out. In the same way, thermoplastic starch (TPS)/PCL blend and thermoplastic flour (TFS)/PCL blend were obtained by melt mixing followed by compression moulding containing glycerol as plasticizer. In this study, chemical composition of the matrices and their properties were related with the properties of the developed films. Moisture content, water solubility, X-ray diffraction, thermogravimetric analysis and mechanical and microstructural properties were evaluated in the films. Taking into account the results, the sagu flour has great potential as starchy source for food packaging applications. However, concretely the flour had lower compatibility with the PCL compared to the starch/PCL blend.