NOx emission calculations for bulk carriers by using engine power probabilities as weighting factors

An important marine pollution issue identified by the International Maritime Organization (IMO) is NO_x emissions; however, the stipulated method for determining the NO_x certification value does not reflect the actual high emission factors of slow-speed two-stroke diesel engines over long-term slow steaming. In this study, an accurate method is presented for calculating the NO_x emission factors and total amount of NO_x emissions by using the actual power probabilities of the diesel engines in four types of bulk carriers. The proposed method is suitable for all types and purposes of diesel engines, is not restricted to any operating modes, and is highly accurate. Moreover, it is recommended that the IMO-stipulated certification value calculation method be modified accordingly to genuinely reduce the amount of NO_x emissions. The successful achievement of this level of reduction will help improve the air quality, especially in coastal and port areas, and the health of local residents.

Implications: As per the IMO, the NO_x emission certification value of marine diesel engines having a rated power over 130 kW must be obtained using specified weighting factor (WF)-based calculation. However, this calculation fails to represent the current actual situation. Effective emission reductions of 6.91% (at sea) and 31.9% (in ports) were achieved using a mathematical model of power probability functions. Thus, we strongly recommend amending the certification value of NO_x Technical Code 2008 (NTC 2008) by removing the WF constraints, such that the NO_x emissions of diesel engines is lower than the Tier-limits at any load level to obtain genuine NO_x emission reductions.     

Nationwide monitoring of atmospheric PCDD/Fs and dioxin-like PCBs in South Korea

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) were measured in ambient air samples collected from different parts of South Korea in 2008, and the measured levels were used for assessing the spatial and temporal distribution of atmospheric PCDDFs and DL-PCBs in South Korea. The average concentrations of atmospheric PCDD/Fs and DL-PCBs among the 37 sites were 28 fg I-TEQ m⁻³ (ND ∼ 617) and 1 fg WHO-TEQ m⁻³ (ND ∼ 0.016). Elevated atmospheric levels of PCDD/Fs and DL-PCBs observed at residential/industrial sites and in the north-west of Korea, indicated a potential contribution and impacts of anthropogenic sources of PCDD/Fs and DL-PCBs. These levels were similar or lower than those previously reported in other ambient air surveys. Average concentrations of PCDD/Fs showed small seasonal variations (ANOVA analysis, p = 0.144). The highest concentrations of PCDD/Fs were observed during winter, followed by spring, autumn and summer. Atmospheric PCDD/Fs and DL-PCBs in South Korea rapidly decreased during the last 10 years (1998-2008), demonstrating the efficiency of stricter regulations and the application of best available technologies/best environmental practices at emission sources. Comparison of the congener profiles and principal component analysis showed that current atmospheric PCDD/Fs are mostly influenced by industrial sources and PCBs from old commercial PCB uses. Nationwide POPs monitoring will continue and allows an effective evaluation of the implementation of the Stockholm Convention on POPs.     

Evaluation of food waste disposal options by LCC analysis from the perspective of global warming: Jungnang case, South Korea

The costs associated with eight food waste disposal options, dry feeding, wet feeding, composting, anaerobic digestion, co-digestion with sewage sludge, food waste disposer, incineration, and landfilling, were evaluated in the perspective of global warming and energy and/or resource recovery. An expanded system boundary was employed to compare by-products. Life cycle cost was analyzed through the entire disposal process, which included discharge, separate collection, transportation, treatment, and final disposal stages, all of which were included in the system boundary. Costs and benefits were estimated by an avoided impact. Environmental benefits of each system per 1 tonne of food waste management were estimated using carbon prices resulting from CO(2) reduction by avoided impact, as well as the prices of by-products such as animal feed, compost, and electricity. We found that the cost of landfilling was the lowest, followed by co-digestion. The benefits of wet feeding systems were the highest and landfilling the lowest.     

Numerical simulation of an array of fences in Saemangeum reclaimed land

This paper discusses about the quantitative effect of windbreak fences on wind velocity in the reclaimed land at Saemangeum in South Korea. Windbreak fences were constructed in the reclaimed land to reduce the wind velocity to prevent the generation and diffusion of dust. However, up to this time, no in-depth studies were conducted to quantitatively measure the effect of the windbreak fences on wind velocity thus an optimum windbreak structure is not yet determined. Using CFD simulations, the effects of fence porosity, fence height, and the distance between the adjacent fences were investigated. A wind tunnel experiment was initially conducted and data gathered were used to develop the CFD models. From the experiments and CFD simulations, the overall percentage difference of the measured velocities was 7.20% which is generally acceptable to establishing the reliability of the CFD models. The reduction effect on wind velocity was measured in between the adjacent fences up to a height of 0.6 m from the ground surface. In terms of porosity ( = 0, 0.2, 0.4, 0.6), 0.2 was found to be the optimum value. Conversely, the effect of fence height (0.6, 0.8 and 1.0 m) showed no significant difference; therefore, 0.6 m height is recommended. In addition, the reduction effect of distance between the adjacent fences (2, 4 and 6 m) on wind velocity having a 0.2 porosity has decreased to about 75% regardless of the distance. In the case of the reclaimed land in Saemangeum, a decrease of 75% can prevent the generation and diffusion of dusts. However, the source of dusts is very large. Therefore, constructing an array of windbreak with 6 m distance between them is deemed necessary.     

Arsenic concentration in porewater of an alkaline coal ash disposal site: Roles of siderite precipitation/dissolution and soil cover

The geochemical behavior of As in porewaters of an alkaline coal ash disposal site was investigated using multilevel samplers. The disposal site was in operation from 1983 until 1994 and was covered with 0.3–0.5 m thick soils in 2001 when this study was initiated. Sequential extraction analyses and batch leaching experiments were also performed using the coal ash samples collected from the disposal site. The results suggest the important roles of siderite (FeCO₃) precipitation/dissolution and soil cover, which have been ignored previously. Arsenic levels in the porewater were very low (average of 10 μg L⁻¹) when the site was covered with soil due to coprecipitation with siderite. The soil cover enabled the creation of anoxic conditions, which raised the Fe concentration by the reductive dissolution of Fe-(hydr)oxides. Because of the high alkalinity generated from the alkaline coal ash, even a small increase in the Fe concentration (0.66 mg L⁻¹ on average) could cause siderite precipitation. When the soil cover was removed, however, an oxidizing condition was created and triggered the precipitation of dissolved Fe as (hydr)oxides. As a result, the dissolution of previously precipitated As-rich siderite caused higher As concentration in the porewater (average of 345 μg L⁻¹).     

Effects of time-gap settings of adaptive cruise control (ACC) on driving performance and subjective acceptance in a bus driving simulator

A study was conducted to investigate the effects of time-gap settings and contents of secondary tasks on a fix-based bus driving simulator on drivers’ performance while reclaiming control from ACC in a car-following scenario of emergency brake by the lead vehicle. Thirty professional bus drivers drove on the simulator with the scenario of highway traffic flow under 12 random time-gap settings: from 0.64 s to 2.40 s with the interval of 0.16 s. As for the effects of secondary tasks, subjects were evenly divided into three conditions: no secondary task interference, simple secondary task, and complex task. The results demonstrated that different safety demarcations of time-gaps on subjective acceptance and driving performance can be found out. The integrated demarcations separated time-gaps into divisions that represented different levels of danger. It revealed that the safer time-gaps for different situations were: longer than 1.60 s for none-secondary task distraction and longer than 2.08 s for being continuously distracted by secondary tasks. The demand for simple tasks is relatively high, so a larger time-gap is needed for the driver to remain safe. This research has implications for the time-gap selection of ACC and effects of secondary task distraction on buses. A next logical step will focus on determining time-gaps for lead vehicles on curves or slopes, when multiple vehicles are present ahead, and modeling driver behavior and performance with ACC for cars, buses, and other types of vehicles.     

Effect of metal and glycol on mechanochemical dechlorination of polychlorinated biphenyls (PCBs)

This paper assesses the potential of mechanochemical method with fine metal powder, glycol and alkali for polychlorinated biphenyls (PCBs) removal from waste insulating oil. The effects of relevant parameters, such as kinds of chemicals, rate and time of milling were examined. After each run, the total PCBs content in waste insulating oil was measured. Polyethylene glycol 200, long chain-glycol was more effective than triethylene glycol and ethylene glycol, short chain-glycol as hydrogen donor in mechanochemical dechlorination of PCBs. A maximum of 99.9% PCBs removal (below 2ppm) and 94% total chlorine removal were achieved with the mechanochemical process for 2h.     

Characterization of the monthly variation in (1 → 3)-β-d-glucan concentrations in university laboratories

We characterize the monthly variation in (1 → 3)-β-d-glucan concentration measured over the course of 1 year, and we evaluate the characteristics of size selection using a two-stage cyclone sampler. The (1 → 3)-β-d-glucan concentrations were measured in four bio-related laboratories. A total of 156 samples were collected using a new two-stage cyclone sampler. Analysis of (1 → 3)-β-d-glucan was performed using the kinetic Limulus amebocyte lysate assay. The study showed that airborne (1 → 3)-β-d-glucan concentrations were significantly higher in laboratory D (mean ± SD 1,105?±?1,893 pg/m³) and in the spring (5,458 pg/m³). The highest concentration of (1 → 3)-β-d-glucan occurred in the spring, particularly in May.     

Photocatalytic bacterial inactivation by polyoxometalates

The photocatalytic inactivation (PCI) of Escherichia coli (Gram-negative) and Bacillus subtilis (Gram-positive) was performed using polyoxometalate (POM) as a homogeneous photocatalyst and compared with that of heterogeneous TiO₂ photocatalyst. Aqueous suspensions of the microorganisms (10⁷–10⁸ cfu ml⁻¹) and POM (or TiO₂) were irradiated with black light lamps. The POM-PCI was faster than (or comparable to) TiO₂-PCI under the experimental conditions employed in this study. The relative efficiency of POM-PCI was species-dependent. Among three POMs (H₃PW₁₂O₄₀, H₃PMo₁₂O₄₀, and H₄SiW₁₂O₄₀) tested in this study, the inactivation of E. coli was fastest with H₄SiW₁₂O₄₀ while that of B. subtilis was the most efficient with H₃PW₁₂O₄₀. Although the biocidal action of TiO₂ photocatalyst has been commonly ascribed to the role of photogenerated reactive oxygen species such as hydroxyl radicals and superoxides, the cell death mechanism with POM seems to be different from TiO₂-PCI. While TiO₂ caused the cell membrane disruption, POM did not induce the cell lysis. When methanol was added to the POM solution, not only the PCI of E. coli was enhanced (contrary to the case of TiO₂-PCI) but also the dark inactivation was observed. This was ascribed to the in situ production of formaldehyde from the oxidation of methanol. The interesting biocidal property of POM photocatalyst might be utilized as a potential disinfectant technology.