催化湿式氧化法处理吡虫啉农药废水

自制了Cu／Mn，Cu／Ce，Cu／Ni，Ce／Mn，Ce／Ag等催化剂，经过性能比较，选择催化活性较高且金属溶出量较小的Cu／Ni作催化剂。用催化湿式氧化法处理吡虫啉农药废水，考察了各种因素对处理效果的影响。实验结果表明：在进水pH为6．93、Cu／Ni加入量为4．0g、反应温度为190oC、氧分压为1．6MPa、反应时间为120min的条件下，COD去除率为95％；处理后废水的BOD5／COD从0．093增至0．590，可生化性明显改善。     

有机离子载入-复焙烧失法制备新型净水材料

探索了一种制备介孔复合净水材料的新方法——载入有机离子一复焙烧失法。通过实验得到的最佳工艺参数为：有机载入剂为CTMAB,有机载入剂(质量浓度5g/L)加入量4mL／g,有机离子交换反应时间2h,反应温度40℃,复焙烧失温度230℃,复焙烧失时间1．5h。在最佳工艺条件下制备的净水材料对色度为7400倍、COD为3040mg／L的染料废水的脱色率为98．9％,略优于杏壳活性炭的脱色率(98．2％);COD去除率为91．3％,与杏壳活性炭的COD去除率91．7％相差无几。净水材料的染料吸附量是添加剂升温烧蚀后产品的近85倍,是酸洗刻蚀后产品的近590倍,是原材料的900多倍,其对染料废水的净化能力整体优于杏壳活性炭。     

镉试剂2B固相萃取光度法测定水中微量银

研究了镉试剂2B固相萃取测定银的方法。在pH为9.5的硼砂-氢氧化钠缓冲介质中,乳化剂-OP存在下,镉试剂2B与银反应生成2∶1稳定络合物,该络合物可用pH使用范围为1~12的W atersX terraTMRP18固相萃取小柱富集,小柱上富集的络合物用乙醇(内含0.01 mol/L、pH为9.5的四氢吡咯-醋酸缓冲溶液)洗脱后用光度法测定,在洗脱剂介质中最大吸收波长为555 nm,摩尔吸光系数为1.04×105L/(mol.cm)。银质量浓度在0.01~1.0μg/mL内符合比尔定律,方法用于环境水样中银含量的测定,结果令人满意。     

BaO/γ-Al2O3同时吸附脱除一氧化氮和二氧化硫

利用固定床连续流动反应器研究了BaO／γ—Al2O，同时吸附模拟烟气中NO和SO2的工艺条件和再生循环使用性能，对BaO／γ—Al2O3进行了比表面积和程序升温表面反应（TPSR）等表征分析。结果表明，BaO／γ—Al2O3的适宜工艺条件是SO2与NO体积比为2．9～8．4、原料气中O2体积分数大于4．5％、吸附温度448～523K。BaO／γ—Al2O3在循环使用过程中吸附能力下降。与NOXSO吸附催化剂Na2CO3／γ—Al2O3相比，BaO／γ-Al2O3同时吸附SO2和NO的能力大、再生循环使用性能好、适宜的SO2与NO体积比范围宽、热稳定性好。将BaO／γ—Al2O3应用于NOXSO工艺可望提高该工艺的脱硫、脱氮效率。     

Effects of Preparation Parameters on Properties of Soy Protein-Based Fiberboard

The effects of manufacturing parameters on mechanical properties of medium density fibreboard (MDF) bonded with modified soy protein-based glue were studied to find an appropriate manufacture technology. Physical properties of MDF made with different amount of wax emulsion were measured. Results indicated that water repellent had no obvious influence on physical properties of soy protein-based MDF boards. The fiberboards bonded with soy protein-based glue showed stronger water resistance properties than those bonded with urea–formaldehyde (UF) resins. Furthermore, the soy protein-based MDF boards had good quality [25.2% 24 h soak thickness swell (TS), 29.9 MPa modulus of rupture (MOR), 3130 MPa modulus of elasticity (MOE)], which met requirements of Chinese national standard. Practical processing parameters were obtained by orthogonal experiment, i.e., glue content 8.0%, hot-press temperature 200 °C, and hot-press time 150 s.     

Effects of Alkali Treatment on the Properties of Short Flax Fiber–Poly(Lactic Acid) Eco-Composites

In this study, the influence of alkali (NaOH) treatment on the mechanical, thermal and morphological properties of eco-composites of short flax fiber/poly(lactic acid) (PLA) was investigated. SEM analysis conducted on alkali treated flax fibers showed that the packed structure of the fibrils was deformed by the removal non-cellulosic materials. The fibrils were separated from each other and the surface roughness of the alkali treated flax fibers was improved. The mechanical tests indicated that the modulus of the untreated fiber/PLA composites was higher than that of PLA; on the other hand the modulus of alkali treated flax fiber/PLA was lower than PLA. Thermal properties of the PLA in the treated flax fiber composites were also affected. T_g values of treated flax fiber composites were lowered by nearly 10 °C for 10% NaOH treatment and 15 °C for 30% NaOH treatment. A bimodal melting behavior was observed for treated fiber composites different than both of neat PLA and untreated fiber composites. Furthermore, wide angle X-ray diffraction analysis showed that the crystalline structure of cellulose of flax fibers changed from cellulose-I structure to cellulose-II.     

TiO2/凹凸棒土复合催化剂的制备及光催化降解活性大红

以凹凸棒土作为载体,以 TiOSO4为钛源,采用超声分散-再沉淀法制备了 TiO2粒径为 10 nm 左右的锐钛矿型 TiO2/凹凸棒土复合催化剂.并采用 X 射线衍射仪、透射电子显微镜、X 射线能谱仪对复合催化剂进行了表征.制备复合催化剂的最佳条件:凹凸棒土与 TiO2的质量比为 1:3.0,煅烧温度为 450 ℃....     

Sb release characteristics of the solid waste produced in antimony mining smelting process

Sb release characteristics of blast furnace slag, mining waste rock and tailing sand were investigated in static immersion and dynamic leaching test. These three kinds of waste samples were collected from the antimony mine in Lengshuijiang, China, produced in mining smelting process. Effects of solid/liquid ratio, sample size and pH of leaching solution on Sb release characteristics were inspected based on the analysis of scanning electron microscope, pH and EC of leachate. The optimal parameters for Sb leaching of each sample were analyzed. For blast furnace slag and mining waste rock, Sb release contents increased along with the decline of solid/liquid ratio. The maximum accumulative release contents were 42.13, 34.26 mg/kg at the solid/liquid ratio of 1:20. While Sb release content for tailing sand decreased first and then increased with the reduction of solid/liquid ratio. When the solid/liquid ratio was 1:5, the accumulative Sb release content reached the most (24.30 mg/kg). Sb release content of mining waste rock increased with the drop of leaching solution pH, with the highest accumulative release content of 26.01 mg/kg at pH 2.0. Sb release contents of blast furnace slag and tailing sand showed positive correlation with the variation of leaching solution pH. The maximum accumulative release contents of these two samples were 215.91 and 147.83 mg/kg, respectively, when leaching solution pH was 7.0. In summary, Sb release capacity of the three samples in descending order was tailing sand, blast furnace slag and mining waste rock. pH and EC of the leachate in dynamic test varied independently with the initial pH of leaching solution while showing close relationship with mineral hydrolysis in the waste.     

Selection of palm oil mill effluent treatment for biogas generation or compost production using an analytic hierarchy process

Palm oil mill effluent (POME) is the liquid waste from palm oil mills, and is generally treated using open lagoon technology. However, open lagoons can also be combined with more environmentally friendly technologies. In this study, the analytic hierarchy process (AHP) was used to determine the best combination open lagoon of technology (COLT) for POME treatment. The selected criteria were benefit, opportunity, risk, and cost, with sub-criteria further determined based on these criteria. The sub-criteria were revenue, greenhouse gas reduction, employment absorption, corporate social responsibility, co-processing, environmental risk, marketing risk, technology reliability, investment cost, operation and maintenance cost, and opportunity cost. The alternatives were COLT-composting for fertilizer purpose and COLT-biogas for energy generation purpose. Calculation and analysis was performed on questionnaire data using Expert Choice^®. COLT-composting proved to be the superior COLT using tentative performance of alternative in this research, with advantages in benefit, opportunity, and risk. The priority weight for COLT-composting was 0.636. Sensitivity analysis was performed by changing criteria priorities. For COLT-biogas to be considered better than COLT-composting, the cost would need to be weighted more than 0.954.     

Leather Insole with Acupressure Effect: New Perspectives

Some wastes contain many reusable substances of high value. Solid leather waste is one such potential waste which can be converted into value added products. This study attempts to prepare leather insoles with acupressure effect from finished leather wastes and used leather wastes. Leather with acupressure effect (LAE) was fabricated using regenerated leather. LAE was characterized physico-chemically using Fourier transform infrared spectroscopy, thermo gravimetric analysis and scanning electron microscopy. Foot pressure measurements were done using LAE insoles on healthy individuals. Results proved that LAE insoles were able to increase the foot pressure of the wearer and thereby created an acupressure effect in them. Wearing of footwear with LAE insoles were beneficial compared to regular insoles. LAE possessed the required mechanical properties for insole production and it was also biodegradable in nature. The study proves that these composites could be successfully used for the production of cost-effective leather goods and therapeutic footwear. Production of useful byproducts from wastes is income generating and at the same time reduces environmental pollution and a feasible technology for waste recycling has been proved in this study.