Modelling Phosphorus Retention in Lakes and Reservoirs

Steady-state models for the prediction of P retention coefficient (R) in lakes were evaluated using data from 93 natural lakes and 119 reservoirs situated in the temperate zone. Most of the already existing models predicted R relatively successfully in lakes while it was seriously under-estimated in reservoirs. A statistical analysis indicated the main causes of differences in R between lakes and reservoirs: (a) distinct relationships between P sedimentation coefficient, depth, and water residence time; (b) existence of significant inflow–outflow P concentration gradients in reservoirs. Two new models of different complexity were developed for estimating R in reservoirs: , where τ is water residence time (year), was derived from the Vollenweider/Larsen and Mercier model by adding a calibrated parameter accounting for spatial P non-homogeneity in the water body, and is applicable for reservoirs but not lakes, and , where [P_in] is volume-weighted P concentration in all inputs to the water body (μg l⁻¹), was obtained by re-calibrating the OECD general equation, and is generally applicable for both lakes and reservoirs. These optimised models yield unbiased estimates over a large range of reservoir types.     

Mineralogical characterization of the Tournemire argillite after in situ interaction with concretes

This study aims to investigate, through mineralogical characterization (SEM, XRD) and mass-balance calculations, the effects of contact time, concrete types and presence of free water on the Tournemire argillite under in situ conditions. Three sampling zones from Excavation Disturbed Zone (EDZ) areas have been chosen: (1) dry contacts, collected at the tunnel masonry/argillite interface (contact time - 125 years), (2) wet contacts, taken close to drained areas below the tunnel roadbed in contact with the canal draining the Cernon fault water (contact time - 15 and 7 years) and at the tunnel masonry/argillite interface over 70 m from the Cernon fault (contact time - 125 years). This study shows that: in the absence of water, no significant modification of argillite is observed after 125 years, except for pyrite dissolution and gypsum precipitation; in the presence of water, precipitation of gypsum, recrystallization of mixed-layer clays, neoformation of zeolites and K-feldspars overgrowths are observed. At the concrete/argillite interface near the Cernon fault, important dolomite neoformation and leaching of chlorite and kaolinite occur. These processes are enhanced with contact time, low flow rate and the nature of the concrete (compound cement Portland CEM II 32.5). Evidence for oxidation processes linked to the EDZ (pyrite oxidation, Fe-oxy-hydroxide and gypsum precipitation) is observed.     

Carbonization of waste PVC to develop porous carbon material without further activation

Efficient removal of chlorine from PVC achieved by two-stage heat-treatment (280 and 410 degrees C) provided chlorine-free isotropic pitch containing additive. The pitch was stabilized and carbonized into porous carbons with surface areas of approximately 300 m2/g. Resultant porous carbons showed three pore structures of supermicropore, micropore and mesopore. The generation of CO2 from the decomposition of the CaCO3 additive in waste PVC is responsible for the development of porous structures. The surface area of the carbonized product increased after the removal of CaO.     

Municipal solid waste management in the Southern Province of Sri Lanka: problems, issues and challenges

This paper describes the problems, issues and challenges faced by Sri Lanka based on the outcome of a recent study conducted in the country's Southern Province. The study consists of a public survey, discussions with local authority staff involved in waste management, discussions with Provincial Council and Government officials, dialogue with local politicians, review of documents and field observations. The study revealed that only 24% of the households have access to waste collection and that in rural areas it was less than 2%. A substantial number of households in areas without waste collection expect local authorities to collect their waste. The study also showed that most sites in the province are under capacity to handle any increased demand. Urgent and immediate improvement of the waste disposal sites is necessary to meet the current demand for improved waste collection. The study also revealed that there is a high willingness of people for home composting.     

Classification of in-flight catering wastes in Egypt air flights and its potential as energy source (chemical approach)

Waste to energy conversion is based on the classification of waste. In-flight catering wastes resulting from Egypt Airlines economy class passengers were classified. The solid waste stream generated contains plastic, paper, left-over waste food and aluminum. The type of meal served varies according to the period of flight and so the quantity and content of the waste stream. It was found that the waste generation rate varied from 61.3 to 265 g according to the meal type. Breakfast snack meal generates the highest weight of waste which recorded an average of 265 g. Plastic waste generated varied from 39.6% to 64.6% by weight for the various types of meals served. A total amount of 725 tons were generated annually from organic waste (paper, plastic and food waste) among which a non combustible 39.4 tons of aluminum. The calorific value for each generated item is calculated and the total energy potential reached up to 14.3 TJ annually.     

A GIS based transportation model for solid waste disposal--a case study on Asansol municipality

Uncontrolled growth of the urban population in developing countries in recent years has made solid waste management an important issue. Very often, a substantial amount of total expenditures is spent on the collection of solid waste by city authorities. Optimization of the routing system for collection and transport of solid waste thus constitutes an important component of an effective solid waste management system. This paper describes an attempt to design and develop an appropriate storage, collection and disposal plan for the Asansol Municipality Corporation (AMC) of West Bengal State (India). A GIS optimal routing model is proposed to determine the minimum cost/distance efficient collection paths for transporting the solid wastes to the landfill. The model uses information on population density, waste generation capacity, road network and the types of road, storage bins and collection vehicles, etc. The proposed model can be used as a decision support tool by municipal authorities for efficient management of the daily operations for transporting solid wastes, load balancing within vehicles, managing fuel consumption and generating work schedules for the workers and vehicles. The total cost of the proposed collection systems is estimated to be around 80 million rupees for the fixed cost of storage bins, collection vehicles and a sanitary landfill and around 8.4 million rupees for the annual operating cost of crews, vehicles and landfill maintenance. A substantial amount (25 million rupees/yr) is currently being spent by AMC on waste collection alone without any proper storage/collection system and sanitary landfill. Over a projected period of 15 yr, the overall savings is thus very significant.     

Pilot project of mechanical-biological treatment of waste in Brazil

By mechanical-biological treatment (MBT) of residual municipal solid waste the behaviour of landfills can be significantly improved. After MBT the organic content (COD and BOD5), total organic carbon, and total nitrogen in the leachate, as well as the gas production rate, are reduced to values lower than 90% of the fresh untreated waste. The volume of the stabilized material to be disposed on landfills decreases enormously, by up to 70%. The monitoring effort for a landfill constructed under these conditions is reduced to a minimum and the stabilized material can be used in other ways, as material for reforestation, for cover material or for thermal utilization to produce energy. Environmental conditions are important in MBT, as well as waste characteristics. This paper describes the results of a pilot project of MBT performed in Rio de Janeiro, Brazil. The results have shown that this technology can be used successfully in developing countries, with economy for the society and important results for the environment.     

Mechanical-biological waste treatment and the associated occupational hygiene in Finland

A special feature of waste management in Finland has been the emphasis on the source separation of kitchen biowaste (catering waste); more than two-thirds of the Finnish population participates in this separation. Source-separated biowaste is usually treated by composting. The biowaste of about 5% of the population is handled by mechanical-biological treatment. A waste treatment plant at Mustasaari is the only plant in Finland using digestion for kitchen biowaste. For the protection of their employees, the plant owners commissioned a study on environmental factors and occupational hygiene in the plant area. During 1998-2000 the concentrations of dust, microbes and endotoxins and noise levels were investigated to identify possible problems at the plant. Three different work areas were investigated: the pre-processing and crushing hall, the bioreactor hall and the drying hall. Employees were asked about work-related health problems. Some problems with occupational hygiene were identified: concentrations of microbes and endotoxins may increase to levels harmful to health during waste crushing and in the bioreactor hall. Because employees complained of symptoms such as dry cough and rash or itching appearing once or twice a month, it is advisable to use respirator masks (class P3) during dusty working phases. The noise level in the drying hall exceeded the Finnish threshold value of 85 dBA. Qualitatively harmful factors for the health of employees are similar in all closed waste treatment plants in Finland. Quantitatively, however, the situation at the Mustasaari treatment plant is better than at some Finnish dry waste treatment plants. Therefore is reasonable to conclude that mechanical sorting, which produces a dry waste fraction for combustion and a biowaste fraction for anaerobic treatment, is in terms of occupational hygiene better for employees than combined aerobic treatment and dry waste treatment.     

Medical wastes management in the south of Brazil

Medical (clinical) wastes are costly in disposal and carry risks of infection, or physical injury, and of exposure to potentially harmful pharmaceuticals, as well as being aesthetically unacceptable. Technological advances in disposal, together with the introduction of rigorous emission standards for incinerators and similarly stringent control standards for non-burn “alternate” disposal technologies, continue to drive improvements in waste management. Are these improvements attainable in developing countries?Where adequate resources and a robust infrastructure are lacking, investment in advanced disposal technologies may be counterproductive. Developments must be appropriate to and manageable by the communities served; sustainable low-technology approaches may be preferable. There remains a need for affordable technical innovation, as well as underlying political support and international financial and technical assistance, to sustain meaningful improvements in waste management in remote and isolated regions and more generally in developing countries.     

复合污染状态下尾矿区有害化学品的迁移研究

用混合尾矿浆及尾矿渣淋溶柱,研究选矿药剂在尾矿渣及尾矿废水中的静态分布及其淋溶作用,结果表明:①选矿药剂对整个尾矿区都污染,即使是水溶性好的药剂,它们在尾矿渣中的静态分布也占有相当的比例,油溶性好的药剂多存在于尾矿渣中,尾矿污染为多种药剂的复合污染,各种药剂在尾矿渣及尾矿废水中的总浓度成倍加大;②用尾矿渣淋溶柱测得单一药剂的淋溶值:25号黑药>MIBC> CN->二号油>乙基黄药>丁基黄药>Y-89黄药.但多种药剂复合污染时,药剂的淋溶距离明显加大,其中CN-和Y-89黄药加大近一倍.复合药剂污染加大药剂的残留期,也加大它们向地下水及其它水源迁移的几率.