Fluxes of N2O, CH4 and CO2 in a meadow ecosystem exposed to elevated ozone and carbon dioxide for three years

Open-top chambers (OTCs) were used to evaluate the effects of moderately elevated O3 (40-50 ppb) and CO2 (+100 ppm) and their combination on N2O, CH4 and CO2 fluxes from ground-planted meadow mesocosms. Bimonthly measurements in 2002-2004 showed that the daily fluxes of N2O, CH4 and CO2 reacted mainly to elevated O3, while the fluxes of CO2 also responded to elevated CO2. However, the fluxes did not show any marked response when elevated O3 and CO2 were combined. N2O and CO2 emissions were best explained by soil water content and air and soil temperatures, and they were not clearly associated with potential nitrification and denitrification. Our results suggest that the increasing O3 and/or CO2 concentrations may affect the N2O, CH4 and CO2 fluxes from the soil, but longer study periods are needed to verify the actual consequences of climate change for greenhouse gas emissions.     

Use of Probabilistic Methods to Understand the Conservatism in California’s Approach to Assessing Health Risks Posed by Air Contaminants

Many state and federal agencies have prepared risk assessment guidelines, which describe methods for quantifying health risks associated with exposure to vapors and particulates emitted from point and area sources (e.g., California Air Pollution Control Officers Association [CAPCOA] under the Air Toxics “Hot Spots” Act [Assembly Bill 2588] and the U.S. Environmental Protection Agency [EPA] under the Clean Air Act). In general, these guidelines recommend or require the use of upper bound “point” estimates for numerous exposure parameters. This methodology yields a single risk estimate, which is intended not to underestimate the true risk and may significantly overstate it. This paper describes a risk assessment of a facility’s airborne emissions using a probabilistic approach, which presents a range and distribution of risk estimates rather than a single point estimate. The health risks to residents living near a food processing facility, as estimated using techniques recommended by California AB2588, are compared to the results of a probabilistic analysis. Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were identified as the emitted chemicals of concern. The point estimate method recommended by CAPCOA resulted in estimates that were greater than the 99.99th percentile risk predicted by the probabilistic analysis. As shown in other assessments of persistent airborne chemicals, secondary or indirect exposure pathways (i.e., ingestion of beef, ingestion of cow’s milk, and ingestion of mother’s milk) rather than inhalation, were the greatest contributors to risk. In this analysis, the probability distributions for the cancer potency factor and ingestion of cow’s milk had the largest impact on the results of the 33 exposure factors considered.     

Co-utilisation of CO2 and steelmaking slags for production of pure CaCO3 – legislative issues

The steel industry is characterised by large amounts of CO₂ emissions, but there is no easy means to reduce these emissions. One interesting option for the reduction of CO₂ emissions could be the utilisation of steelmaking slags for carbon dioxide mineralisation. In this option CO₂ is bound with the calcium of the slag material, producing stable carbonate as an end product. The utilisation of steelmaking slags as the raw material for carbon dioxide mineralisation will change the quality of the slags. If, however, this change degrades the slags it could prevent the use of slags in carbon dioxide mineralisation or make it very expensive.The purpose of the research presented here is to evaluate this issue with the help of a case study where the quality of the residual slag from the recently suggested carbonation method was experimentally investigated. The CO₂ mineralisation method, based on steelmaking slags and ammonium salt solutions, was found to change the quality of the slags: the calcium content was reduced, the CaO and Ca(OH)₂ phases were completely dissolved, and the solubility of the V and Cr increased notably. This residual slag would presumably have to be handled as waste. Currently, the steelmaking slag used in the case study is defined as a by-product, but if it is used for CO₂ mineralisation instead of liming its legal status will be re-evaluated. Subsequently, the CO₂ mineralisation process could possibly be defined as an end-of-waste procedure.     

A Comparison of In situ Vitrification and Rotary Kiln Incineration for Soils Treatment

In the hazardous waste community, the term “thermal destruction” is a catchallphrase that broadly refers to high temperature destruction of hazardous contaminants. Included in the thermal destruction category are treatment technologies such as rotary kiln incineration, fiuidized bed incineration, infrared thermal treatment, wet air oxidation, pyrolytic incineration, and vitrification. Among them, conventional rotary kiln incineration, a disposal method for many years, is the most well established, and often serves as a barometer to gauge the relative success of similar technologies. Public sentiment on environmental issues and increasingly stringent environmental regulations has, over time, spurred design and development of innovative thermal treatment processes directed toward reducing harmful emissions and residuals that may require further treatment or disposal. In situ vitrification (ISV), a technology that combines heat and immobiliztion, is one such innovative and relatively new technology.

This paper presents a comparison of ISV and rotary kiln incineration for soils treatment in the areas of process performance, process residuals, process limitations, applicable or relevant and appropriate (ARAJRs) regulations, criteria and limitations, and costs.