Acute and chronic impacts caused by aromatic hydrocarbons on bacterial communities at Boa Viagem and Forte do Rio Branco Beaches, Guanabara Bay, Brazil

The bacterial community presented significantly different hydrocarbonoclastic activity under acute and chronic impacts. Benzoic acid, toluene, benzene and xylene were used in final concentrations of 5, 10 and 15 mM and bacterial biomass was quantified through protein dosage. Under acute impact, the highest biomass percentages occurred between the 11th and 14th days; under chronic impact, between the 20th and 29th days. Under acute and chronic impacts, the bacterial biomass presented higher nutritional specialization at Boa Viagem Beach, using the aromatic hydrocarbons up to a concentration of 15 mM. Under acute impact, the concentration of the hydrocarbons constituted a critical factor for the bacterial flora from Forte do Rio Beach, because biomass increases only occurred in concentrations of 5 mM; under chronic impact, the aromatic hydrocarbons induced the specialization and increased bacterial biomass for 15 mM toluene. Benzoic acid (15 mM) was used by the bacteria from Boa Viagem and Forte do Rio Branco Beaches.     

Determination of Q1, an unknown organochlorine contaminant, in human milk, Antarctic air, and further environmental samples

Q1, an organochlorine component with the molecular formula C(9)H(3)Cl(7)N(2) and of unknown origin was recently identified in seal blubber samples from the Namibian coast (southwest of Africa) and the Antarctic. In these samples, Q1 was more abundant than PCBs and on the level of DDT residues. Furthermore, Q1 was more abundant in seals from the Antarctic than the Arctic. To prove this assumption, gas chromatography-electron-capture negative ion mass spectrometry (GC/ECNI-MS), which is sensitive and selective for Q1, allowed for screening of traces of Q1 even in samples with particularly high levels of other organochlorine contaminants. Q1 was isolated by high-performance liquid chromatography (HPLC) from a skua liver sample. A 1:1 mixture with trans-nonachlor in electron-capture detectors (ECDs) was used to determine the relative response factor with ECNI-MS. The ECNI-MS response of Q1 turned out to be 4.5 times higher than that of trans-nonachlor in an ECD. With GC/ECNI-MS in the selected ion-monitoring mode, four Antarctic and four Arctic air samples were investigated for the presence of Q1. In the Antarctic air samples, Q1 levels ranged from 0.7 to 0.9 fg/m(3). In Arctic air samples, however, Q1 was below the detection limit (<0.06 fg/m(3) or 60 ag/m(3)). We also report on high Q1 levels in selected human milk samples (12-230 microg/kg lipid) and, therefore, suggested that the unknown Q1 is an environmental compound whose origin and distribution should be investigated in detail. Our data confirm that Q1 is a bioaccumulative natural organochlorine product. Detection of a highly chlorinated natural organochlorine compound in air and human milk is novel.     

Trace elements, organochlorines, polycyclic aromatic hydrocarbons, dioxins, and furans in lesser scaup wintering on the Indiana Harbor Canal

During the winter of 1993-94, male lesser scaup (Aythya affinis) were collected on the heavily polluted Indiana Harbor Canal (IHC), East Chicago, IN, USA, and examined for tissue contaminant levels. Lesser scaup collected on the IHC had higher concentrations of cadmium (Cd), mercury (Hg), selenium (Se), polychlorinated biphenyls (PCBs), selected organchlorine pesticides, polychlorinated dibenzodioxins, polychlorinated dibenzofurans, polycyclic aromatic hydrocarbons, and aliphatic hydrocarbons than reference birds. Of the scaup collected on the IHC, 44% had Cd concentrations in the liver considered above background for freshwater waterfowl (>3 microg/g dry wt.), 50% had Se concentrations in the liver above a level possibly harmful to the health of young and adult birds (>33 microg/g dry wt.), and 88% of the scaup carcasses exceeded the PCB human consumption guidelines for edible poultry in the USA (>3.0 microg/g lipid wt.). The ratio of pristane:n-heptadecane concentrations in 47% of lesser scaup collected on IHC was elevated above 1.0, which is indicative of chronic exposure to petroleum hydrocarbons.     

Genotoxicity of two novel pesticides for the earthworm, Eisenia fetida

In this paper, several studies were conducted to evaluate the genotoxicity of two pesticides, Imidacloprid and RH-5849, for earthworm (Eisenia fetida). Earthworms were exposed in different exposure systems to evaluate their acute toxicity and the genotoxicity of the two pesticides was evaluated by using the method of sperm deformity assessment, micronucleus test of root tip cells in Vicia faba, a mouse bone-marrow micronucleus test, and comet assay. LC(50) (interpolated concentration at which 50% mortality of test population occurs) for earthworms varied in different exposure systems. The results indicated that Imidacloprid was consistently more toxic than RH-5849 in all exposure systems. In this study, sperm deformity test was used to detect the potential adverse influences of pesticides on the reproduction of earthworms. The results demonstrated that significant induction of sperm deformity (p<0.01) and a dose-effect relationship displayed at Imidacloprid concentrations higher than 0.5 mg/kg dry soil. However, the sperm deformity frequency of groups exposed to RH-5849 did not show significant difference (p>0.05) from the control until the dose reached 100 mg/kg dry soil. The results of the V. faba micronucleus tests showed that micronuclei frequency of the exposed group did not show significant difference (p>0.05) from the control until the concentration of Imidacloprid and RH-5849 reached 100 mg/ml. The results of the mouse bone-marrow micronuclei test also indicate that two pesticides did not show significant effects (p>0.05) on the micronuclei frequency in mice bone-marrow cells until the dose reached 100 mg/kg for Imidacloprid and 300 mg/kg for RH-5849 (2/3 LD(50)). Although no genotoxicity was detected by using the micronucleus tests, the results of the comet assay showed that the two pesticides induce significant DNA damage (p<0.01) in earthworms and dose-effect relationships were displayed. The 'earthworm comet assay' is a rapid and sensitive way to screen chemicals or terrestrial environments for their DNA-damaging properties.     

In situ sequential treatment of a mixed contaminant plume

Groundwater plumes often contain a mixture of contaminants that cannot easily be remediated in situ using a single technology. The purpose of this research was to evaluate an in situ treatment sequence for the control of a mixed organic plume (chlorinated ethenes and petroleum hydrocarbons) within a Funnel-and-Gate. A shallow plume located in the unconfined aquifer at Alameda Point, CA, was found to contain up to 218,000 μg/l of cis-1,2 dichloroethene (cDCE), 16,000 μg/l of vinyl chloride (VC) and <1000 μg/l of 1,1 dichloroethene (1,1 DCE), trans-1,2 dichloroethene (trans-1,2 DCE) and trichloroethene (TCE). Total benzene, toluene, ethylbenzene and xylenes (BTEX) concentrations were <10,000 μg/l. Contaminated groundwater was funneled into a gate, 3.0 m wide, 4.5 m long and 6.0 m deep (keyed into the underlying aquitard) where treatment occurred. The initial gate segment consisted of granular iron, for the reductive dechlorination of the higher chlorinated ethenes. The second segment, the biosparge zone, promoted aerobic biodegradation of petroleum hydrocarbons and any remaining lesser-chlorinated compounds, stimulated by dissolved oxygen (DO) and carbon dioxide (CO₂) additions via an in situ sparge system (CO₂ was used to neutralize the high pH produced from reactions in the iron wall). Groundwater was drawn through the gate by pumping two wells located at the sealed, downgradient, end. Over a 4-month period an estimated 1350 g of cDCE flowed into the treatment gate and the iron wall removed 1230 g, or 91% of the mass. The influent mass of VC was 572 g and the iron wall removed 535 g, corresponding to 94% mass removal. The other chlorinated ethenes had significantly lower influent masses (3 to 108 g) and the iron wall removed the majority of the mass resulting in >96% mass removal for any of the compounds. In spite of these high removal percentages, laboratory column tests indicated that at these levels of chlorinated contaminants, surface saturation of the iron grains likely contributed to lower than expected reaction rates. In the biosparge zone, mass removal of cDCE appeared to occur predominantly by biodegradation (65%) with volatilization (35%) being an important secondary process. The dominant removal process for VC was volatilization (70%) although significant biodegradation was also indicated (30%). Laboratory microcosm results confirmed the potential for aerobic biodegradation of cDCE and VC. When average influent field concentrations for cDCE and VC were 220,000 and 46,000 μg/l, respectively, the sequential treatment unit removed 99.6% of the total mass and when the influent concentrations decreased to 26,000 and 19,000 μg/l for cDCE and VC, respectively, >99.9% removal within the treatment gate was attained. BTEX compounds were found to be significantly retarded in the iron treatment zone. Although they did eventually break through the granular iron, and into the gravel transition zone, none of these compounds was detected in the biosparge zone. No noticeable interferences between the anaerobic (reductive) and aerobic parts of the system occurred during testing. The results of this experiment show that in situ treatment sequences are viable, although further work is needed to optimize performance.     

Plant-promoted pyrene degradation in soil

A study was conducted to investigate the capability of nine plant species to promote the degradation of pyrene in soil. The test method allowed for analysis of the entire sample of soil. More pyrene was degraded in the presence of roots of all nine species than in unplanted soil. Within approximately 8 weeks, as much as 74% of the pyrene disappeared from vegetated soil compared to 40% or less from unplanted soil. The data suggest that some of the test species may be especially useful for phytoremediation of soils contaminated with PAHs.     

Flotation of metal-loaded clay anion exchangers. Part I: the case of chromates

Synthetic hydrotalcite-like layered materials are known for their ability to remove anions, like the chromates. These sorbents usually exist in powder form, thereby exhibiting high surface area and rapid kinetics for adsorption, but presenting appreciable problems in the subsequent solid/liquid separation process. Almost complete removals were obtained in this paper, from batchwork dispersed-air flotation in presence of a flocculant. Due to the experienced difficulty of flotation of thermally activated (at 500 degrees C) hydrotalcite metal-loaded particles, the application of various surfactants was studied. Continuous-flow laboratory runs certified also the effectiveness of this combined process of sorptive flotation, a promising innovative treatment technology.     

PCDD/F inhibition by prior addition of urea to the solid fuel in laboratory experiments and results statistical evaluation

The objectives of this work were to study the effect of urea addition to the fuel before the combustion on the suppression of PCDD/F emissions, to examine the influence of urea to PCDD/F isomer patterns by employing statistical analysis techniques and to determine the most effective method of urea addition. Urea in the form of powder and as an aqueous solution was mixed with RDF and the fuel mixtures were incinerated in a lab-scale reactor at 1000 degrees C. PCDD/F emitted during combustion experiments were collected in a quartz wool filter downstream the reactor unit. Analysis and quantification of PCDD/F showed that urea significantly affected PCDD/F emissions. Combustion of RDF containing 10% w/w urea resulted in PCDD/F emissions lower than 8 I-TEQ ng/g RDF, while the corresponding average value from single RDF combustion was 17 I-TEQ ng/g RDF. The PCDD/F prevention capacity of urea was independent from the method of urea addition to the fuel, as similar results were obtained after the addition of urea in the solid and in the aqueous phases. Results assessment by statistical methods showed that isomer patterns remained almost stable and were not affected by the method of urea addition.     

PAH and soot emissions from burning components of medical waste: examination/surgical gloves and cotton pads

This is a laboratory investigation on the emissions from batch combustion of representative infectious ("red bag") medical waste components, such as medical examination latex gloves and sterile cotton pads. Plastics and cloth account for the majority of the red bag wastes by mass and, certainly, by volume. An electrically heated, horizontal muffle furnace was used for batch combustion of small quantities of shredded fuels (0.5-1.5 g) at a gas temperature of approximately 1000 degrees C. The residence time of the post-combustion gases in the furnace was approximately 1 s. At the exit of the furnace, the following emissions were measured: CO, CO2, NOx, particulates and polynuclear aromatic compounds (PACs). The first three gaseous emissions were measured with continuous gas analyzers. Soot and PAC emissions were simultaneously measured by passing the furnace effluent through a filter (to collect condensed-phase PACs) and a bed of XAD-4 adsorbent (to capture gaseous-phase PACs). Analysis involved soxhlet extraction, followed by gas chromatography-mass spectrometry (GC-MS). Results were contrasted with previously measured emissions from batch combustion of pulverized coal and tire-derived fuel (TDF) under similar conditions. Results showed that the particulate soot) and cumulative PAC emissions from batch combustion of latex gloves were more than an order of magnitude higher than those from cotton pads. The following values are indicative of the relative trends (but not necessarily absolute values) in emission yields: 26% of the mass of the latex was converted to soot, 11% of which was condensed PAC. Only 2% of the mass of cotton pads was converted to soot, and only 3% of the weight of that soot was condensed PAC. The PAC yields from latex were comparable to those from TDF. The PAC yields from cotton were higher than those from coal. A notable exception to this trend was that the three-ring gas-phase PAC yields from cotton were more significant than those from latex. Emission yields of CO and CO2 from batch combustion of cotton were, respectively, comparable and higher than those from latex, despite the fact that the carbon content of cotton was half that of latex. This is indicative of the more effective combustion of cotton. Nearly all of the mass of carbon of cotton gasified to CO and CO2 while only small fractions of the carbon in latex were converted to CO2 and CO (20% and 10%, respectively). Yields of NOx from batch combustions of latex and cotton accounted for 15% and 12%, respectively, of the mass of fuel nitrogen indicating that more fuel nitrogen was converted to NOx in the former case, possibly due to higher flame temperatures. No SO2 emissions were detected, indicating that during the fuel-rich combustion of latex, its sulfur content was converted to other compounds (such as H2S) or remained in the soot.     

Evidence for the contribution of methane in the formation of aromatics and soot in fuel-rich pre-mixed combustion

Experimental results from an isothermal laminar flow reactor at atmospheric pressure are presented on the chemical composition in the post-oxidative region of two sooting fuel-rich pre-mixed mixtures diluted in nitrogen. A base case composed of n-heptane and O2 in N2 at 1425 K with a C/O of 2.85 was perturbed by substituting 10% of the carbon in n-heptane with carbon as CH4. While these changes would intuitively reduce aromatics and soot formation by increasing H2 and decreasing C2H2 concentrations, we observe the opposite. The concentrations of individual aromatic species are observed to actually increase by up to 50% and the soot yield increases by 80%.