Enhanced biological phosphorus removal using thermal alkaline hydrolyzed municipal wastewater biosolids

This study reports the feasibility of using municipal wastewater biosolids as an alternative carbon source for biological phosphorus removal. The biosolids were treated by a lowtemperature, thermal alkaline hydrolysis process patented by Lystek International Inc.(Cambridge, ON, Canada) to produce short-chain volatile fatty acids and other readily biodegradable organics. Two sequencing batch reactors(SBRs) were operated with synthetic volatile fatty acids(Syn VFA) and readily biodegradable organics produced from the alkaline hydrolysis of municipal wastewater biosolids(Lystek) as the carbon source, respectively.Municipal wastewaters with different strengths and COD:N:P ratios were tested in the study. The reactors' performances were compared with respect to nitrogen and phosphorus removal. It was observed that phosphorus removal efficiencies were between 98%–99% and 90%–97% and nitrogen removal efficiencies were 78%–81%, and 67% for the Syn VFA and Lystek, respectively. However, the kinetics for phosphorus release and uptake during the anaerobic and aerobic stages with Lystek were observed to be significantly lower than Syn VFA due to the presence of higher order VFAs(C4 and above) and other fermentable organics in the Lystek.     

Silica-quaternary ammonium “Fixed-Quat” nanofilm coated fiberglass mesh for water disinfection and harmful algal blooms control

Intensification of pollution loading worldwide has promoted an escalation of different types of disease-causing microorganisms, such as harmful algal blooms(HABs), instigating detrimental impacts on the quality of receiving surface waters. Formation of unwanted disinfection by-products(DBPs) resulting from conventional disinfection technologies reveals the need for the development of new sustainable alternatives. Quaternary Ammonium Compounds(QACs) are cationic surfactants widely known for their effective biocidal properties at the ppm level. In this study, a novel silica-based antimicrobial nanofilm was developed using a composite of silica-modified QAC(Fixed-Quat) and applied to a fiberglass mesh as an active surface via sol–gel technique. The synthesized Fixed-Quat nanocoating was found to be effective against E. coli with an inactivation rate of 1.3 × 10~(-3) log reduction/cm min. The Fixed-Quat coated fiberglass mesh also demonstrated successful control of Microcystis aeruginosa with more than 99% inactivation after 10 hr of exposure.The developed antimicrobial mesh was also evaluated with wild-type microalgal species collected in a water body experiencing HABs, obtaining a 97% removal efficiency. Overall,the silica-functionalized Fixed-Quat nanocoating showed promising antimicrobial properties for water disinfection and HABs control, while decreasing concerns related to DBPs formation and the possible release of toxic nanomaterials into the environment.     

Monitoring biofouling based on aerobic respiration in reverse osmosis system

A monitoring method of biofouling in reverse osmosis (RO) system was proposed based on the fluorescent signal of resorufin, which is reduced by nicotinamide adenine dinucleotide released from viable cells during aerobic respiration. The fluorescent signal of resorufin reduced by planktonic cells and microorganisms of biofilm showed linearity, indicating its feasibility to monitor biofouling in a RO system. For the application of the method to the lab-scale RO system, the injection concentration of resazurin and the injection flow rate were optimized. Biofilm on RO membranes continuously operated in a lab-scale RO system was estimated by resorufin fluorescence under optimized detection condition. As a result, resorufin fluorescence on RO membrane showed a significant increase in which the permeability of RO system decreased by 30.48%. Moreover, it represented the development of biofilm as much as conventional biofilm parameters such as adenosine triphosphate, extracellular polymeric substances, and biofilm thickness. The proposed method could be used as a sensitive and low-cost technology to monitor biofouling without autopsy of membranes.     

Facile synthesis of graphitic carbon-nitride supported antimony-doped tin oxide nanocomposite and its application for the adsorption of volatile organic compounds

Antimony-doped tin oxide(ATO) nanoparticles with an average size of ～ 6 nm were prepared by co-precipitation and subsequent heat treatment. Graphitic carbon nitride(g-CN)/ATO hybrid nanocomposite was designed by the combination of thermally synthesized g-CN and ATO nanoparticles by ultrasonication. The materials were characterized using N2 adsorption/desorption(BET), X-ray diffraction(XRD), scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), transmission electron microscopy(TEM) and Fourier transform infrared spectroscopy(FTIR). A mixture of five volatile organic compounds(VOCs, chloroform, benzene, toluene, xylene and styrene) was used to compare the adsorption capacity of the samples. The adsorption capacity of ATO nanoparticles was improved by the addition of g-CN. Experimental data showed that, among the five VOCs,chloroform was the least adsorbed, regardless of the samples. The g-CN/ATO showed nearly three times greater adsorption capacity for the VOC mixture than pure ATO. The unchanged efficiency of VOC adsorption during cyclic use demonstrated the completely reversible adsorption and desorption behavior of the nanocomposite at room conditions. This economically and environmentally friendly material can be a practical solution for outdoor and indoor VOC removal.     

Impact of combining chlorine dioxide and chlorine on DBP formation in simulated indoor swimming pools

The main objective of this study was to assess the combined use of chlorine dioxide (ClO2) and chlorine (Cl2) on the speciation and kinetics of disinfection by-product (DBP) formation in swimming pools using synthetic pool waters prepared with a body fluid analog (BFA) and/or fresh natural water. At 1:25 (mass ratio) of ClO2 to Cl2, there was no significant reduction in the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) for both BFA solution and natural water compared to the application of Cl2 alone. When the mass ratio of ClO2 to Cl2 increased to 1:1, substantial decreases in both THMs and HAAs were observed in the natural water, while there was almost no change of DBP formations in the BFA solution. Haloacetonitriles and halonitromethanes levels in both water matrices remained similar. In the presence of bromide, the overall DBP formation increased in both BFA solution and natural water. For the DBP formation kinetics, after 72 hr of contact time, very low formation of THMs and HAAs was observed for the use of ClO2 only. Compared to Cl2 control, however, applying the 1:1 mixture of ClO2/Cl2 reduced THMs by > 60% and HAAs by > 50%. Chlorite was maintained below 1.0 mg/L, while the formation of chlorate significantly increased over the reaction time. Finally, in a bench-scale indoor pool experiment, applying ClO2 and Cl2 simultaneously produced less THMs compared to Cl2 control and kept chlorite at < 0.4 mg/L, while HAAs and chlorate accumulated over 4-week operation period.     

Characterization of particulate matter from diesel passenger cars tested on chassis dynamometers

Emission characterization of particle number as well as particle mass from three diesel passenger cars equipped with diesel particulate filter(DPF), diesel oxidation catalyst(DOC)and exhaust gas recirculation(EGR) under the vehicle driving cycles and regulatory cycle.Total particle number emissions(PNEs) decreased gradually during speed-up of vehicle from 17.3 to 97.3 km/hr. As the average vehicle speed increases, the size-segregated peak of particle number concentration shifts to smaller size ranges of particles. The correlation analysis with various particulate components such as particle number concentration(PNC),ultrafine particle number concentration(UFPNC) and particulate matter(PM) mass was conducted to compare gaseous compounds(CO, CO_2, HC and NOx). The UFPNC and PM were not only emitted highly in Seoul during severe traffic jam conditions, but also have good correlation with hydrocarbons and NOxinfluencing high potential on secondary aerosol generation. The effect of the dilution temperature on total PNC under the New European Driving Cycle(NEDC), was slightly higher than the dilution ratio. In addition, the nuclei mode(DP: ≤ 13 nm) was confirmed to be more sensitive to the dilution temperature rather than other particle size ranges. Comparison with particle composition between vehicle speed cycles and regulatory cycle showed that sulfate was slightly increased at regulatory cycle, while other components were relatively similar. During cold start test, semivolatile nucleation particles were increased due to effect of cold environment. Research on particle formation dependent on dilution conditions of diesel passenger cars under the NEDC is important to verify impact on vehicular traffic and secondary aerosol formation in Seoul.     

Effects of Soundscapes on Perceived Crowding and Encounter Norms

Soundscapes in recreation settings are becoming an important issue, but there are few studies of the effects of sounds on recreation experiences, especially crowding perceptions and encounter norms. This study compared effects of six types of sounds (an airplane, a truck engine, children playing, birds, water, and a control) on perceived crowding (PC) and encounter norms for hikers. Data were collected from 47 college students through lab experiments using simulated images, with moving hikers inserted in the original photo taken in the Jungmeori area of Mudeungsan Provincial Park in Korea. Overall, the motor-made sounds of the airplane and truck engine increased PC and decreased acceptability ratings, and the natural sounds of birds and water decreased PC and increased acceptability ratings. Ratings of the sound of children playing were similar to those in the control (i.e., no sound). In addition, as numbers of hikers increased, the overall effects of sounds decreased, and there were few significant differences in PC or acceptability ratings at the highest encounter levels. Theoretical and methodological implications are discussed.     

Geochemical distribution of trace element concentrations in the vicinity of Boroo gold mine,Selenge Province,Mongolia

The environmental impacts of Boroo gold mine project in Mongolia was evaluated by chemical characterization of trace element concentrations in water, soils and tailing dam sediment samples. The results showed that concentrations of B, Cd, Ni and Se in the water samples were within the accepted levels of the Mongolia water quality standard (MNS4586: 1998). However, the concentrations of Al, As, Cu, Mn, Fe, Pb, U and Zn were higher than the maximum allowable concentration especially in the monitoring and heap leach wells. The average concentrations of As, Cd, Cu, Ni, Pb and Zn in the tailing dam sediment were 4419, 58.5, 56.0, 4.8, 20.6 and 25.7 mg/kg, respectively. Generally, arsenic and heavy metals in the soil samples were within the acceptable concentrations of the soil standard of Mongolia (MNS 5850: 2008). The chemical characterization of As solid phase in tailing dam sediment showed that the majority of As were found in the residual fraction comprising about 74% of total As. Assessing the potential risk to humans, simple bioavailability extraction test was used to estimate bioavailability of arsenic and heavy metals, and the concentrations extracted from tailing dam sediment were; 288.2 mg/kg As, 7.2 mg/kg Cd, 41.1 mg/kg Cu, 13.5 mg/kg Pb, 4.7 mg/kg Ni and 23.5 mg/kg Zn, respectively. From these results, the Boroo gold mine project has presently not significantly impacted the environment, but there is a high probability that it may act as a source of future contamination.     

Size-selective sampling of particulates using a physiologic sampling pump

Recent laboratory research indicates physiologic sampling of gas and vapor may provide more representative estimates of personal exposures than traditional methods. Modifications to the physiologic sampling pump (PSP) used in that research are described which extend its usefulness to size-selective sampling of particulates. PSPs used in previous research varied motor speed to keep sampling proportional to the subject's inhalation. This caused airflow and particle velocities through the collection device to continually change making those pumps unsuitable for sampling particulates. The modified implementation of the PSP pulls a constant airflow into and through a cyclone, then uses valves to either direct the airflow through, or divert the airflow around, the sampling filter. By using physiologic inputs to regulate the fraction of each second that air flows through the sampling filter, samples may be collected in proportion to inhalation rate. To evaluate the performance of a functional prototype 5 different sizes of monodisperse aerosols of ammonium fluorescein were generated by a vibrating orifice aerosol generator and introduced into a calm air chamber. To simulate different inhalation rates the valves of the PSP were energized using 9 different duty cycles. Efficiency curves are presented and compared to a standard respirable convention by bias mapping. The performance of the modified cyclone used in the PSP sampling head compared favorably with a commercially available cyclone of the same model, operating at a constant airflow (± 10% over almost all the size distributions of concern). The new method makes physiologic sampling of the respirable fraction of particulates feasible.