Heavy trucks, conspicuity treatment, and the decline of collision risk in darkness

IntroductionThe influence of amendments to Federal Motor Vehicle Safety Standard (FMVSS) 108, requiring conspicuity treatments on heavy tractors and trailers, was determined in analyses of the odds of fatal collisions in darkness.MethodComparisons were made between crashes in which conspicuity treatment was likely relevant, and those in which it was likely irrelevant.ResultsOver 23 years, the odds that a fatal collision involving a heavy truck occurred in darkness declined by 58% among relevant crashes, while little decline was observed for irrelevant crashes. Disaggregation into crash types revealed the largest declines occurred in fatal rear-end and angle collisions. A parallel analysis of light vehicles also found declines but no differences among crash type. Similar trends were also observed for nonfatal rear end collisions.ConclusionThe results suggest that detection failure may have contributed to the risk of striking a tractor-semitrailer in darkness, and that conspicuity treatments have reduced this risk.Impact on IndustryConspicuity treatments appear to reduce risk of collision into heavy trucks in darkness. It is likely that this benefit would also extend to other vehicles that are not included in the FMVSS 108 regulation (e.g., buses, single unit trucks, recreational vehicles), although many are so equipped, regardless of the regulation.     

Prediction of thermal hazards from fireballs

Various models of fireball diameter have been evaluated by statistical techniques. The model of Gayle for fireball diameter estimation showed good agreement between the predicted and experimental data. The models relating to fireball duration, transmissivity and view factor have been selected based on their relative merits. A user interactive computer program has been developed to predict thermal hazards from fireballs in chemical process industries.     

Modelling of moisture-dependent aerobic degradation of solid waste

In landfill, high temperature levels come from aerobic reactions inside the waste surface layer. They are known to make anaerobic processes more reliable, by partial removal of easily biodegradable substrates. Aerobic biodegradation of the main components of biodegradable matter (paper and cardboard waste, food and yard waste) is considered. In this paper, two models which take into account the effect of moisture on aerobic biodegradation kinetics are discussed. The first one (Model A) is a simple, first order, substrate-related model, which assumes that substrate hydrolysis is the limiting step of the process. The second one (Model B) is a biomass-dependant model, considering biological growth processes. Respirometric experiments were performed in order to evaluate the efficiency of each model. The biological oxygen demands of shredded paper and cardboard samples and of food and yard waste samples prepared at various initial water contents were measured. These experimental data were used to identify model parameters. Model A, which includes moisture dependency on the maximum amount of biodegraded matter, is relevant for paper and cardboard biodegradation. On the other hand, Model B, including moisture effect on the growth rate of biomass is suitable to describe food and yard waste biodegradation.     

The Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-Lactide) Prepared by Different Synthesis Procedure

Different synthesis methods were applied to determine optimal conditions for polymerization of (3S)-cis-3,6-dimethyl-1,4-dioxane-2,5-dione (l-lactide), in order to obtain poly(l-lactide) (PLLA). Bulk polymerizations (in vacuum sealed vessel, high pressure reactor and in microwave field) were performed with tin(II) 2-ethylhexanoate as the initiator. Synthesis in the vacuum sealed vessel was carried out at the temperature of 150 °C. To reduce the reaction time second polymerization process was carried out in the high pressure reactor at 100 °C and at the pressure of 138 kPa. The third type of rapid synthesis was done in the microwave reactor at 100 °C, using frequency of 2.45 GHz and power of 150 W at the temperature of 100 °C. The temperature in this method was controlled via infrared system for in-bulk measuring. The solution polymerization (with trifluoromethanesulfonic acid as initiator) was possible even at the temperature of 40 °C, yielding PLLA with narrow molecular weight distribution in a very short period of time (less than 6 h). The obtained polymers had the number-average molecular weights ranging from 43,000 to 178,000 g mol⁻¹ (polydispersity index ranging from 1 to 3) according to the gel permeation chromatography measurements. The polymer structure was characterized by Fourier transform infrared and NMR spectroscopy. Thermal properties of the obtained polymers were investigated using thermogravimetry and differential scanning calorimetry.     

The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.     

Mobility control: How injected surfactants and biostimulants may be forced into low‐permeability units

Recovering dense nonaqueous‐phase liquid (DNAPL) remains one of the most difficult problems facing the remediation industry. Still, the most common method of recovering DNAPL is to physically remove the contaminants using common technologies such as total fluids recovery pumps, vacuum systems, and “pump‐and‐treat.” Increased DNAPL removal can be attained using surfactants to mobilize and/or solubilize the pollutants. However, very little is understood of the methods developed by petroleum engineers beginning in the 1960s to overcome by‐passed, low‐permeability zones in heterogeneous oil reservoirs. By injecting or causing the formation of viscous fluids in the subsurface, petroleum engineers caused increased in‐situ pressures that forced fluid flow into low permeability units as well as the higher permeability thief zones. Polymer flooding involves injecting a viscous aqueous polymer solution into the contaminated aquifer. Foam flooding involves injecting surfactant to decontaminate the high‐permeability zones and then periodic pulses of air to cause a temporary viscous foam to form in the high‐permeable zones after all DNAPL is removed. Later surfactant pulses are directed by the foam into unswept low‐permeable units. These methods have been applied to DNAPL removal using surfactants but they can also be applied to the injection of bio‐amendments into low‐permeability zones still requiring continued remediation. Here we discuss the principles of mobility control as practiced in an alluvial aquifer contaminated with chlorinated solvent and coal tar DNAPLs as well as some field results. © 2003 Wiley Periodicals, Inc.