Characterization and Identification of the Sources of Chromium, Zinc, Lead, Cadmium, Nickel, Manganese and Iron in Pm10 Particulates at the Two Sites of Kolkata, India

Monitoring of ambient PM₁₀ (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 μm aerodynamic diameter) has been done at residential (Kasba) and industrial (Cossipore) sites of an urban region of Kolkata during November 2003 to November 2004. These sites were selected depending on the dominant anthropogenic activities. Metal constituents of atmospheric PM₁₀ deposited on glass fibre filter paper were estimated using Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). Chromium (Cr), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), manganese (Mn) and iron (Fe) are the seven toxic trace metals quantified from the measured PM₁₀ concentrations. The 24 h average concentrations of Cr, Zn, Pb, Cd, Ni, Mn and Fe from ninety PM₁₀ particulate samples of Kolkata were found to be 6.9, 506.1, 79.1, 3.3, 7.4, 2.4 and 103.6 ng/m³, respectively. The 24 h average PM₁₀ concentration exceeded national ambient air quality standard (NAAQS) as specified by central pollution control board, India at both residential (Kasba) and industrial (Cossipore) areas with mean concentration of 140.1 and 196.6 μg/m³, respectively. A simultaneous meteorology study was performed to assess the influence of air masses by wind speed, wind direction, rainfall, relative humidity and temperature. The measured toxic trace metals generally showed inverse relationship with wind speed, relative humidity and temperature. Factor analysis, a receptor modeling technique has been used for identification of the possible sources contributing to the PM₁₀. Varimax rotated factor analysis identified four possible sources of measured trace metals comprising solid waste dumping, vehicular traffic with the influence of road dust, road dust and soil dust at residential site (Kasba), while vehicular traffic with the influence of soil dust, road dust, galvanizing and electroplating industry, and tanning industry at industrial site (Cossipore).     

Catchment-Wide Wetland Assessment and Prioritization Using the Multi-Criteria Decision-Making Method TOPSIS

It is widely accepted that wetland ecosystems are under threat worldwide. Many communities are now trying to establish wetland rehabilitation programs, but are confounded by a lack of objective information on wetland condition or significance. In this study, a multi-criteria decision-making method, TOPSIS (the Technique for Order Preference by Similarity to Ideal Solution), was adapted to assist in the role of assessing wetland condition and rehabilitation priority in the Clarence River Catchment (New South Wales, Australia). Using 13 GIS data layers that described wetland character, wetland protection, and wetland threats, the wetlands were ranked in terms of condition. Through manipulation of the original model, the wetlands were prioritized for rehabilitation. The method offered a screening tool for the managers in choosing potential candidate wetlands for rehabilitation in a region.     

Constructed wetland microcosms as sustainable technology for domestic wastewater treatment: an overview

Environmental Science and Pollution Research - Constructed wetland microcosms (CWMs) are artificially designed ecosystem which utilizes both complex and ordinary interactions between supporting...     

The use of ultra filtration in trace metal speciation studies in sea water

During this work, size fractionation technique "ultra filtration" is used in speciation studies of trace elements in the coastal sea water. Filtration is the most commonly used method to fractionate trace metal species, but often only "dissolved" and "particulate" fraction. The purpose of the present study is to determine colloidal and suspended particulate concentrations of Fe, Zn, Cu, Ni, and Mn in sea water. Suspended particulate matter were separated in three different size groups namely (>2.7 microm, <2.7->0.45 microm and <0.45->0.22 microm) by suction filtration using cellulose acetate and nitrate filter membranes. Thereafter to concentrate the solution with colloidal particle <0.22 microm-1.1 nm (0.5 k Nominal Molecular Weight cut-off Limit {NMWL}), the solution obtained from filtration through <0.22 microm, is sequentially passed through the ultra-filtration membranes having pore diameters of 14 nm (300 k NMWL), 3.1 nm (50 k NMWL), 2.2 nm (30 k NMWL), 1.6 nm (10 k NMWL) and 1.1 nm (0.5 k NMWL) by using Stirred Ultra-filtration Cells, operating in concentration mode. The concentration of Fe, Zn, Cu, Ni, and Mn were measured in suspended and dissolved fraction by ion chromatography, ICP-AES and Atomic Absorption Spectrometer. The salinity of the solution in various dissolved fractions of sequential filtration varies between 30.89-34.22 parts per thousand. The maximum concentrations of colloidal Zn, Cu, Ni and Mn in dissolved fraction were in <2.2->1.6 nm fraction. In case of Fe, colloidal fractions <2.2->1.6 nm and <1.6-<1.1 nm shows higher concentration. The concentration of Zn, Cu, Ni and Mn increase with decrease in size in suspended particulate matter, while the reverse is observed in case of Fe. This size separation data that specifies the partitioning of metals between dissolved and suspended solid phases is necessary for developing physically based models of metal transport in aquatic system.     

The synergistic effect of air mass on outdoor performance for different PV module in India

The effect of air mass (AM) on the performance of multi-crystalline silicon (m-Si), amorphous silicon (a-Si), and hetero-junction with intrinsic thin layer (HIT)-technology-based photovoltaic (PV) modules are evaluated for representative day of four seasons during the year 2011 for composite climate of India. To find the best performing PV module technology with respect to AM at the site, annual energy yields and performance ratio against different AM bands (AM 1–4.5) are plotted. It is found that HIT modules perform better than m-Si and a-Si at each AM band. Annual energy yields for all three technologies decrease with increasing order of AM bands. The performance ratio for HIT and m-SI modules initially increases and then decreases with increasing order of AM bands. However, for a-Si modules, the performance ratio decreases with increasing order of the AM bands.     

Molasses-based growth and lipid production by Chlorella pyrenoidosa: A potential feedstock for biodiesel

Biodiesel provides a feasible solution to the twin crisis of energy security and environmental concerns prevalent today, and it can be extracted from conventional oil crops as well as microalgae. However, lipid productivity in case of microalgae is much higher and has several advantages as compared with crop plants, so it is a better feedstock for biodiesel. In case of Chlorella pyrenoidosa, the heterotrophic cultured cells were found to be better in terms of lipid production, and ultimately biodiesel production, but the bottleneck is that in this mode glucose is used to feed the cells, which amounts to almost 80% of the total cost of biodiesel production. The purpose of this study is to evaluate and highlight the feasibility of using the industrially cheap cane molasses as a carbon source in place of glucose for a large-scale, low-cost lipid production of Chlorella pyrenoidosa. When treated molasses was used as a carbon source instead of glucose, the biomass sharply increases from 0.89 to 1.22 g L^–1. On the other hand, the total lipid content increases from 0.27 to 0.66 g g^–1. The specific growth rate and yield was higher in treated molasses as compared with that in glucose-supplemented. A mathematical model was also developed based on logistic, Luedeking–Piret, and Luedeking-Piret-like equations. Model predictions were in satisfactory agreement with the measured data, and the mode of lipid production was growth-associated.     

Photodegradation of Oryzalin in aqueous isopropanol and acetonitrile

The phototransformation of Oryzalin was studied under UV light (λ_max ≥ 290 nm) and sunlight (λ_max ≥ 250 nm) in aqueous isopropanol and acetonitrile solution in absence and presence of TiO₂ as sensitizer. The rate of photodegradation of Oryzalin in different solvent system followed first-order kinetics, and calculated half-lives were found to be in the range of 23.52-53.75 h for UV light and 41.23-61.43 h for sunlight. From this study, total 12 photoproducts were identified and characterized on the basis of column chromatography and Q-Tof micromass spectral data. The plausible mechanism of phototransformation involved was hydrolysis, breaking of sulfonic bond, and loss of amino and sulfonic acid group.     

Emerging trends in photodegradation of petrochemical wastes: a review

Various human activities like mining and extraction of mineral oils have been used for the modernization of society and well-beings. However, the by-products such as petrochemical wastes generated from such industries are carcinogenic and toxic, which had increased environmental pollution and risks to human health several folds. Various methods such as physical, chemical and biological methods have been used to degrade these pollutants from wastewater. Advance oxidation processes (AOPs) are evolving techniques for efficient sequestration of chemically stable and less biodegradable organic pollutants. In the present review, photocatalytic degradation of petrochemical wastes containing monoaromatic and poly-aromatic hydrocarbons has been studied using various heterogeneous photocatalysts (such as TiO₂, ZnO and CdS. The present article seeks to offer a scientific and technical overview of the current trend in the use of the photocatalyst for remediation and degradation of petrochemical waste depending upon the recent advances in photodegradation of petrochemical research using bibliometric analysis. We further outlined the effect of various heterogeneous catalysts and their ecotoxicity, various degradation pathways of petrochemical wastes, the key regulatory parameters and the reactors used. A critical analysis of the available literature revealed that TiO₂ is widely reported in the degradation processes along with other semiconductors/nanomaterials in visible and UV light irradiation. Further, various degradation studies have been carried out at laboratory scale in the presence of UV light. However, further elaborative research is needed for successful application of the laboratory scale techniques to pilot-scale operation and to develop environmental friendly catalysts which support the sustainable treatment technology with the “zero concept” of industrial wastewater. Nevertheless, there is a need to develop more effective methods which consume less energy and are more efficient in pilot scale for the demineralization of pollutant.     

Two-echelon closed-loop supply chain deterministic inventory models in a batch production environment

This paper considers a two-echelon closed-loop supply chain consisting of a manufacturer and a remanufacturer at the upper echelon and a retailer at the lower echelon. The retailer faces a constant demand from customers, which is satisfied through recovered and new products received from the remanufacturer and the manufacturer, respectively. The manufacturer produces the product with finite rate, whereas the recovery of returned product is instantaneous at the remanufacturer. We develop three models to determine the optimal production-inventory policy of the players for minimizing the joint total cost of the system. In the first model, the retailer receives the product in batches from the manufacturer and the remanufacture simultaneously, whereas in the second and third models, the batches are received alternatively. In the third model, however, the procurement of raw material at the manufacturer is also considered. Numerical illustration is presented to examine the impact of certain key parameters.