Acetylcholinesterase-polyaniline biosensor investigation of organophosphate pesticides in selected organic solvents

The behavior of an amperometric organic-phase biosensor consisting of a gold electrode modified first with a mercaptobenzothiazole self-assembled monolayer, followed by electropolymerization of polyaniline in which acetylcholinesterase as enzyme was immobilized, has been developed and evaluated for organophosphorous pesticide detection. The voltammetric results have shown that the formal potential shifts anodically as the Au/MBT/PANI/AChE/PVAc thick-film biosensor responded to acetylthiocholine substrate addition under anaerobic conditions in selected organic solvent media containing 2% v/v 0.05 M phosphate buffer, 0.1 M KCl (pH 7.2) solution. Detection limits in the order of 0.147 ppb for diazinon and 0.172 ppb for fenthion in acetone-saline phosphate buffer solution, and 0.180 ppb for diazinon and 0.194 ppb for fenthion in ethanol-saline phosphate buffer solution has been achieved.     

Use of n-fold cross-validation to evaluate three methods to calculate heavy truck annual average daily traffic and vehicle miles traveled

Reliable estimates of heavy-truck volumes in the United States are important in a number of transportation applications including pavement design and management, traffic safety, and traffic operations. Additionally, because heavy vehicles emit pollutants at much higher rates than passenger vehicles, reliable volume estimates are critical to computing accurate inventories of on-road emissions. Accurate baseline inventories are also necessary to forecast future scenarios. The research presented in this paper evaluated three different methods commonly used by transportation agencies to estimate annual average daily traffic (AADT), which is used to determine vehicle miles traveled (VMT). Traffic data from continuous count stations provided by the Iowa Department of Transportation were used to estimate AADT for single-unit and multiunit trucks for rural freeways and rural primary highways using the three methods. The first method developed general expansion factors, which apply to all vehicles. AADT, representing all vehicles, was estimated for short-term counts and was multiplied by statewide average truck volumes for the corresponding roadway type to obtain AADT for each truck category. The second method also developed general expansion factors and AADT estimates. Truck AADT for the second method was calculated by multiplying the general AADT by truck volumes from the short-term counts. The third method developed expansion factors specific to each truck group. AADT estimates for each truck group were estimated from short-term counts using corresponding expansion factors. Accuracy of the three methods was determined by comparing actual AADT from count station data to estimates from the three methods. Accuracy of the three methods was compared using n-fold cross-validation. Mean squared error of prediction was used to estimate the difference between estimated and actual AADT. Prediction error was lowest for the method that developed separate expansion factors for trucks. Implications for emissions estimation using the different methods are also discussed.     

Source apportionment of fine particles in Tennessee using a source-oriented model

Source apportionment of fine particles (PM2.5, particulate matter < 2 microm in aerodynamic diameter) is important to identify the source categories that are responsible for the concentrations observed at a particular receptor. Although receptor models have been used to do source apportionment, they do not fully take into account the chemical reactions (including photochemical reactions) involved in the formation of secondary fine particles. Secondary fine particles are formed from photochemical and other reactions involving precursor gases, such as sulfur dioxide, oxides of nitrogen, ammonia, and volatile organic compounds. This paper presents the results of modeling work aimed at developing a source apportionment of primary and secondary PM2.5. On-road mobile source and point source inventories for the state of Tennessee were estimated and compiled. The national emissions inventory for the year 1999 was used for the other states. U.S. Environmental Protection Agency Models3/Community Multi-Scale Air Quality modeling system was used for the photochemical/secondary particulate matter modeling. The modeling domain consisted of a nested 36-12-4-km domain. The 4-km domain covered the entire state of Tennessee. The episode chosen for the modeling runs was August 29 to September 9, 1999. This paper presents the approach used and the results from the modeling and attempts to quantify the contribution of major source categories, such as the on-road mobile sources (including the fugitive dust component) and coal-fired power plants, to observed PM2.5 concentrations in Tennessee. The results of this work will be helpful in policy issues targeted at designing control strategies to meet the PM2.5 National Ambient Air Quality Standards in Tennessee.     

Numerical simulation of hydrogen–air detonation for damage assessment in realistic accident scenarios

An accidental hydrogen release within an equipment enclosure may result in the presence of detonable mixture in a confined environment. From a safety standpoint, it is then useful to assess the potential for damage. In that context, numerical simulation of the sequence of events subsequent to detonative ignition provides a useful tool, although with obvious limitations. This article describes the procedure, summarizes two case studies, and reviews the limitations. First, a hydrogen dispersion pattern is obtained from numerical simulation of dispersion, using a commercial package designed primarily for incompressible flow. This dispersion cloud is then used as the initial condition in an inviscid, compressible, reactive flow simulation. To force detonative ignition, a sufficiently large amount of energy is deposited in a small region that corresponds to the ignition location. Chemistry is modeled using a single step Arrhenius model. Because the wave thickness is small compared with the computational domain, a fine mesh is needed, limiting the practicality of the process to two-dimensional geometries. This is the most significant limitation; it is conservative. The two cases described in the paper include an electrolyzer, in which a small release occurs, leading potentially to some damage to the enclosure, and a reformer, in which the consequences are potentially more serious.     

“四沿”化工企业污水处理系统安全事故状态下负荷缓冲及安全环境(SE)联锁探讨

在对"四沿"(沿江、沿河、沿湖、沿海)化工行业污水处理方法及流程特点总结的基础上,归纳出应对水力和污染物冲击负荷的缓冲方法。为克服缓冲控制能力有限的缺点,提出一种新方法——SE(安全和环境)联锁,以期达到完善管理、提高控制效果的目的,并详细阐述了该方法在管理及技术层面的实施途径。     

油气集输站安全监控预警及管理信息系统的开发

提出油气集输站安全监控预警及管理信息系统建设的调研内容、需求分析以及安全相关控制系统的风险分析流程。设计了该系统建设的4层结构框架和拓扑图,深入研究了实时参数监控、分级报警与安全保护控制、智能诊断与预警、多媒体监控、安全生产管理信息子系统的主要开发内容和功能实现。     

高墩大跨连续刚构桥施工期安全评价

针对高墩大跨连续刚构桥施工期结构概率失效的特性,提出了基于失效概率的安全评价方法.以徐水沟特大桥为工程背景,通过风险评定识别出施工最不利阶段--最大双悬臂时的主要风险因素即:节段特性模量的不确定性、梁体自重的不确定性以及预应力损失的不确定性.采用大型通用有限元程序ANSYS及蒙特卡洛法,计算徐水沟特大桥在最大悬臂时的失效概率,并确定施工期的目标可靠度.依据高墩大跨连续刚构桥施工期结构概率失效的评价结果,提出相应的风险控制措施.     

基于临水区域化工园区的整体安全研究

针对临水区域化工园区的生产特点及在整体安全方面存在的普遍问题,提出在临水区域化工园区内要进行合理布局,做到功能分区明确;同时需建立园区安全生产管理、监测预警及应急处置系统,主要是由固定危险源和移动危险源动态安全管理子系统、安全生产监测预警系统、突发事故应急处置平台等所组成;坚持安全监控信息化与标准化,对化工园区的整体安全性的提高将发挥巨大的作用,为建设"平安园区"打下坚实的基础。     

Meta‐analytic tests of relationships between organizational justice and citizenship behavior: testing agent‐system and shared‐variance models

Research on the unique effects of different types of perceived fairness on citizenship behavior that benefits individuals (organizational citizenship behavior (OCB‐I) and organizations (OCB‐O) has produced mixed results. We assert that how OCB‐O and OCB‐I are conceptualized affects the patterns of results, and we hypothesize that, when OCB is conceptualized appropriately, an agent‐system model is supported (interactional and procedural justice are the strongest unique predictors of OCB‐I and OCB‐O, respectively). We also hypothesize that shared variance among the justice types explains additional variance in OCB. Analyses of semi‐ partial correlations conducted on meta‐analytic coefficients supported our hypotheses. Theoretical and practical implications are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

三维脚型测量技术及方法的研究

本文阐述了人体脚型的测量方法及特点,比较后得出人工测量与三维扫描测量技术之间的差别。以YETI三维脚型扫描仪为模型,详细分析了脚型扫描仪的结构原理,摸索并提出了简单实用的测量方法,讨论了YETI三维脚型扫描仪获得的原始数据、脚型横截面以及脚型投影图的特点。