Characterization of particulate matter concentrations during controlled indoor activities

Indoor sources have been identified as a major contributor to the increase of particle concentration in indoor environments. The work presented here is a study of the characteristics of particulate matter number size distribution and mass concentration under controlled indoor activities in a laboratory room. The objective is to characterize particulate matter concentrations indoors resulted under the influence of specific sources. Measurements were performed in an empty laboratory (period September–October 2006) using a GRIMM SMPS+C system (particle size range between 11.1 and 1083.3 nm), a DustTrak Aerosol Monitor (TSI) and a P-Trak Ultrafine Particle Counter (TSI). The studied indoor activities included candle burning, hot plate heating, water boiling, onion frying, vacuuming, hair drying, hair spraying, smoking and burning of incense stick. The AMANpsd computer algorithm was used to evaluate the modal structure of measured particle number size distribution data. Furthermore, the change of the particle number size distribution shape under the influence of different emission sources was studied versus time. Finally the particle emission rates were computed. High particle number concentrations were observed during smoking, onion frying, candle burning and incense stick burning. The highest particle mass concentrations were measured during smoking and hair spraying. The shift of the particle size distribution to larger diameters suggests the presence of strong coagulation effect during candle burning, incense stick burning, smoking and onion frying. The size distribution was mainly bimodal during onion frying and candle burning, whereas the size distribution remained unimodal during incense stick burning and smoking experiments.     

International Environmental Agreements: Design of Optimal Transfers Under Heterogeneity

International environmental agreements (IEAs) can coordinate abatement of transboundary pollutants. This paper investigates how heterogeneous countries facing a stock pollutant might structure such an agreement. In particular, we examine how an IEA might be implemented with a set of monetary transfers. The focus is on transfers that are time invariant, linear in emissions, and consistent with budget balance. There is a range of such schemes that would induce efficient emissions. We provide a simple and intuitive characterization of these penalties and describe how specific proposals might be chosen in order to facilitate compliance and implementation. Our proposals are illustrated with a simple example. We show that heterogeneity reduces the scope for penalty schemes to jointly satisfy desirable properties.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

The Plume Volume Molar Ratio Method for Determining NO2/NOx Ratios in Modeling—Part II: Evaluation Studies

ABSTRACT

A previous paper¹ discusses the methodology for a new method for deriving the nitrogen dioxide/nitrogen oxide (NO₂/NO_x) ratio in plumes that originally are composed mainly of (NO_x). It is called the Plume Volume Molar Ratio Method (PVMRM). This paper documents its performance against six different data sets. These performance evaluations show that the PVMRM can realistically predict the NO₂ fraction at close-in receptors yet still provide conservative estimates so that the air quality standards can be protected.     

Photochemical Reactivities of Paraffinic Hydrocarbon-Nitrogen Oxide Mixtures Upon Addition of Propylene or Toluene

Effects associated with photochemical air pollution were measured during irradiation of n-butane-nitrogen oxide or n-butane-ethane-nitrogen oxide mixtures, with small amounts of propylene or toluene added. The effects measured including nitrogen dioxide and oxidant dosages, yields of formaldehyde and peroxy-acetyl nitrate, and eye irritation response. The results obtained clearly show that beneficial effects result from selective changes in hydrocarbon composition as well as from reduction of total hydrocarbon concenfration. Exclusion of olefins and alkylbenzenes was highly effective in reducing oxidant dosage, formaldehyde and peroxyacetyl nitrate concentrations, and eye irritation response. The only penalty was a modest increase in nitrogen dioxide dosage. A large reduction in nitrogen oxide concentration reduced nitrogen dioxide dosage and eye irritation response, but with the penalty of a large increase in oxidant dosage. The desirability of preferentially reducing olefins and alkylbenzenes rather than paraffinic hydrocarbons, acetylene, and benzene is strongly supported by this study. Research and development efforts should be directed toward preferential hydrocarbon control by mechanical or catalytic control     

The Role of Disaggregation of Asset Values in Flood Loss Estimation: A Comparison of Different Modeling Approaches at the Mulde River,Germany

In loss estimation there is a spatial mismatch of hazard data that are commonly modeled on an explicit raster level and exposure data that are often available only for aggregated administrative units. Usually disaggregation methods that use ancillary information to distribute lumped exposure data in a finer spatial resolution help to bridge this gap. However, the actual influence of different mapping techniques and ancillary data on the final loss estimation has not been analyzed yet. In this paper three methods are applied to disaggregate residential building assets using two kinds of land use/land cover (LULC) data. The resulting disaggregated assets are validated and compared using census data of the residential building number on the community and constituency level. In addition, the disaggregated assets are taken to estimate residential building losses due to the flood in August 2002 in 21 municipalities on the River Mulde in Saxony, Germany. Losses are calculated with the help of four loss models. In general, disaggregation helps to decrease the error variance within the loss estimation. It must, however, be stated that the application of sophisticated disaggregation methods does not lead to significant improvements compared to the straightforward binary method. Therefore more effort should instead be put into the provision of high-resolution LULC data. Finally, the remaining uncertainties in loss estimation are high and demand further improvements in all modeling aspects.     

The importance of monitoring and evaluation in adaptive maritime spatial planning

Adaptive maritime spatial planning (MSP) uses monitoring and evaluation of the effectiveness of spatial and temporal management measures to promote understanding and improve planning and decision-making. An adaptive approach to MSP involves exploring alternative ways to meet management objectives, predicting the outcomes of alternative management measures, implementing one or more of these alternative management measures, monitoring to learn about the effects of management measures, and then using the results to update knowledge and adjust management actions. A monitoring and evaluation plan should be designed to be both cost effective and comprehensive. The process of setting and assessing performance metrics requires that the ecological and socio-economic objectives of the spatial management plan must be clearly stated up front for management actions to reflect those objectives accurately. To evaluate the effectiveness of a MSP plan, a range of ecological, socio-economic and institutional indicators need to be developed and monitored.