Revised relative potency values for PCDDs, PCDFs, and non-ortho-substituted PCBs for the optimized H4IIE-luc in vitro bioassay

While the World Health Organization 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) equivalency factors are useful estimates of relative potencies of mixtures when conducting risk assessments, they are not useful when comparing the results of bioassays such as the H4IIE-luc to concentrations of TCDD equivalents calculated from instrumental analyses. Since there are thousands of dioxin-like compounds (DLCs), one use of screening assays is to determine if all of the aryl hydrocarbon receptor (AhR) active DLCs in a mixture have been accounted for in instrumental analyses. For this purpose, bioassay-specific relative potency (ReP) values are needed. RePs of 21 polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and dioxin-like polychlorinated biphenyls that exhibit effects mediated through the AhR were determined by use of the H4IIE-luc assay. Different values of RePs are derived, depending on the statistical, curve-fitting methods used to derive them from the dose–response relationships. Here, we discuss the various methods for deriving RePs from in vitro data and their assumptions and effects on values of RePs. Full dose–response curves of 2,3,7,8-TCDD and other representative DLCs were used to estimate effective concentrations at multiple points (e.g., EC20-50-80), which were then used to estimate ReP of each DLC to 2,3,7,8-TCDD.     

Extreme Values in TSP Distribution Functions

The highest values in annual TSP distributions fall below the best-fit, log-normal straight line more than one would expect from ordinary sampling statistics but not dramatically so. The lowest values in annual TSP distributions overwhelmingly fall below the best-fit, log-normal straight line. The most highly improbable high values above the best-fit line in such distributions are very questionable and probably do not represent true air quality values. The most improbable cases of highest values falling below the best-fit, log-normal line are the result of data artifacts at the opposite end of the data distribution. They do not represent low probabilities and probably do represent true air quality values. The most improbable low values are all of highly doubtful validity.     

Destruction of Bacteria and Toxic Organic Chemicals by a Corona Discharge

A detailed analysis of international trends in air pollution control and waste management markets forecasts considerable growth and expansion due to increased economic activity, more stringent regulations requiring pollution control, and the increased amounts of solid waste being generated worldwide.     

Potential Problems with the Current RCRA Incineration Permit Process

The current hazardous waste incinerator permitting process is highly uncertain, complex, and unnecessarily restrictive, which makes a permitted facility very difficult to operate on a continuous basis without permit violations. This paper discusses the problems in the current regulation and enforcement practices. Some solutions are suggested. It is suggested that the current highly conservative permitting approach of disallowing any operating conditions or banning any waste feeds which the permit writer may have the slightest doubt of failing to meet the four-9s destruction and removal efficiency (DRE) requirement for even a few seconds, should be reevaluated. It is suggested that a more reasonable approach, using practical engineering judgment to allow those operating conditions and waste feeds which should be able to meet the DRE requirement, should be considered by the regulatory agencies.     

Removal of Low Concentrations of Carbon Tetrachloride in Compost-Based Biofilters Operated under Methanogenic Conditions

ABSTRACT

Research was performed to demonstrate the removal of carbon tetrachloride (CT) using compost biofilters operated under methanogenic conditions. Biofilters were operated at an empty-bed residence time of 2.8 minutes using nitrogen as the atmosphere. Hydrogen and carbon dioxide were supplied as an electron donor and carbon source, respectively, during acclimation of the bed medium microbes. Once methanogenesis was demonstrated, CT flow to the biofilter was established. Biofilters were operated over a CT concentration range from 20 to 700 ppbv for 6 months. Bed medium microbes were able to remove up to 75% of the inlet CT. At excessively high CT concentrations (>500 ppmv), methane production and hydrogen utilization by the bed medium microbes appeared to be inhibited. CT removal by the biofilter decreased when the hydrogen supply was removed from the biofilter inlet, indicating that hydrogen acted as the electron donor for reductive dechlorination. The removal efficiency and relatively low empty bed residence times demonstrated by these laboratory-scale biofilters indicate that anaerobic biofiltration of CT may be a feasible full-scale process.     

Water Transformation in the Media of Biofilters Controlled by Rhodococcus fascians in Treating an Ethyl Acetate-Contaminated Airstream

Abstract

Biofilters do not provide much water for bacteria to grow. To use them efficiently and properly, it is essential to understand the kinetics of water transformation and to control moisture levels. This study aims to clarify whether the metabolism of microorganisms will improve the water-holding capacity of media or will intensify drying. This experiment was conducted in duplicate, that is, both with and without bacterial inoculation. Both the constant water content mode and the declining water content mode show that microbial growth in a log phase will enhance drying. In contrast, the bacteria growing in a logarithmic decline phase will improve water-holding capacity. Basically, water evaporation can result from the latent heat obtained from microbial respiration or from the physical temperature difference between the unsaturated air and the wet media. Two ways that biofilters can gain water are from water incorporated into bacteria cells and from water obtained from the oxidation of volatile organic compounds (VOCs).     

Abatement of Sulfur Hexafluoride Emissions from the Semiconductor Manufacturing Process by Atmospheric-Pressure Plasmas

Abstract

Sulfur hexafluoride (SF₆) is an important gas for plasma etching processes in the semiconductor industry. SF₆ intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF₆ abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes—dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)—were employed and evaluated. Experimental results indicated that as much as 91% of SF₆ was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF₆, 12% oxygen (O₂), and 40% argon (Ar), with nitrogen (N₂) as the carrier gas. Four additives, including Ar, O₂, ethylene (C₂H₄), and H₂O_(g), are effective in enhancing SF₆ abatement in the range of conditions studied. DBD achieves a higher SF₆ removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF₆ is mainly converted to SOF₂,SO₂F₄, sulfur dioxide (SO₂), oxygen difluoride (OF₂), and fluoride (F₂). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF₆ emissions.     

Characterization of Polycyclic Aromatic Hydrocarbons from the

Abstract

Diesel fuels governed by U.S. regulations are based on the index of the total aromatic contents. Three diesel fuels, containing various fractions of light cycle oil (LCO) and various sulfur, total polyaromatic, and total aromatic contents, were used in a heavy-duty diesel engine (HDDE) under transient cycle test to assess the feasibility of using current indices in managing the emissions of polycyclic aromatic hydrocarbons (PAHs) from HDDE. The mean sulfur content in LCO is 20.8 times as much as that of premium diesel fuel (PDF). The mean total polyaromatic content in LCO is 28.7 times as much as that of PDF, and the mean total aromatic content in LCO is 2.53 times as much as that of PDF. The total polyaromatic hydrocarbon emission factors in the exhaust from the diesel engine, as determined using PDF L3.5 (3.5% LCO and 96.5% PDF), L7.5 (7.5% LCO and 92.5% PDF), and L15 (15% LCO and 85% PDF) were 14.3, 25.8, 44, and 101 mg L^?1, respectively. The total benzo(a)pyrene equivalent (BaP_eq) emission factors in the exhaust from PDF, L3.5, L7.5, and L15 were 0.0402, 0.121, 0.219, and 0.548 mg L^?1, respectively. Results indicated that using L3.5 instead of PDF will result in an 80.4% and a 201% increase of emission for total PAHs and total BaP_eq, respectively. The relationships between the total polyaromatic hydrocarbon emission factor and the two emission control indices, including fuel polyaromatic content and fuel aromatic content, suggest that both indices could be used feasibly to regulate total PAH emissions. These results strongly suggest that LCO used in the traveling diesel vehicles significantly influences PAH emissions.     

Emission Factors of Air Toxics from Semiconductor Manufacturing in Korea

Abstract

The development of local, accurate emission factors is very important for the estimation of reliable national emissions and air quality management. For that, this study is performed for pollutants released to the atmosphere with source-specific emission tests from the semiconductor manufacturing industry. The semiconductor manufacturing industry is one of the major sources of air toxics or hazardous air pollutants (HAPs); thus, understanding the emission characteristics of the emission source is a very important factor in the development of a control strategy. However, in Korea, there is a general lack of information available on air emissions from the semiconductor industry. The major emission sources of air toxics examined from the semiconductor manufacturing industry were wet chemical stations, coating applications, gaseous operations, photolithography, and miscellaneous devices in the wafer fabrication and semiconductor packaging processes. In this study, analyses of emission characteristics, and the estimations of emission data and factors for air toxics, such as acids, bases, heavy metals, and volatile organic compounds from the semiconductor manufacturing process have been performed. The concentration of hydrogen chloride from the packaging process was the highest among all of the processes. In addition, the emission factor of total volatile organic compounds (TVOCs) for the packaging process was higher than that of the wafer fabrication process. Emission factors estimated in this study were compared with those of Taiwan for evaluation, and they were found to be of similar level in the case of TVOCs and fluorine compounds.     

Investigation of Selective Catalytic Reduction Impact on Mercury Speciation under Simulated NOx Emission Control Conditions

Abstract

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NO_x) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NO_x reduction, promote the formation of oxidized mercury (Hg²⁺).

The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg⁰) oxidation. Bench-scale experiments were conducted to investigate Hg⁰ oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO₂) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO₂ in the flue gases on Hg⁰ oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg⁰ to Hg²⁺ under SCR reaction conditions. The importance of HCl for Hg⁰ oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg⁰ oxidation occurring across the SCR reactors in the field.