Differences and similarities of gas and dust explosions: A critical evaluation of the European ‘ATEX’ directives in relation to dusts

Explosive gas mixtures and explosive dust clouds, once existing, exhibit similar ignition and combustion features. However, there are two basic differences between dusts and gases which are of substantially greater significance in design of safety standards than these similarities. Firstly, the physics of generation and up-keeping of dust clouds and premixed gas/vapour clouds are substantially different. This means that in most situations where accidental explosive gas clouds may be produced quite readily, generation of explosive dust clouds would be highly unlikely. Secondly, contrary to premixed gas flame propagation, the propagation of flames in dust/air mixtures is not limited only to the flammable dust concentration range of dynamic clouds. The state of stagnant layers/deposits offers an additional discrete possibility of flame propagation.

The two European Directives 94/9/EC (1994) and 1999/92/EC (1999) primarily address gases/vapours, whereas the particular properties of dusts are not addressed adequately. Some recent IEC and European dust standards resulting from this deficiency are discussed, and the need for revising the two directives accordingly is emphasized.     

Off-site emergency scenario, a case study from a LPG Bottling Plant

After Bhopal disaster, emergency planning in an industrial area has become inevitable. The off-site emergency plan is an integral part of any major hazard control system. Boiling Liquid Expanding Vapour Explosion (BLEVE) leads to fatal consequences. This paper highlights some salient features of the emergency scenario, which ultimately leads to fireball with enormous pressure wave all around.     

Experimental Verification of the Computerized Method for Work Space Optimization in Conditions of Static Work

The aim of this study was to verify a theoretical model for upper extremity work space optimization. In order to do that, experimental studies were conducted in which two parameters of the electromyography (EMG) signal were analyzed: AMP (amplitude calculated as Root Mean Square) and SZC (coefficient of the slope of the regression line between time and Zero Crossing values). Values of forces in muscles (parameter MOD) were calculated from theoretical studies. A comparison of experimental (AMP, SZC) and theoretical (MOD) parameters was performed by analyzing the coefficient of correlation between those parameters and differentiation of muscular load according to external load value. Analysis showed that the theoretical and experimental results are in step, which means that the developed model can be used for upper extremity work space optimization.     

Physical Effects of New Devices for Bricklayers

Bricklaying is a physically demanding job. Bricklayers frequently flex their trunk to pick up bricks and mortar and position these in a wall. The experienced workload is highest working with bricks at 0 to 50 cm from the floor. In this study the effects of 2 devices that have proven to be feasible in practice are evaluated.

The 50 cm raise due to the 2 devices is experienced as comfortable, the estimated lumbar compression force was reduced, and observations indicate likewise. It is discussed that the field experiments have many drawbacks. Nevertheless, based on this study in combination with other literature the improvements could be recommended.     

Driver Workload Response to In-Vehicle Device Operations

A central concern of Intelligent Transportation Systems (ITS) is the effect of in-vehicle devices (e.g., cell phones, navigation systems, radios, etc.) on driver performance and safety. As diverse and innovative technologies are designed and implemented for in-vehicle use, questions regarding the presence and use of these devices assume progressively greater importance. Further concerns for advanced driver training require us to develop and validate reliable and effective procedures for assessing such effects. This work examines a number of candidate procedures, in particular the evaluation of change in cognitive workload as a strategy by which such goals might be achieved.     

A Study of Computer-Based Task Performance Under Thermal Stress

A visual-visual dual computer task was designed to test the effect of the thermal environment on dual task performance. The temperatures selected for testing were 20 and 35 °C Wet Bulb Globe Temperature (WBGT). 34 volunteers were randomly assigned to 1 of the 2 temperature conditions. Individual differences in single task performance were controlled by equating the baselines of single task performance. Once individual differences in single task capacity were controlled, statistically significant differences in performance were demonstrated. Mean accuracy was computed over a 1-hr testing period in each temperature condition. Participants’ mean accuracy in the 35° condition (38.18%) was substantially lower than in the 20° condition (50.88%).     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.     

Experimental investigation of hydrogen–air deflagrations and detonations in semi-confined flat layers

This paper presents results of an experimental investigation on the deflagration and deflagration-to-detonation transition (DDT) in an obstructed (blockage ratio BR = 50%), semi-confined flat layer filled with uniform hydrogen–air mixtures. The effect of mixture reactivity depending on flat layer thickness and its width is studied to evaluate the critical conditions for sonic flame propagation and the possibility for detonation onset. The experiments were performed in a transparent, rectangular channel with a length of 2.5 m. The flat layer thickness was varied from 0.06 to 0.24 m and the experiments were performed for different channel widths of 0.3, 0.6 and 0.9 m. The experimental results show flame velocity vs. hydrogen concentration for different thicknesses and widths of the semi-confined flat layer. Three different flame propagation regimes were observed: slow subsonic flame (M << 1), sonic deflagration (M ～ 1) and detonation (M >> 1). It is shown that flame acceleration (FA) to sonic speed is independent of the width of the flat layer. The critical expansion ratio for effective flame acceleration to sonic speed was found to be linearly dependent on the reciprocal layer thickness.     

Assessment of an accidental vapour cloud explosion: Lessons from the Indian Oil Corporation Ltd. accident at Jaipur,India

On 29 October 2009, at 19:30 IST, a devastating vapour cloud explosion occurred in a large fuel storage area at the Indian Oil Corporation (IOC) Depot in Jaipur, India, generating significant blast pressure. As a consequence of this explosion, the entire installation was destroyed, buildings in the immediate vicinity were heavily damaged, and windowpane breakages were found up to 2 km from the terminal. The IOC estimated that the total loss from the fire and explosion was approximately INR 2800 million.Ironically, as a storage site, the Jaipur terminal was not highly congested, and thus was not considered to have adequate potential for a vapour cloud explosion (VCE). Nevertheless, the prima facie evidences indicate that this was a case of VCE. Therefore, the main objective of this study is to quantify the potential overpressures due to vapour cloud explosions (VCEs) using the Process Hazard Analysis DNV Norway based PHAST 6.51 Software. The results are validated by the extent of the damage that had occurred. The estimation of the VCE shows that a maximum 1.0 bar overpressure was generated in the surrounding area. The initial assessment of the accident data roughly estimates the release mode, time, and amount of vaporized fuel. A more accurate estimate has been obtained by modelling the dispersion of vapour clouds in the surrounding atmosphere, which reveals trends and relationships for the occurrence of vapour cloud explosions.