Material and energy recovery in integrated waste management systems: project overview and main results

This paper describes the context, the basic assumptions and the main findings of a joint research project aimed at identifying the optimal breakdown between material recovery and energy recovery from municipal solid waste (MSW) in the framework of integrated waste management systems (IWMS). The project was carried out from 2007 to 2009 by five research groups at Politecnico di Milano, the Universities of Bologna and Trento, and the Bocconi University (Milan), with funding from the Italian Ministry of Education, University and Research (MIUR). Since the optimization of IWMSs by analytical methods is practically impossible, the search for the most attractive strategy was carried out by comparing a number of relevant recovery paths from the point of view of mass and energy flows, technological features, environmental impact and economics. The main focus has been on mature processes applicable to MSW in Italy and Europe. Results show that, contrary to a rather widespread opinion, increasing the source separation level (SSL) has a very marginal effects on energy efficiency. What does generate very significant variations in energy efficiency is scale, i.e. the size of the waste-to-energy (WTE) plant. The mere value of SSL is inadequate to qualify the recovery system. The energy and environmental outcome of recovery depends not only on "how much" source separation is carried out, but rather on "how" a given SSL is reached.     

Precision determination for the dynamic respirometric index (DRI) method used for biological stability evaluation on municipal solid waste and derived products

Dynamic respiration index (DRI) is an effective respirometric method to measure the biological stability of municipal solid waste (MSW). It allows testing MSW biological stability under standardized conditions and is now used as a routine analytical method. However, the method needs to be studied for precision parameters to ensure the quality of results generated.This work reports on a DRI validation study, detecting repeatability (r) and reproducibility limits (R). To perform the study, 4-6 Italian laboratories took part in an interlaboratory test for the validation of the DRI method on four different municipal solid wastes from different mechanical-biological treatment full-scale plants. Precision values (r and R) of DRI, expressed as relative standard deviation, were in the range of 3.6% and 15.5%, and were acceptable when compared with previous data obtained in another respirometric test. On the other hand, no regressions were found between r and R, and DRI, and as a consequence prediction of precision values was not possible a priori for different DRI levels, unless the same typology of waste was considered.     

The evaluation of stability during the composting of different starting materials: comparison of chemical and biological parameters

Three blends formed by: (i) food processing waste (CP(FP)), (ii) waste water sewage sludge (CP(WW)), and (iii) their mixture (CP(FP+WW)), blended with tree pruning as bulking agent, were composted over 3 months. During composting the blends were monitored for the main physical-chemical characteristics: temperature, oxygen saturation level (O(2)%), pH, total and volatile solids, total organic carbon, and organic nitrogen (N(org)). In addition to the main parameters, the dissolved organic carbon (DOC), the inorganic nitrogen and the Oxygen Uptake Rate (OUR) were monitored. All the mixtures easily reached a peak temperature around 70°C, related to the lowest O(2)%. After 90 d, CP(FP), CP(FP+WW), and CP(WW) showed an organic matter mineralization of 43%, 35% and 33%, respectively; CP(FP) fitted an exponential model while both CP(FP+WW), and CP(WW) fitted a logistic model. During composting an OUR reduction of 79%, 78% and 73% was registered in CP(FP), CP(FP+WW), and CP(WW), respectively; the OUR successfully fitted the adopted exponential model and well reflected the stabilization process in time. The N(org) recovery at the end of the process was positive only in CP(WW) (11.6%). The DOC significantly decreased during the composting process but did not successfully fit any model. The mineral nitrogen did not follow the typical pattern with NH(4)(+) disappearance and NO(3)(-) accumulation. Strong NO(3)(-) losses were evident in all blends, while NH(4)(+) accumulations were detectable only in CP(FP), and CP(FP+WW). The NH(4)(+)/NO(3)(-) ratio did not satisfactorily reflect the composting process over time. The comparison of the first order (exponential) and logistic (sigmoidal) models applied to the OUR and OM course highlights the role of mineral nitrogen as limiting factor during composting of the more stabilized sludge.     

Assessing the impact of Cross Compliance measures on nitrogen fluxes from European farmlands with DNDC-EUROPE

We investigated the effects of the agricultural Cross Compliance measures for European cultivated lands, focusing on nitrogen (N) fluxes from corn fields. Four scenarios have been designed according to some conservation farming practices, namely no-till, max manure, catch crop and N splitting. Results indicated that (1) in the no-till scenario the N₂O fluxes are decreased during the first simulated years, with a return to default fluxes in following years; no-till particularly decreased N₂O emission in the dryer and colder simulation spatial units (HSMUs); (2) the no-till and the N splitting scenarios slightly increased the N surplus because of a decrease in plant uptake; (3) introducing a rotation with alfalfa decreased the N leaching in the corn crops following the catch crops; and (4) the application of fertilizer and manure during the cold and wet seasons led to an increase of N leaching.     

Validating a nondestructive optical method for apportioning colored particulate matter into black carbon and additional components

Exposure of black carbon (BC) is associated with a variety of adverse health outcomes. A number of optical methods for estimating BC on Teflon filters have been adopted but most assume all light absorption is due to BC while other sources of colored particulate matter exist. Recently, a four-wavelength-optical reflectance measurement for distinguishing second hand cigarette smoke (SHS) from soot-BC was developed (Brook et al., 2010; Lawless et al., 2004). However, the method has not been validated for soot-BC nor SHS and little work has been done to look at the methodological issues of the optical reflectance measurements for samples that could have SHS, BC, and other colored particles. We refined this method using a lab-modified integrating sphere with absorption measured continuously from 350 nm to 1000 nm. Furthermore, we characterized the absorption spectrum of additional components of particulate matter (PM) on PM(2.5) filters including ammonium sulfate, hematite, goethite, and magnetite. Finally, we validate this method for BC by comparison to other standard methods. Use of synthesized data indicates that it is important to optimize the choice of wavelengths to minimize computational errors as additional components (more than 2) are added to the apportionment model of colored components. We found that substantial errors are introduced when using 4 wavelengths suggested by Lawless et al. to quantify four substances, while an optimized choice of wavelengths can reduce model-derived error from over 10% to less than 2%. For environmental samples, the method was sensitive for estimating airborne levels of BC and SHS, but not mass loadings of iron oxides and sulfate. Duplicate samples collected in NYC show high reproducibility (points consistent with a 1:1 line, R(2) = 0.95). BC data measured by this method were consistent with those measured by other optical methods, including Aethalometer and Smoke-stain Reflectometer (SSR); although the SSR looses sensitivity at filter loadings above 90 ng/mm(2). Furthermore, positive correlations (R(2) = 0.7) were observed between EC measured by NIOSH Method 5040 on quartz filters and BC measured in co-located Teflon filter samples collected from both heating and non-heating seasons. Overall, the validation data demonstrates the usefulness of this method to evaluate BC from archived Teflon filters while potentially providing additional component information.     

Air pollution perception in ten countries during the COVID-19 pandemic

As largely documented in the literature, the stark restrictions enforced worldwide in 2020 to curb the COVID-19 pandemic also curtailed the production of air pollutants to some extent. This study investigates the perception of the air pollution as assessed by individuals located in ten countries: Australia, Brazil, China, Ghana, India, Iran, Italy, Norway, South Africa and the USA. The perceptions towards air quality were evaluated by employing an online survey administered in May 2020. Participants (N = 9394) in the ten countries expressed their opinions according to a Likert-scale response. A reduction in pollutant concentration was clearly perceived, albeit to a different extent, by all populations. The survey participants located in India and Italy perceived the largest drop in the air pollution concentration; conversely, the smallest variation was perceived among Chinese and Norwegian respondents. Among all the demographic indicators considered, only gender proved to be statistically significant.Supplementary InformationThe online version contains supplementary material available at 10.1007/s13280-021-01574-2.     

Evaluating urban PM10 pollution benefit induced by street cleaning activities

Despite their burden in urban particulate air pollution, road traffic non-exhaust emissions are often uncontrolled and information about the effectiveness of mitigation measures on paved roads is still scarce. The present study is aimed to evaluate the effectiveness of mechanical sweeping/water flushing treatments in mitigating urban road dust resuspension and to quantify the real benefit in terms of ambient PM₁₀ concentrations. To this aim a specific campaign was carried out in a heavily trafficked central road of Barcelona (Spain), a Mediterranean city suffering from a traffic-related pollution, both for a high car density and a frequent lack of precipitation. Several street washings were performed by means of mechanical sweepers and pressure water during night in all traffic lanes and sidewalks. PM₁₀ levels were simultaneously compared with four reference urban background air quality stations to interpret any meteorological variability. At the downwind measurement site, PM₁₀ concentrations registered a mean daily decrease of 8.8 μg m^?3 during the 24 h after street washing treatments. However 3.7–4.9 μg m^?3 of such decrease were due to the meteorological variability detected at the upwind site, as well as at two of the reference sites. This reveals that an effective decrease of 4–5 μg m^?3 (7–10%) can be related to street washing efficiency. Mitigation of road dust resuspension was confirmed by investigating the chemical composition of airborne-PM₁₀ filters. Concentrations of Cu, Sb, Fe and mineral matter decrease significantly with respect to concentrations of elemental carbon, used as tracer for exhaust diesel emissions. High efficiency of street washing in reducing road dust loads was found by performing periodic samplings both on the treated and the untreated areas.     

Resource Consumption and Environmental Impacts of the Agrofood Sector: Life Cycle Assessment of Italian Citrus-Based Products

Food production and consumption cause significant environmental burdens during the product life cycles. As a result of intensive development and the changing social attitudes and behaviors in the last century, the agrofood sector is the highest resource consumer after housing in the EU. This paper is part of an effort to estimate environmental impacts associated with life cycles of the agrofood chain, such as primary energy consumption, water exploitation, and global warming. Life cycle assessment is used to investigate the production of the following citrus-based products in Italy: essential oil, natural juice, and concentrated juice from oranges and lemons. The related process flowcharts, the relevant mass and energy flows, and the key environmental issues are identified for each product. This paper represents one of the first studies on the environmental impacts from cradle to gate for citrus products in order to suggest feasible strategies and actions to improve their environmental performance.

Organic–Inorganic Hybrid Coatings for the Modification of Barrier Properties of Poly(lactic acid) Films for Food Packaging Applications

Organic–inorganic hybrid coatings based on poly(ε-caprolactone), poly(ethylene oxide) or poly(lactic acid) as organic phase and silica from tetraethoxysilane as inorganic phase were prepared by the sol–gel approach. Coatings were applied onto poly(lactic acid) films for food packaging in order to improve its barrier properties towards oxygen and water vapour. All the prepared coatings were dense, homogeneous layers characterized by a good adhesion to the substrate. The permeance of the coating layers resulted one order of magnitude lower than that of the uncoated poly(lactic acid) (PLA) film. The hydrophilic character of the coating did not permit to gain a significant decrease in the water vapour permeance. The perfect visual transparency of the coatings allows their application without worsening of the esthetical properties of the substrate PLA film.