Bioefficacy evaluation of controlled release formulations based on amphiphilic nano-polymer of carbofuran against Meloidogyne incognita infecting tomato

In the present investigation, the bioefficacy of developed carbofuran formulations, with PEG-600 (7a, CP1) & PEG-900 (7b, CP2) @ 5, 10 and 20 ppm, along with commercial formulation of carbofuran 3G (CP0) were evaluated against the root-knot nematode, Meloidogyne incognita infecting tomato (cv. Pusa Ruby) in pot and field conditions. The bioefficacy data indicated that the formulations developed by utilizing polymers having PEG - 900 (7b) as hydrophilic segment were effective even at 14 days post inoculation (dpi) as evident from shoot and root length. Also, the reduction in penetration was found to be maximum with CP2 (3.6 - 4.6 J2s) at all concentrations compared to CP1 (6.6-16.4 J2s) and CP0 (29.3-32.6 J2s). Overall, CP2 was more effective in reducing the number of nematodes up to 14 days, compared to CP1 and CP0. Both the CR formulations (CP1 and CP2) in general significantly reduced the number of galls, when compared to CP0. However, under field conditions, lower concentrations (5, and 10 ppm) of CP2, were less effective in controlling the gall formation whereas, CP2 at 20 ppm, was most effective than other treatments. The study revealed that the developed CR formulations of carbofuran have the potential for effective management of M. incognita in tomato under field conditions.     

Continuous measurement of peroxyacetyl nitrate (PAN) in suburban and remote areas of western China

Knowledge on atmospheric abundance of peroxyacetyl nitrate (PAN) is important in assessing the severity of photochemical pollution, and for understanding chemical transformation of reactive odd nitrogen and its impact on the budget of tropospheric ozone (O₃). In summer 2006, continuous measurements of PAN were made using an automatic GC–ECD analyzer with an on-line calibrator at a suburban site of Lanzhou (LZ) and a remote site of Mt. Waliguan (WLG) in western China, with concurrent measurements of O₃, total reactive nitrogen (NO_y) and carbon monoxide (CO). At LZ, several photochemical episodes were observed during the study, and the average mixing ratio of PAN (plus or minus standard deviation) was 0.76 (±0.89) ppbv with the maximum value of 9.13 ppbv, compared to an average value of 0.44 (±0.16) ppbv at remote WLG. The PAN mixing ratios in LZ exhibited strong diurnal variations with a maximum at noon, while enhanced concentrations of PAN were observed in the evening and a minimum in the afternoon at WLG. The daily O₃ and PAN concentration maxima showed a strong correlation (r² = 0.91) in LZ, with a regression slope (PAN/O₃) of 0.091 ppbv ppbv^?1. At WLG, six well-identified pollution plumes (lasting 2–8 h) were observed with elevated concentrations of PAN (and other trace gases), and analysis of backward particle release simulation shows that the high-PAN events at WLG were mostly associated with the transport of air masses that had passed over LZ.     

Characterization of on-road vehicle emission factors and microenvironmental air quality in Beijing,China

In this paper, we report the results and analysis of a recent field campaign in August 2007 investigating the impacts of emissions from transportation on air quality and community concentrations in Beijing, China. We conducted measurements in three different environments, on-road, roadside and ambient. The carbon monoxide, black carbon and ultrafine particle number emission factors for on-road light-duty vehicles are derived to be 95 g kg^?1-fuel, 0.3 g kg^?1-fuel and 1.8 × 10¹⁵ particles kg^?1-fuel, respectively. The emission factors for on-road heavy-duty vehicles are 50 g kg^?1-fuel, 1.3 g kg^?1-fuel and 1.1 × 10¹⁶ particles kg^?1-fuel, respectively. The carbon monoxide emission factors from this study agree with those derived from remote sensing and on-board vehicle emission testing systems in China. The on-road black carbon and particle number emission factors for Chinese vehicles are reported for the first time in the literature. Strong traffic impacts can be observed from the concentrations measured in these different environments. Most clear is a reflection of diesel truck traffic activity in black carbon concentrations. The comparison of the particle size distributions measured at the three environments suggests that the traffic is a major source of ultrafine particles. A four-day traffic control experiment conducted by the Beijing Government as a pilot to test the effectiveness of proposed controls was found to be effective in reducing extreme concentrations that occurred at both on-road and ambient environments.     

A validated 2-D diffusion–advection model for prediction of drift from ground boom sprayers

Correct field drift prediction is a key element in environmental risk assessment of spraying applications. A reduced order drift prediction model based on the diffusion–advection equation is presented. It allows fast assessment of the drift potential of specific ground boom applications under specific environmental wind conditions that obey the logarithmic wind profile. The model was calibrated based on simulations with a validated Computational Fluid Dynamics (CFD) model. Validation of both models against 38 carefully conducted field experiments is successfully performed for distances up to 20 m from the field edge, for spraying on flat pasture land. The reduced order model succeeded in correct drift predictions for different nozzle types, wind velocities, boom heights and spray pressures. It used 4 parameters representing the physical aspects of the drift cloud; the height of the cloud at the field edge, the mass flux crossing the field edge, the settling velocity of the droplets and the turbulence. For the parameter set and range considered, it is demonstrated for the first time that the effect of the droplet diameter distribution of the different nozzle types on the amount of deposition spray drift can be evaluated by a single parameter, i.e., the volume fraction of droplets with a diameter smaller than 191 μm. The reduced order model can be solved more than 4 orders of magnitude faster than the comprehensive CFD model.     

A study of the total atmospheric sulfur dioxide load using ground-based measurements and the satellite derived Sulfur Dioxide Index

We present characteristics of the sulfur dioxide (SO₂) loading over Thessaloniki, Greece, and seven other selected sites around the world using SO₂ total column measurements from Brewer spectrophotometers together with satellite estimates of the Version 8 TOMS Sulfur Dioxide Index (SOI) over the same locations, retrieved from Nimbus 7 TOMS (1979–1993), Earth Probe TOMS (1996–2003) and OMI/Aura (2004–2006). Traditionally, the SOI has been used to quantify the SO₂ quantities emitted during great volcanic eruptions. Here, we investigate whether the SOI can give an indication of the total SO₂ load for areas and periods away from eruptive volcanic activity by studying its relative changes as a correlative measure to the SO₂ total column. We examined time series from Thessaloniki and another seven urban and non-urban stations, five in the European Union (Arosa, De Bilt, Hohenpeissenberg, Madrid, Rome) and two in India (Kodaikanal, New Delhi). Based on the Brewer data, Thessaloniki shows high SO₂ total columns for a European Union city but values are still low if compared to highly affected regions like those in India. For the time period 1983–2006 the SO₂ levels above Thessaloniki have generally decreased with a rate of 0.028 Dobson Units (DU) per annum, presumably due to the European Union's strict sulfur control policies. The seasonal variability of the SO₂ total column exhibits a double peak structure with two maxima, one during winter and the second during summer. The winter peak can be attributed to central heating while the summer peak is due to synoptic transport from sources west of the city and sources in the north of Greece. A moderate correlation was found between the seasonal levels of Brewer total SO₂ and SOI for Thessaloniki, Greece (R = 0.710–0.763) and Madrid, Spain (R = 0.691) which shows that under specific conditions the SOI might act as an indicator of the SO₂ total load.     

Adaptation of a speciation sampling cartridge for measuring ammonia flux from cattle feedlots using relaxed eddy accumulation

Improved measurements of ammonia losses from cattle feedlots are needed to quantify the national NH₃ emissions inventory and evaluate management techniques for reducing emissions. Speciation cartridges composed of glass honeycomb denuders and filter packs were adapted to measure gaseous NH₃ and aerosol NH₄⁺ fluxes using relaxed eddy accumulation (REA). Laboratory testing showed that a cartridge equipped with four honeycomb denuders had a total capture capacity of 1800 μg of NH₃. In the field, a pair of cartridges was deployed adjacent to a sonic anemometer and an open-path gas analyzer on a mobile tower. High-speed valves were attached to the inlets of the cartridges and controlled by a datalogger so that up- and down-moving eddies were independently sampled based on direction of the vertical wind speed and a user-defined deadband. Air flowed continuously through the cartridges even when not sampling by means of a recirculating air handling system. Eddy covariance measurement of CO₂ and H₂O, as measured by the sonic and open-path gas analyzer, were used to determine the relaxation factor needed to compute REA-based fluxes. The REA system was field tested at the Beef Research Unit at Kansas State University in the summer and fall of 2007. Daytime NH₃ emissions ranged between 68 and 127 μg m^?2 s^?1; fluxes tended to follow a diurnal pattern correlated with latent heat flux. Daily fluxes of NH₃ were between 2.5 and 4.7 g m^?2 d^?1 and on average represented 38% of fed nitrogen. Aerosol NH₄⁺ fluxes were negligible compared with NH₃ emissions. An REA system designed around the high-capacity speciation cartridges can be used to measure NH₃ fluxes from cattle feedlots and other strong sources. The system could be adapted to measure fluxes of other gases and aerosols.     

Rapid measurement of emissions from military aircraft turbine engines by downstream extractive sampling of aircraft on the ground: Results for C-130 and F-15 aircraft

Aircraft emissions affect air quality on scales from local to global. More than 20% of the jet fuel used in the U.S. is consumed by military aircraft, and emissions from this source are facing increasingly stringent environmental regulations, so improved methods for quickly and accurately determining emissions from existing and new engines are needed. This paper reports results of a study to advance the methods used for detailed characterization of military aircraft emissions, and provides emission factors for two aircraft: the F-15 fighter and the C-130 cargo plane. The measurements involved outdoor ground-level sampling downstream behind operational military aircraft. This permits rapid change-out of the aircraft so that engines can be tested quickly on operational aircraft. Measurements were made at throttle settings from idle to afterburner using a simple extractive probe in the dilute exhaust. Emission factors determined using this approach agree very well with those from the traditional method of extractive sampling at the exhaust exit. Emission factors are reported for CO₂, CO, NO, NO_x, and more than 60 hazardous and/or reactive organic gases. Particle size, mass and composition also were measured and are being reported separately. Comparison of the emissions of nine hazardous air pollutants from these two engines with emissions from nine other aircraft engines is discussed.     

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available.In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM₁₀ and PM_2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM₁₀ in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650–1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called “pulling equations”.ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m^?3 (17%) in PM₁₀, 2.2 μg m^?3 (8%) of PM_2.5 and 0.3 μg m^?3 (2%) of PM₁. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM₁₀, PM_2.5 and PM₁. Therefore the overall traffic contribution resulted in 18 μg m^?3 (46%) in PM₁₀, 14 μg m^?3 (51%) in PM_2.5 and 8 μg m^?3 (48%) in PM₁. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.     

Analysis of cloud and precipitation chemistry at Whiteface Mountain,NY

Federal and state programs over the past two decades have resulted in the reduction of emissions of precursors of acid rain. Concomitant with these changes, measured concentrations of acidity in precipitation and in watersheds have shown a downward trend or improvement. However, another pathway for these precursors is through cloud and fog events that often tend to occur at high-elevation regions affecting the fauna and flora as well. In this study we report on long-term measurements of cloud water and precipitation chemistry made from 1994 onwards at a high-elevation location, Whiteface Mountain NY, in the northeastern United States. Trends and inter-relationship between the ions were examined along with ambient SO₂ measurements and Adirondack lakes chemistry data.     

Assessment of source apportionment by Positive Matrix Factorization analysis on fine and coarse urban aerosol size fractions

This study was conducted in order to investigate the differences observed in source profiles in the urban environment, when chemical composition parameters from different aerosol size fractions are subjected to factor analysis. Source apportionment was performed in an urban area where representative types of emission sources are present. PM₁₀ and PM₂ samples were collected within the Athens Metropolitan area and analysed for trace elements, inorganic ions and black carbon. Analysis by two-way and three-way Positive Matrix Factorization was performed, in order to resolve sources from data obtained for the fine and coarse aerosol fractions. A difference was observed: seven factors describe the best solution in PMF3 while six factors in PMF2. Six factors derived from PMF3 analysis correspond to those described by the PMF2 solution for the fine and coarse particles separately. These sources were attributed to road dust, marine aerosol, soil, motor vehicles, biomass burning, and oil combustion. The additional source resolved by PMF3 was attributed to a different type of road dust. Combustion sources (oil combustion and biomass burning) were correctly attributed by PMF3 solely to the fine fraction and the soil source to the coarse fraction. However, a motor vehicle's contribution to the coarse fraction was found only by three-way PMF. When PMF2 was employed in PM₁₀ concentrations the optimum solution included six factors. Four source profiles corresponded to the previously identified as vehicles, road dust, biomass burning and marine aerosol, while two could not be clearly identified. Source apportionment by PMF2 analysis based solely on PM₁₀ aerosol composition data, yielded unclear results, compared to results from PMF2 and PMF3 analyses on fine and coarse aerosol composition data.